Lightolier 1102T series Instructions for use

(
(
STEP3R
,.,.,.,
.,,
”
..... ,.,.,.,..,,:,,.,’ .,, ,, . .
REFLECTOI
HOUSING
F
SOCKET CUP SIDE
OPENING
F
READAND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO.
This fixture is intendedfor installationin accordancewith the NationalElectricalCodeand local
regulations.To
assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. Toprevent eleckical shock, turnoff electricity at fuse box before proceeding. IS:1105T
Retainthese instructionsfor maintenancereference. R0791Page 1of 2
INSTRUCTIONS FOR LWECASTER REFLECTOR TRIM INSTALLATION IN THE
II02T SERIES FRAME-IN KIT
INSTALLINGREFLECTORTRIM
1,Installframe-in kit. (Seeframe-in kit instructionsheetfor installation STEP1
procedure,)
2.Rotate(4)roto-clipsclockwisesothattheshortlegsextendinwardtoward
the centeropening, (NOTE:The short legof the roto-cliphasno return
ontop.)
3. Insertsocket cupthroughsideopening inthe reflectorhousingandpull
through (DO NOT SNAP CUP IN PLACE).
4. Align side opening onreflectorhousing directly opposite of J-box assembly
(See diagram for STEP 5) and push reflector housing straight up until it is
secureagainstthe ceiling, Makesurethatside openingonthe reflector
housingclearsthe roto-clipswhileit is beingpushedin place.
NOTE:Toremovereflectorhousing,turncounterclockwisewhilepulling
downward, STEP2
5,Pushsocketcup intosideopeningin reflectorhousingandsnapinplace. SHORT LEG
Y
ONG LEG
(with return)
LAMPING
1. Use (2) 13W twin tube compact fluorescent lamps, 7G
2. To lamp fixture, insert the head of the lamp through the lamp openings in ‘“ME> “
the reflector housing and then insert the base of the lamp into the socket, CE’’L’NGV:’:;+ :.:0 ROTO-CLIP (4)
Yi:-
?
LBC31=[ 7-C>1-1E R“
ER#R?:;s%it

IS1105T
INDIVIDUAL TRIM INSTALLATION INSTRUCTIONS 0591
Page 2of 2
A. CROSS BLADE BAFFLE (1132T) IB. DROPPED OPALEX DIFFUSER (1178T)
REFLECTOR
~r ‘O”s’NG
7CROSS BLADE BAFFLES
S@%-
1—
ALIGN
MULTll~E~&FFLES
-CRO” B~DE BAFFLE
I
““’’’R-’9
go
(3) DIMPLE —
t(3) SLOT
w
LINE UP WITH
DIMPLE
DIFFUSER >
J& O~:N
C. STEP BAFFLE WALL WASHER (1135T)
CATCHp.+’’y+,,,,,x
%A--Ma\
F= STEP BAFFLE f
—WALL WASHER
D. STEP BAFFLE AND ALZAK CONES
WITH DIFFUSER (1114T)
a-
.——
BAFFLE
(OR CONE)
E. LENSLITE (1126T), DIFFUSER (1128T)
TORSIONTITE
SLOT
TORSIONTITE
SPRING
TO RELAMP:
Simplygripflange of TRIM RING,then
pull down (Fig.m).
—
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER INC. USE OF OTHER
MANUFACTURERS’ REFLECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND
COULD CONSTITUTE AFIRE HAZARD.