Lightmybricks LEGO Winter Village Post Office 10222 User manual

The following page is the instructions for the Light My Bricks LEGO Winter
Village Post Office (10222) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Winter Village Post Office (10222)
LED light kit , please click here to view the product page
Light My Bricks: LEGO Winter Village Post
Office 10222 Lighting Kit

Package Contents:
4x White 15cm Micro Bit Lights
5x White 15cm Bit Lights
11x Flashing White 15cm Bit Lights
2x White Strip Lights
1x Micro 4-Port Expansion Board
4x 6-Port Expansion Board
1x Flicker Effects Board
2x 5cm Connecting Cables
3x 15cm Connecting Cables
1x 30cm Connecting Cable
1x AA Battery Pack (requires 3x AA Batteries)
1x Flat Battery Pack (requires 2x CR2032 Batteries)
8x 3M Adhesive Squares
LEGO Pieces:
1x Trans Clear Plate w Rounded Bottom 2×2
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably

in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Connecting Micro Cable connectors to Micro
Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is

similar to connecting lights and cables to Strip Lights. With the expansion
board facing up, ensure the side of the connector with the wires exposed is
facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.

OK, Let’s Begin!
1.) We will first install lights to the post office truck. Disconnect the following
sections surrounding the front and back of the truck as shown below:

Disconnect the two headlight sections and disassemble one of them as shown
below

2.) Take a White 15cm Micro Bit Light and with the cable facing the same way
as the tap, place the LED inside the plate underneath. Ensuring the LED is
facing the correct way up, secure the Bit Light in place by reconnecting the
trans clear round plate.
Reconnect the tap piece to the dark grey plate with clip ensuring you secure
the cable underneath the clip as shown below, then reconnect this headlight to
the front of the truck.

Repeat this process to install another White 15cm Micro Bit Light to the other
headlight, before reconnecting it to the front of the truck.

3.) Lay both cables in between studs leading to the back of the truck, then
secure them in place by reconnecting all the pieces we removed earlier over
the top.