Lightmybricks LEGO Winter Village Fire Station 10263 Lighting... User manual

The following page is the instructions for the Light My Bricks LEGO Winter
Village Fire Station (10263) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format
here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Winter Village Fire Station
Light My Bricks: LEGO Winter Village
Fire Station 10263 Lighting Kit
(10263) LED light kit , please click here to view the product page

Package Contents:
2x White 30cm Bit Lights
9x White 15cm Bit Lights
10x Flashing White 15cm Bit Lights
3x White Strip Lights
1x Blue Strip Light
4x 6-Port Expansion Board
1x 8-Port Expansion Boards
1x 5cm Connecting Cable
3x 15cm Connecting Cables
1x 30cm Connecting Cables
2x 50cm Connecting Cables
1x AA Battery Pack (requires 3x AA Batteries)
1x Flat Battery Pack (requires 2x CR2032 Batteries)
8x Adhesive Squares
LEGO Pieces:
4x Trans Red Round Plate 1×1
4x Trans Yellow Round Plate 1×1
2x Trans Blue Round Plate 1×1
2x Trans Green Round Plate 1×1
2x Plate 1×6(any colour)
1x Plate 1×2 (any colour)

Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side

with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Installing lights to the Fire Truck
1.) We will first install head and tail lights to the fire truck. Take the truck and
disconnect the front section from the vehicle, then disconnect the two trans
yellow round tiles from it.

Take a White 15cm Bit Light and thread the connector end of the cable
through the front of one of the side pieces. Thread the cable all the way
through, then flatten the Bit Light against the edge of the round stud. Secure
the Bit Light in place by connecting a provided Trans Yellow Round Plate 1×1
over the top.

Repeat this step to install another White 15cm Bit Light to the other side,
securing it in place using another provided Trans Yellow Round Plate 1×1.

2.) Flip this front section over then take the cable from the right side and fold it
over to the left side before reconnecting this section back to the front of the
vehicle. Ensure that both cables are laid toward the left.
Flip the truck over and lay it on its left side. Take both cables and bring them

behind the front right wheel
3.) Turn the truck around and disconnect the black 2×12 plate from underneath,
then disconnect the back wheel section
Disconnect the tail light section from the back wheel then disconnect the two

trans red round tiles.
4.) Take a White 15cm Bit Light and with the cable facing down, place it over
the left stud as shown below. Secure the Bit Light in place by connecting a
provided Trans Red Round Plate 1×1over the top.