Lightmybricks LEGO Joker Manor 70922 Lighting Kit User manual

Light My Bricks: LEGO Joker Manor 70922 Lighting Kit
The following page is the instructions for the Light My Bricks LEGO Joker Manor (70922) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow each step carefully.
Please note: This page lists instructions for the LED light kit only.
Package Contents:
4x White 30cm Bit Lights
17x White 15cm Bit Lights
12x Flashing White 30cm Bit Lights

12x Flashing White 15cm Bit Lights
2x Blue 30cm Bit Lights
4x White 15cm Micro Bit Lights
8x White Strip Lights
1x Green Strip Lights
2x Multi Colour Strip Lights
1x Micro 2-4 Port Expansion Board
3x 6-Port Expansion Boards
3x 8-Port Expansion Boards
3x 12-Port Expansion Boards
1x Flicker Effects Board
4x 5cm Connecting Cables
8x 15cm Connecting Cables
9x 30cm Connecting Cable
1x USB Power Cable
6x Adhesive Squares
LEGO Pieces:
3x Trans Clear Round Plate 1×1
2x Trans Clear Plate w Rounded Bottom 2×2
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT
forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.
Spot Light LEGO Pieces
2 x Black Dish Inverted 3
×
3
x Black Plate 2 2
×
6
2 x Black Plate 1
×
2 modified w Handle on End
2 x Black Tile 1
×
1 w Clip
4 x Black Plate 1
×
2 modified with stud jumper

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing
up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=”
symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when
connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will
damage the plug and the connector.

Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place
them directly on top of LEGO® studs or in between.
OK, Let’s Begin!

1.) We will start by lighting up the front entrance. First disconnect the cherry bombs on either side as well as the two light sections surrounding the
entrance.
2.) Take the left light section and disconnect the following pieces as well as trans clear round plates:

Take a White 15cm Bit Light and with the cable facing down, place it over the far left stud on this section. Secure the Bit Light in place by
reconnecting one of the trans clear round plates over the top.
3.)
Repeat previous step to install another
5 x White 15cm Bit Lights
to this section as shown below:

Fold the cables down at the edge of the yellow plates, then reconnect the pieces we removed earlier. Folding the cables down will prevent them from
snapping when you reconnect pieces over the top. Ensure the cables underneath plates are laid in between studs.
4.) Take a 12-Port Expansion Board and connect all six cables to it. Take a USB Power Cable and connect it to the expansion board, then
connect the other end of it to your USB Power Bank (sold separately) . Turn the power bank ON to test all lights are working OK.

Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the
expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports,
please view the section addressing expansion board issues on our online troubleshooting guide.
Disconnect the USB Power Cable from the expansion board, then turn the light section over and bring all six cables together and twist/wind them
around each other closest to the top. Continue to twist/wind the cables all the way to the end so they come together to form a larger neat cable.
5.) Take 3x 30cm Connecting Cables and connect one end of each of them to the 12-port Expansion Board.

Take a Flicker Effects Board and connect a 5cm Connecting Cable to the IN port. Connect the other end of the cable to the 12-port expansion board.
6.) Take the other of the last 30cm Connecting Cable connected to the 12-port expansion board and thread it through the left side of the entrance
space. Pull it out from the other side and pull it all the way up behind the left “boxing glove”. Secure the cable underneath the bottom of the
“Joker” sign by looping it around the frame a few times. Reconnect the left light section of the entrance using the clip on top as shown below:

Thread the other two 30cm Connecting Cables all the way through the entrance, then hide the expansion board and effects board toward the inside
left.