Lightolier STEM KIT User manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:FACSA36
0697 Page 1 of 2
INSTALLATION OF STEM KIT TO CALCULITE®COMPACT FLUORESCENT CYLINDER.
STEM KITS ARE SUITABLE FOR DAMP OR DRY LOCATIONS.
A. TO INSTALL STEM KIT ON CEILING
NOTE: STEM may be shortened by cutting STEM to desired
length. This must be done before hanging. Detach STEM from
STEM KIT by loosening SET SCREW from BALL SWIVEL. Be
sure that LEAD WIRES are completely out of STEM. Cut STEM,
then drill 1/8” diameter hole through the STEM 3/16” from
end. Be certain to deburr after cutting or slotting. (Fig. 1) (A
slot made with a file or hacksaw will also work.) Reassemble
STEM and BALL SWIVEL.
1. Bring SUPPLY LEAD WIRES from the OUTLET BOX through
the center hole of the MOUNTING STRAP. For sloped ceil-
ings, position opening in MOUNTING STRAP facing upward,
then thread SCREWS through MOUNTING STRAP to OUTLET
BOX. (Fig. 2 &3)
2. Slide CANOPY down STEM to rest on STEM JOINT. (Fig. 3)
3. Hook BALL SWIVEL on MOUNTING STRAP. Make sure
GROOVE in BALL SWIVEL aligns with TAB in MOUNTING
STRAP. (Fig. 4)
4. Slide SAFETY CLIP to MOUNTING STRAP and tighten
SCREW. (Fig. 4)
5. Make electrical connections: connect FIXTURE GROUND to
the ELECTRICAL SYSTEM GROUND. WHITE FIXTURE LEAD
or LEAD WITH TRACER MARK to WHITE SUPPLY WIRE.
BLACK FIXTURE LEAD or FIXTURE LEAD WITHOUT TRACER
MARK to BLACK SUPPLY LEAD, with WIRE NUTS (provided).
Push all splice connections into OUTLET BOX.
6. Align TABS in CANOPY with notches in MOUNTING STRAP.
Slide CANOPY up over MOUNTING STRAP and push up
against ceiling. (Fig. 3)
BALL SWIVEL
1/8” DIA.
SET SCREW
3/16”
Fig. 1 STEM
38°
CEILING LINE
BALL ALIGN-
MOUNTING STRAP
STEM
OPENING
Fig. 2
Fig. 3
OUTLET BOX
(BY OTHERS)
SUPPLY LEAD
MOUNTING
STRAP
MOUNTING
CANOP
STEM
STEM JOINT
ADAPTER PLATE
TABS
WIRE NUTS
Fig. 4
BALL SWIV- GROOVE
SAFETY CLIP
MOUNTING
STRAP
STEM
TAB
SCREW

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:FACSA36
0697 Page 2 of 2
B. TO ATTACH FIXTURE TO STEM
1. Attach (2) SPRING CLIPS to FIXTURE HOUSING by sliding
SPRING CLIPS onto (2) raised pockets on top of FIXTURE
HOUSING. (Fig. 5)
2. Make electrical connections: connect STEM KIT FIXTURE
GROUND to HOUSING FIXTURE GROUND. STEM KIT
FIXTURE WHITE LEAD to HOUSING FIXTURE WHITE LEAD.
STEM KIT FIXTURE BLACK LEAD to HOUSING FIXTURE
BLACK LEAD. Use WIRE NUTS (provided).
3. Align (2) holes in COVER with (2) SPRING CLIPS secured
on top of FIXTURE HOUSING. (Fig. 6) Assemble FIXTURE
HOUSING to STEM KIT using (2) SCREWS (provided).
SPRING CLIP
RAISED POCK-
SCREWS
(2) PROVIDED
COVER
WIRE NUT
(3) PROVIDED
SPRING
CLIPS
(PROVIDED)
FIXTURE
HOUSING
Fig. 5
Fig. 6