Lightmybricks LEGO Old Trafford Manchester United User manual

Please note: This page lists instructions for the LED light kit only.

Package Contents:
12x White Strip Lights
4x Blue Strip Lights
2x Blue 30cm Bit Lights
4x White 15cm Bit Lights
3x 2-Port Expansion Boards
1x 6-Port Expansion Board 1x 8-
Port Expansion Board
10x 5cm Connecting Cables 8x 15cm
Connecting Cables
2x 30cm Connecting Cables
1x USB Power Cable
LEGO Pieces:
4x Round Plate 1×1 with Open Stud (Black)
4x Black 1×1 Modified Plate Rounded with Handle
4x Arm Skeleton, Bent with Clips at 90 degrees (Any Colour)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid
correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables;
instead ensure they are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be
inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on
the left side of the port. The connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do
not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible
overheating of the expansion board when connected.

Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the
connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector,
don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board
Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards.
Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables
to Strip Lights. With the expansion board facing up, ensure the side of the connector with the
wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.

Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow
LED component exposed). You can either place them directly on top of LEGO® studs or in
between.

OK, Let’s Begin!
1.) We will start by installing lights to the left section of the stadium. Firstdisconnect all the
main sections, then take the left section and disconnect the roof via the railing clips towards the
inside.

2.) Disconnect the top section of seats, then take out the USB Power Cable and thread the
connector end of the cable through the left space. Pull the cable in through the inside where the
seats were connect to and connect it to a White Strip Light.

Take a 15cm Connecting Cable and connect it to the strip light’s right port, then using it’s
adhesive backing, stick the Strip Light underneath the top seat section in the following position.
Ensure the 15cm cable is on the left side, with the clips on the bottom as shown below.

Reconnect this section to the stadium ensuring the 15cm connecting cable is laid out the left
side.

3.) Connect the other end of the 15cm cable to a new White Strip Light. Take a 30cm
Connecting Cable and connect it to the strip light’s right port.
Take the roof section and turn it over so we can access underneath. Using the adhesive backing,
stick the Strip Light underneath the roof towards the front as shown below.
Secure the 15cm cable underneath the white tile on the left side, then reconnect the roof to the
stadium.