Lightolier 1000LV User manual

/INSTRUCTIONSHEETNO.
INSTALLATION PROCEDURE FOR LOW VOLTAGE
REFLECTOR TRIM IN THE 1000LV FRAME-IN KIT lS:1055LV
0s90 Page 1of 2
READ AND UNDERSTAND THESE lNSTRU~lONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulation.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
~~%~
FIG. AFIG. BFIG. CFIG. D
1. FRAME-IN 2. CLOSE-IN 3. SNAP~N 4. PUSH-UP
WARNING: BEFORE INSTALLING REFLECTOR TRIM TO FRAME-IN KIT, REAO MARKINGS IN REFLECTOR TRIM
AND ‘IN BOCK~ CUP OF FRAME-IN-KIT TO DErERMINE LAMP WAlTAGE AND TYPE APPLICABLE FOR YOUR
lNBTA1.L&TiON. IF I.C. TYPE FRAMING KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITN INSULATED
CSIUNGS. IF ANON I.C. TYPE FRAME4N.KfT IS USED, DO NOT INSTALL INSULATION WITHIN 31NCHSB OF FI)MJRE
SIDE OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH AMANNER TO ENTRAP HSAT.
1. FRAME-IN (Fig. A)
See Frame-In Kit Instruction Sheet for installation
4
r-
procedure. FRAMINGKIT
,!;;
2. ROTATE ROTO-CLIPS (Fig. B) MOUNTSFLUSH
ONCEILINGMATERIAL
,..’
As shown in Fig. E. 0“ \
.-.,,:.,--
;’,.’.’.; :.:.-..,
3. SNAP.ON (Fig. C). , ....:.:
-... .’$.’.
Insert SOCKET through RECTANGLE HOLE on top \..,-.... .- CEILING
-,:.-...-:.
of REFLECTOR TRIM. Engage TAB from SOCKET MATERIAL
CUP into one of the SLOTS on top of REFLECTOR ROTO.CLIP ‘““::;~y ; POSITION
TRIM and push other end of SOCKET CUP with :., ,,
LANCING into the other SLOT (Fig. F), FIG. E
4. PUSH-UP (Fig. D). –SOCKETCUP
Push REFLECTOR TRIM into ceiling until flange
is flueh to ceiling (Fig. D). RECTANGLEHOLE ~
N~E Socket manufacturers have suggested that SLOTa
socket may fail after 3to 6ralampings. If this
occurs, socket can be replaced by disconnecting REFLECTORTRIM
male connectors (attached to socket leads) from
female connectors (attached to fixture leads) and
replacing it with anew socket procured through
Lightolier (Fig. G).
INSULATINGSLEEVING MALECONNECTORa
SEE BACK PAGE FOR LAMP INSTALLATION (ATTACHEDTO SOCKETWIRE)
AND ADJU~MENT.
FEMALECONNECTORS
(ATTACHEDTO FIXTUREWIRES) MR16SOCKET
FIG. G
1- I<51“17<> l-l 1= ,a@ :v:::::i,N:r::::,E:i:T:j

LAMPING INSTRUCTIONS AND ADJUSTMENTILOCKING
INSTALL LAMP
5.
6.
7.
s.
Remove LAMP RING from LAMPIYOKE HOLDER by
pulling straight down (Fig. H).
insert LAMP (MR-16) between LAMP SPRINGS until
face of LAMP sits firmly on GLASS LAMP GUARD
(Fig, l).
Attach SOCKET to hi-in prongs on LAMP (Fig. l).
Insert LAMP RING with LAMP and GLASS LAMP
GUARD attached back into LAMP/YOKE HOLDER
(Fig. J).
~
WARNING: LAMP MANUFACTURERS REQUIRE THE
GLASS IAMP GUARD BE IN PLACE BEFORE ENERGIZING
LAMP AND THAT GREAT CARE MUST BE TAKEN THAT
LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID
FINGER MARKS WHEN HANDLING FOR THEY MAY CAUSE
SHORT LAMP LIFE AND POSSIBLE BREAKAGE.
VERTICAUANGLE ADJUSTMENT AND LOCK (Figd)
9. krserl ascrewdriver into the LOCKING GUIDE on the
LAMP/YOKE HOLDER, and locate the clot in the
VERTICAL ADJUST/LOCK SCREW, turn the SCREW
counterclockwise, and using the screwdriver as a
lever, tilt the entwe UMPIYOKE HOLDER to the
desired angle. Once the desired angle ie reached,
tighten screw by turning screwdriver clockwise.
HORIZONTAL ADJUST AND LOCK (Fig. J)
10. The entire IAMPIYOKE HOLDER can be horizontally
rotated to aim the an Ie of light as it leaves the hole
%
in the APERTURE TRI (Fig. J). This can be done by
backing off the HORIZONTAL ADJUST/LOCK SCREW
one full turn, freeing the SUPPORT PLATE (Fig J).
Grasping the YOKES on either side of the
LAMP/YOKE HOLDER, rotate the SUPPORT PUTE
to the desired angle and lock the position by
tightening the HORIZONTAL ADJUST/LOCK SCREW.
RELAMPING: The locking mechanisms designed within this
fixture allow ralamping without having to readjust and
relock. Follow Steps 5-8.
NOTE 1. LOW VOLTAGE FIXTURES should be
dimmed only with special dimmers Intended
apeclfloslly for that purpose Use Lightoiier
Lytemodej Soenlst, Cresoendo VA, Neptune VA,’
Preolelon VA, Essveet VA, Sunrise VA, Rediant VA or
IS1055LV
0890
Page 2of 2
fs~
/.
-
==77=.
LAMP
SPRING
c
I-44:
GL4S&5L~MP FIG. H
FIG. I
ET
equlvelant pfidu6te by others or vsrisbie auto.
transformer’e or eieotmnlo dimmers intended for use
with low voltage flxturee. 2. Low voltsge fixtures msy
produoe audible eound when used with externel
dimmem which may be ob]ectional in acoustically
critical eree% DE
LAMP
GtiG~ARLMP
rLAMP
/
.
FIG. J
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED By LIGHTOLIER INC. USE OF ~ER MANUFA~RERS’
RSFLECTDR TRIMS VOIDS THE UNDER~rERS LABORATORIES LISTING AND COULD CONSfTfUTE AFiRE HAZARD.