Lightolier HE Series User manual

HE Series
CLASS I DIVISION 2 EMERGENCY LIGHTING
Page 1 of 2
Job Information Type:
Job Name:
Cat. No.:
Notes:
Features
Illumination: Illumination
is accomplished with lamp
heads mounted on the top of
the unit. The Class I, Div. 2
rated “H” Series lamp head
is available in a variety of
wattages, and is constructed of
gray polycarbonate to match
the housing.
Housing: Constructed of
impact-resistant, fiberglass-
reinforced polyester. Housing
color is gray and includes
stainless steel hardware. The
HE Series is UL listed for
Class I, Division 2, Groups
A, B, C & D; Class I, Zone
2, Groups IIA, IIB (+ H2) &
IIC; and Class II, Division 2,
Groups F & G. View-through
window allows easy monitoring
of the optional voltmeter and
ammeter. Available with Class
I, Div. 2 rated polycarbonate
sealed beam Par 36 tungsten or
halogen lamp heads.
Operating Temperature
Range: Standard location
65°F (19°C) to 85°F (30°C)
Electrical Specifications:
Lead Calcium
6 VDC 25 & 50 W:
0.18 A (120), 0.08 A (277)
12 VDC 25, 50, 100 & 125 W:
0.40 A (120), 0.18 A (277)
NiCad
6 & 12 VDC 25 W:
0.088 A (120), 0.042 A (277)
6 VDC 50 & 75 W, 12 VDC
50 W:
0.19 A (120), 0.084 A (277)
12 VDC 75 & 100 W:
0.29 A (120), 0.14 A (277)
12 VDC 125 & 150 W:
0.39 A (120), 0.18 A (277)
Diagnostic Electronics
(standard): 120/277 VAC
dual voltage input with surge
protection is standard on all
models. Charging system is
microprocessor driven with
software embedded diagnostic
routine and precision
temperature compensation.
Surge protection, brownout,
AC lockout, and low voltage
disconnect features are
standard.
Self-Testing Diagnostics
(optional): The diagnostic/
charging platform with self-
testing mode automatically
runs a one-minute self-test
every 30 days and a 30-minute
test on the sixth and twelfth
month. A one-minute or
90-minute test may be initiated
via the push to test switch on
the unit or by activating the
appropriate test command on
the optional IR test device.
Code Compliance
UL 924 and 844 listed. NFPA
101, NEC, BOCA, OSHA and
IBC illumination standards.
Temperature Rating (T-Rating)
160° (T3C). Class I, Zone 2
T-Rating 200° (T3).
Warranty
Three year full electronics
warranty. One year full plus
four year prorated lead calcium
battery warranty. Five year full
plus five year prorated nickel
cadmium battery warranty.
13.2"
(33.5 cm)
15.2"
(38.6 cm)
HE125L2HH8SD2
7.1"
(18.0 cm)
21.4"
(54.4 cm)

HE Series
CLASS I DIVISION 2 EMERGENCY LIGHTING
Page 2 of 2
Philips Lightolier
e: [email protected]
t: [phone]
w: www.lightolier.com
HE Series August 4, 2011
Specifications are subject to change without notice.
© Koninklijke Philips Electronics N.V., 2011.All rights reserved.
Job Information Type:
Ordering Information
Series
HE1 = 6 VDC
Class I Div. 2
Emergency Lighting
Unit
HE2 = 12 VDC
Class I Div. 2
Emergency Lighting
Unit
6 V Lead Calcium
25L = 25 Watt Unit
50L = 50 Watt Unit
6 V Nickel Calcium
25N = 25 Watt Unit
50N = 50 Watt Unit
75N = 75 Watt Unit
12 V Lead Calcium
25L = 25 Watt Unit
50L = 50 Watt Unit
100L = 100 Watt Unit
125L = 125 Watt Unit
12 V Nickel Calcium
25N = 25 Watt Unit
50N = 50 Watt Unit
75N = 75 Watt Unit
100N = 100 Watt Unit
125N = 125 Watt Unit
150N = 150 Watt Unit
Battery/DC Voltage # of Heads
Blank = No Lamp Heads
1= One Lamp Head
2= Two Lamp Heads
3= Three Lamp Heads
Lamp Heads
6 V Tungsten
HT8 = 8 Watts
HT12 = 12 Watts
HT18 = 18 Watts
HT25 = 25 Watts
6 V Halogen
HH8 = 8 Watts
HH12 = 12 Watts
12 V Tungsten
HT12 = 12 Watts
HT18 = 18 Watts
HT25 = 25 Watts
12 V Halogen
HH8 = 8 Watts
HH12 = 12 Watts
SD2 = Diagnostic
Electronics
Model Designator1
Optics
Wall Mounted 7.5' AFF, 12 V 12 W Halogen Lamp Heads Represented
1 FC Average
Note
1) Some option combinations may impact
UL listing. Consult factory for specifications.
7.5 ft.
30 ft.
9 ft.
Average initial footcandles at floor = 1.12
Maximum initial footcandles at floor = 4.9
Minimum initial footcandles at floor = 0.2
Maximum to minimum ratio = 24.50
* The optics layout shown is intended to be used as reference only. Standard reflectances used were 80/50/20. Lightolier is not responsible for site specific conditions that
may alter the results.
.2
.3
.2
.8
1.3
.4
2.7
3.1
.6
2.2
2.1
.5
.9
.8
.5
1.0
.8
.5
2.3
1.9
.5
2.7
3.3
.6
.8
1.3
.5
.2
.3
.2
.2
.3
.2
.8
1.3
.4
2.8
3.1
.6
2.2
2.0
.5
.9
.8
.5
.9
.7
.5
2.4
1.9
.5
2.6
3.2
.6
.7
1.3
.4
.2
.2
.2
SD2
A= Ammeter
EX = Special Input Transformer (specify
voltage & frequency)
T= Self-Testing Diagnostics
TA = Audible Self-Testing Diagnostics
TD = Time Delay (15 minutes)
V= Voltmeter
Factory Installed Options1
Accessories (order as a separate item)
SDREMOTE = Infrared Remote Test
Device
WG = Wire Guard