Lightware RAP-B511-EU-K User manual
RAP-B511-EU -K, -W, -S
RAP-B511-UK -K, -W, -S
RAP-B511-US -K, -W, -S
User’s Manual
Room Automation Panel
RAP-B511 series – User's Manual 2
Important Safety Instructions
Class II apparatus construction.
The equipment should be operated only from the power source
indicated on the product
To disconnect the equipment safely from power, remove the power
cord from the rear of the equipment, or from the power source. The
MAINS plug is used as the disconnect device, the disconnect device
shall remain readily operable.
There are no user-serviceable parts inside of the unit. Removal of the
cover will expose dangerous voltages. To avoid personal injury, do not
remove the cover. Do not operate the unit without the cover installed.
The appliance must be safely connected to multimedia systems.
Follow instructions described in this manual.
Ventilation
For the correct ventilation and to avoid overheating ensure enough
free space around the appliance. Do not cover the appliance, let the
ventilation holes free and never block or bypass the ventilators (if any).
WARNING
To prevent injury, the apparatus is recommended to securely attach to
The apparatus shall not be exposed to dripping or splashing and that
be placed on the apparatus.
CAUTION AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
Waste Electrical & Electronic Equipment
WEEE
This marking shown on the product or its literature,
indicates that it should not be disposed with other
household wastes at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material
resources. Household users should contact either the
retailer where they purchased this product, or their local government
environmentally safe recycling. Business users should contact their
supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for
disposal.
The Handling of the Batteries
Use only standard batteries. Do not use new and used batteries
together. This may cause a battery to break or leak and may cause
insert them with right polarity. Otherwise, the battery may become
leakage of the internal liquid. The batteries (and rechargeable
batteries) are not ordinary refuse and must be returned for recycling
purposes. The customer is responsible for returning the used or
rechargeable batteries for recycling. Be careful that children do not
place the batteries in their mouths when removed from the remote
control. Place the battery in a location that children or infants cannot
reach.
Correct Disposal of Batteries in this Product
This marking on the battery indicates that the batteries in this product
should not be disposed of with other household waste at the end of
indicate that the battery contains mercury, cadmium or lead above the
disposed of, these substances can cause harm to human health or the
environment. To protect natural resources and to promote material
reuse, please separate batteries from other types of waste and recycle
them through your local, free battery return system.
Common Safety Symbols
Symbol Description
Direct current
Alternating current
Double insulation
RAP-B511 series – User's Manual 3
Symbol Legend
The following symbols and markings are used in the document:
WARNING! Safety-related information which is highly
recommended to read and keep in every case!
ATTENTION! Useful information to perform a successful procedure;
it is recommended to read.
INFO: A notice which may contain additional information. Procedure
can be successful without reading it.
DEFINITION: The short description of a feature or a function.
be useful.
Navigation Buttons
Go back to the previous page. If you clicked on a link previously,
you can go back to the source page by clicking the button.
Step back one page.
Step forward to the next page.
Document Information
Allpresentedfunctionsrefertotheindicated products.The descriptions
have been made during testing these functions in accordance with the
Item Version
Lightware Device Controller (LDC) software v1.30.0b2
Lightware Device Updater2 (LDU2) software v.1.2.2
Controller rmware package version v1.0.1b1
Hardware 1.0
Document revision: 1.1
Editor: Judit Barsony
About Printing
Lightware Visual Engineering supports green technologies and
Eco-friend mentality. Thus, this document is made for digital usage
primarily. If you need to print out few pages for any reason, follow the
recommended printing settings:
▪Page size: A4
▪Output size: Fit to page or Match page size
▪Orientation: Landscape
around the content (gray on the second picture below) makes
possible to organize the pages better. After punching the printed
pages, they can be placed easily into a ring folder.
123
RAP-B511 series – User's Manual 4
1. INTRODUCTION...................................................................................6
...................................................................................6
........................................................................6
................................................................................6
.......................................................................6
..................................................................7
......................................................................7
2. INSTALLATION.....................................................................................9
.........................................................................9
...........................................................
......................................................................
.................................................................................................
..................................
.................................. 11
.................................. 12
.......................................................................13
........................................................................13
3. PRODUCT OVERVIEW ......................................................................14
...................................................................................14
............................................................................ 15
............................................................................ 15
.....................................................................................15
..............................................................16
.........................................................................
...........................................................................
..................................
................................................................................
......................................................................
4. DEVICE CONCEPT.............................................................................17
.........................................................................17
.....................................................18
.............................................................................................
...............................................................................................
..................................................19
...............................................................................
..........................................................................
................................................................................... 21
................................................................................................. 21
.......................................................................21
............................................................... 21
..................................................................................... 22
................................................................. 22
............................................................. 22
............................................................. 22
...................................................23
................................................................................ 23
............................................................................ 23
...................................................................... 23
.................................................................................. 24
5. SOFTWARE CONTROL - LIGHTWARE DEVICE CONTROLLER ....25
...................................................................25
..........................................................................25
.....................................................26
............................................................................27
............................................................................
.............................................................................
..........................................................................
..........................................................
.............................................................................30
..............................................................................................
................................................................................................. 31
............................................................................................ 32
.................................................................................................. 32
............................................................................34
..................................................... 34
............................................................................... 35
............................................................... 35
.......................................................
.............................................................
...............................................................
.............................................................................37
............................................................................................... 37
............................................................................................ 37
.............................................................................................
..............................................................................38
...............................................................39
6. LW2 PROGRAMMER'S REFERENCE...............................................40
.........................................................40
..............................................................40
...........................................................................
...........................................................................
.................................................................... 41
......................................... 41
................................................... 41
............................................................................... 41
......................................................................... 41
................................................................................... 41
....................................................................... 41
......................................................................... 41
..................................................................... 41
................................................. 41
..............................................................42
............................................................ 42
........................................................................... 42
....................................................................... 42
................................................................ 42
................................................................... 42
....................................................................42
............................................ 42
...............................................43
Table of Contents
RAP-B511 series – User's Manual 5
7. LW3 PROGRAMMERS’ REFERENCE...............................................44
......................................................................................44
...........................................................................44
............ 44
................................................................................... 44
............................................................................. 45
............................................................................... 45
............................................................................... 45
.......................................................................................... 45
..........................................................................................
.....................................................................................
......................
..............................................
.......................................................................47
................................................................. 47
........................................................................ 47
................................................................. 47
........................................................... 47
........................................................................ 47
............................................. 47
....................................................................................... 47
.............................................................................48
.......................................................................
............................................
..........................................
...........................................................
.................................................................................
...................................................
......................................................
......................
............................................................
.........................................
................................................................50
.................................................
...........................................................
......................................................
..................................................... 51
....................................................................... 51
................................................................. 51
.........................................................52
..................................................................... 52
............................................... 52
............................. 53
.....................................................53
............................................................ 53
.............................................................. 53
....................................................................... 53
..................................................54
........................................................... 54
................................................................................ 54
............................................................................. 54
................................. 54
..............................................................56
.....................................................................
..................................................................
.......................................................................
......................................................
...................................................................
...................................................
...........................................................
...........................................
......................................................57
............................................................................. 57
......................................................................... 57
............................................................................... 57
............................................................................. 57
................................................................................. 57
................................................................ 57
............................................................ 57
....................................................................58
..................................................................
....................................................................
.............................................................................
.
.....................
................................
..................................................................
...................................................59
................................................
.........................................................59
.....................................................
...............................................
.....................................................
......................60
....................................................
.............................................
....................................
............................................................
..................................................................62
8. FIRMWARE UPGRADE ......................................................................65
...................................65
................................................................................65
.........................................................66
9. TROUBLESHOOTING........................................................................67
........................68
10. APPENDIX ........................................................................................69
.............................................................................69
............................70
.........................................................70
...............................................................71
....................................................................72
.................................................................73
1. Introduction RAP-B511 series
1
Introduction
chapter we would like to introduce the device highlighting the most important
features in the below listed sections:
Model Comparison
INFO: All the models have the same look and functionality, the only
difference is the size and color of the enclosure.
Model name Color Outlet box type
black
white
RAP-B511-EU-S brushed steel
black
white
brushed steel
black
Double US wall box white
RAP-B511-US-S brushed steel
Box Contents
1The transparent caps are not placed onto the buttons, thus, you
section.
Compatible Devices
Room automation panel has standard RS-232, Ethernet, GPIO ports
and they are compatible with other Lightware products or third-party
devices which have the same signal type.
Button panel Safety & warranty info,
Safety and
Warranty
Info
Quick
Start
Guide
Phoenix
®
combicon
3-pole connector
Phoenix
®
combicon
4-pole connector
Labels for button caps Transparent button caps
in a plastic bag
Description
Room Automation Panel is an integrated control solution for AV
systems installed in collaborative spaces. It features a programmable
keypad, a volume knob, and a processor running Lightware Event
Manager.
3xGPIO and 2xRJ-45 ports provide connection to controlled devices.
make the installation smooth. The additional RJ-45 connector makes
Model Denomination
About the Serial Number
Lightware devices contain a label indicating the unique serial number
of the product. The structure is the following:
RAP-B511-EU-K
Button Outlet box type
Room Automation
Panel
Faceplate color
(Key or Black)
11 buttons altogether
5 buttons in the first line
7A000941
Year of the manufacturing (3-9, A-Y):
7=2017, 8=2018, 9=2019, A=2020, etc...
6-digit running sequence number
Month of the manufacturing (1-9, A-C):
1=January, 2=February, ..., C=December
Ý
Ý
Ý
Ý
Ý
Ý
1. Introduction RAP-B511 series – User's Manual 7
Integrated keypad with 11 programmable backlight buttons. Volume rotary knob to control
Ethernet Control
Remote Power
The RAP-B511 is PoE-compatible and can be powered locally by the supplied power adaptor,
RS-232 Bi-directional RS-232 Pass-through
AV systems can also contain serial port controllers and controlled devices. Serial port pass-
through supports any unit that works with standard RS-232.
RS-232
11
0100 1
x
RS-232 Recognizer
Support recognizing incoming RS-232 messages to integrate with 3rd party devices or
Lightware units.
GPIO Control Port
Infra
Infrared (IR) is a wireless technology used for device communication over short ranges. Third
party control systems may send IR control commands to endpoints turning them on and off
or switching their inputs.
LDC
systems.
Built-in Event Manager
complex environment, there is no need to invest in additional control solutions, which makes
the receiver the best choice for numerous applications.
Real-time clock
Real time clock with network time protocol and automatic daylight saving adjustment for
Event Manager scheduling.
Typical Application
VINX Application Example
VINX-110AP
-HDMI-DEC Workstation 2
1-outputdecoder with HDMI connector
HDMI1.4
Infraport
BidirectionalRS-232
USBHID ext ension
CONNECTbutton(fo r furth er deta ils ple ase see t he User 's manu al)
Shortpress:Acq uire US B conne ction i n multi cast mod e
Lo ng pres s: Rese t to fact ory def aults
Video Strea m ID
0: R eceiv e strea m with Vi deo Str eam ID se t via soft ware
1-15:Recei ve stre am with f ixed Vi deo Str eam ID set b y the swi tch
Front LEDs
POWER
OFF:No power
Bl inkin g: Boot ing
Co ntinu ous: Power connected
VIDEO
OFF:No c onnec tion wi th ENCO DER
Bl inkin g: Connectedto ENCODER, no videooutput
Continuous : Conne cted to E NCODE R, vide o outpu t
USB
OFF:NoUSB co nnect ion
Continuous : USBconnection aquired
VINX-110AP-HDMI-DEC
HDMIOUTPUT
SFP
POWER
VIDEO 1GbELAN
(AVINPUT)
LINK ACT.
DECODER
DCIN
AUDIO
OUT
AUDIO
IN
UNICAST
MODE
ONLY
12V1A
DECODER
HD
display
CATx
HDMI
USB
Audio
HDMI
(localout)
MODE
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
1234
8-4-2-1
ENCODER
2-outputencoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
MODEb utton ( for fur ther de tails p lease s ee the Us er's man ual)
Shortpress:Togg le betw een bes t video q ualit y and ada ptive d ata rate
Long press:Re set to fa ctory d efaul ts
Video Strea m ID
0: T ransm it stre am with V ideo Str eam ID se t via sof tware
1-15: Trans mit str eam with f ixed Vi deo Str eam ID se t by the sw itch
FrontLEDs
POWER
OFF:Nop ower
Bl inkin g: Boot ing
Co ntinu ous: Power connected
VIDEO
OFF:No c onnec tion wi th DECO DER
Bl inkin g: Conn ected t o DECOD ER, no vi deo out put
Continuous:Connec ted to DE CODER , video s ignal d etect ed on HDM I input
POWER and VID EO
Blinking:Video Str eam ID co nflic t in the ne twork
VINX-120-HDMI-ENC
1-outputdecoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
CONNECT but ton (fo r furth er deta ils ple ase see t he User' s manua l)
Shortpress:Acquire USBconnection in multicast mode
Lo ng pres s: Rese t to fact ory def aults
Video Strea m ID
0: R eceiv e strea m with Vi deo Str eam ID se t via soft ware
1-15: Recei ve stre am with f ixed Vi deo Stre am ID set b y the swi tch
FrontLEDs
POWER
OFF:Nop ower
Bl inkin g: Booting
Co ntinu ous: Power connected
VIDEO
OFF:No c onnec tion wi th ENCO DER
Bl inkin g: Conn ected t o ENCOD ER, no vi deo out put
Continuous : Connectedto ENCODER, videooutput
USB
OFF:NoUSB connection
Continuous : USBconnection aquired
VINX-110-HDMI-DEC
HDMIOUTPUT
CONNECT
POWER
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
12 3 4
8-4-2-1
DECODER
1-outputdecoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
CONNECTbutton(fo r furth er deta ils ple ase see t he User 's manu al)
Shortpress:Acq uire US B conne ction i n multi cast mod e
Lo ng pres s: Reset tofactory defaults
Video Strea m ID
0: R eceiv e strea m with Vi deo Str eam ID se t via soft ware
1-15:Recei ve stre am with f ixed Vi deo Str eam ID set b y the swi tch
FrontLEDs
POWER
OFF:No power
Bl inkin g: Booting
Continuous: Powe r con nect ed
VIDEO
OFF:No c onnec tion wi th ENCO DER
Blinking: Conn ected t o ENCOD ER, no vi deo out put
Continuous:Connec ted to EN CODER , video o utput
USB
OFF:NoUSB connection
Continuous : USBconnection aquired
VINX-110-HDMI-DEC
HDMIOUTPUT
CONNECT
POWER
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
12 3 4
8-4-2-1
DECODER
1-outputdecoder with HDMI connector
HDMI1.4
Infrapor t
BidirectionalRS-232
USBHID ext ension
CONNECTbutton(fo r furth er deta ils ple ase see t he User 's manu al)
Shortpress:Acquire USBconnection in multicast mode
Lo ng pres s: Reset tofactory defaults
Video Strea m ID
0: R eceiv e strea m with Vi deo Str eam ID se t via soft ware
1-15:Recei ve stre am with f ixed Vi deo Str eam ID set b y the swi tch
Front LEDs
POWER
OFF:No power
Bl inkin g: Booting
Co ntinu ous: Power connected
VIDEO
OFF:Noconnection with ENCODER
Bl inkin g: Conn ected t o ENCOD ER, no vi deo out put
Continuous : Conne cted toENC ODER , vid eo ou tput
USB
OFF:NoUSB co nnect ion
Continuous:USB conne ction a quire d
VINX-110-HDMI-DEC
HDMIOUTPUT
CONNECT
POWER
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
1234
8-4-2-1
DECODER
16-port L3 Switch
VINX-120-HDMI-ENC
WiFi Router
Video Wall
VINX-120-HDMI-ENC
VINX-120-HDMI-ENC
VINX-120-HDMI-ENC
HDMI
(localout)
MODE
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
12 3 4
8-4-2-1
ENCODER
2-outputencoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
MODEb utton ( for fur ther de tails p lease s ee the Us er's man ual)
Shortp ress : Togglebetween bestvideo quality and adaptivedata rate
Lo ng pres s: Rese t to fact ory def aults
Video Strea m ID
0: T ransm it stre am with V ideo Str eam ID se t via sof tware
1-15:Transm it stre am with f ixed Vi deo Str eam ID se t by the sw itch
Front LEDs
POWER
OFF:No power
Blinking: Booting
Continuous: Powerconnected
VIDEO
OFF:No conne ction w ith DEC ODER
Bl inkin g: Conn ected t o DECOD ER, no vi deo out put
Continuous:Connec ted to DE CODER , video s ignal d etect ed on HDM I input
POWERandVIDEO
Blinking: Vi deo Str eam ID co nflic t in the ne twork
VINX-120-HDMI-ENC
HDMI
(localout)
MODE
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
12 3 4
8-4-2-1
ENCODER
2-outputencoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
MODEb utton ( for fur ther de tails p lease s ee the Us er's man ual)
Shortpress:Togglebetween best video qualityand adaptive data rate
Long press:Re set to fa ctory d efaul ts
Video Strea m ID
0: T ransm it stre am with V ideo Str eam ID se t via sof tware
1-15:Transm it stre am with f ixed Vi deo Str eam ID se t by the sw itch
FrontLEDs
POWER
OFF:Nop ower
Bl inkin g: Boot ing
Co ntinu ous: Power connected
VIDEO
OFF:No conne ction w ith DEC ODER
Bl inkin g: Conn ected t o DECOD ER, no vi deo out put
Continuous:Connec ted to DE CODER , video s ignal d etect ed on HDM I input
POWERandVIDEO
Blinking: Vi deo Str eam ID co nflic t in the ne twork
VINX-120-HDMI-ENC
HDMI
(localout)
MODE
VIDEO
USB
1GbELAN
(AVINPUT)
VIDEO
STREAMID
ON DIP
LINK ACT.
12 3 4
8-4-2-1
ENCODER
2-outputencoder with HDMI connector
HDMI1.4
Infrapor t
BidirectionalRS-232
USBHID ext ension
MODEb utton ( for fur ther de tails p lease s ee the Us er's man ual)
Shortp ress : Toggle be tween b est vid eo qual ity and a dapti ve data r ate
Lo ng pres s: Rese t to fact ory def aults
VideoStreamID
0: T ransm it stre am with V ideo Str eam ID se t via sof tware
1-15:Transm it stre am with f ixed Vi deo Str eam ID se t by the sw itch
Front LEDs
POWER
OFF:No power
Bl inkin g: Booting
Co ntinu ous: Power connected
VIDEO
OFF:Noconnection with DECODER
Bl inkin g: Conn ected t o DECOD ER, no vi deo out put
Continuous:Connec ted to DE CODER , video s ignal d etect ed on HDM I input
POWER and VID EO
Blinking:Video Str eam ID co nflic t in the ne twork
VINX-120-HDMI-ENC
LCD 1 LCD 2 LCD 3
Workstation 1
VINX-110AP
-HDMI-DEC
1-outputdecoder with HDMI connector
HDMI1.4
Infrapor t
Bidirectional RS-232
USBHID ext ension
CONNECTbutton(fo r furth er deta ils ple ase see t he User 's manu al)
Shortpress:Acq uire US B conne ction i n multi cast mod e
Lo ng pres s: Reset tofactory defaults
Video Strea m ID
0: R eceiv e strea m with Vi deo Str eam ID se t via soft ware
1-15:Recei ve stre am with f ixed Vi deo Str eam ID set b y the swi tch
FrontLEDs
POWER
OFF:No power
Bl inkin g: Boot ing
Co ntinu ous: Power connected
VIDEO
OFF:No connection with ENCODER
Bl inkin g: Conn ected t o ENCOD ER, no vi deo out put
Continuous:Connec ted to EN CODER , video o utput
USB
OFF:NoUSB connection
Continuous:USBconnection aquired
VINX-110AP-HDMI-DEC
HDMIOUTPUT
SFP
POWER
VIDEO 1GbELAN
(AVINPUT)
LINK ACT.
DECODER
DCIN
AUDIO
OUT
AUDIO
IN
UNICAST
MODE
ONLY
12V1A
DECODER
HD
display
Video Wall Player
PC 1
PC 2
PC 3
Tablet Control
RAP-B511-EU-K
VINX-120-HDMI-DEC
Remote Powering Remote Powering
ConditionsActions
Button Process SourceSwitching
SchedulingDisplay / Projector On / Off
Volume
1. Introduction RAP-B511 series
Meeting Room Application Example
Lights
Relay Box
RAP-B511-EU-K
Occupancy
Sensor
HDMIOUT
AUDIOOUT
SIGNAL HDCP
2
HDMIOUT
SIGNAL HDCP
1
HDMIIN
SIGNAL
1HDMIIN
SIGNAL
2HDMIIN
SIGNAL
3HDMIIN
SIGNAL
4
PIN:2mm
12VDC
1.5A---
_
HDMIEMBEDDID
ANALOGIN
ANALOGIN
HDMIEMBEDDID
HDMIEMBEDDID
HDMIEMBEDDID
ANALOGIN
ANALOGIN
AUDIO
SELECT
VIDEO
SELECT
HDMIOUT 1HDMIOUT 2
FrontLEDs
LIVE
AUDIOOUT
O1AUTO
Fastblinking (0.5 sec): Firmware upgrade mode
ON:Powered but no operation
OFF:No power
OFF:Embedded audio not present for de-embedding
Blinking(1 sec): Normal operation
Blinking:Audio format not supported for de-embedding
ON:Audio de-embedded
ON:Autoselect enabled on Output 1
O2AUTO
INPUTSELECT LEDs
ON- GREEN: Input selected, signal present,
originalaudio
ON- ORANGE: Input selected, signal present,
originalaudio replaced by analog audio in
RearLEDs
HDMIInputs:
HDMIOutputs:
ON:Signal present on input
SIGNAL
SIGNAL
OFF:Signal not present on input
Blinking:Input selected, signal not present
ON:Signal present
OFF:Signal not present or muted
HDCP
OFF:Output signal not HDCP encrypted
Blinking:Non HDCP capable device connected,
encryptedsignal replaced with red screen
ON:Output signal HDCP encrypted
ON:Autoselect enabled on Output 2
TPSIN
HDMIIN
HDMIIN
HDMIIN
AUTOSELECT
2
3
4
1
AUDIO
SELECT
Madein EU, Hungary
RoHS
Forbest performance use AWG23
CAT6orCAT7 SFTP cable
Devicecan be remote powered over TPS link with PoE
(IEEE802.3af)
Sn:
MMMMXX44xx22--HHDDMMII
4x2Matrix Switcher with TPS and HDMI intups Audio embedding and de-embedding
MMX4x2-HDMI
TBX-M210-K
Audio Amplifier
CATx
HDMI
Analog audio
GPIO
Monitor
PC
Laptop
ConditionsActions
Button ProcessSource Switching
SchedulingDisplay / Projector On / Off
Occupancy SensorLamp On / Off
Volume
Conference Room Application Example
ConditionsActions
Button Process SourceSwitching
SchedulingDisplay / Projector On / Off
Occupancy Sensor Lamp On / Off
Screen Up / Down
Volume
Madein EU, Hungary
50/60Hz 1.4-0.85A
100-240VAC
Sn:
Reset
3
4
RXTXRX TX
2 1
TXTX
4RS232
2 1
3
MICIN
AUDIOOUT
AUDIOIN
65
IIRROOUUTT
TPS+PoEOUT1 TPS+PoEOUT2
TPS+PoEIN1 TPS+PoEIN2 TPS+PoEIN3 TPS+PoEIN4
MMx8x4-HT420M
Lights Relay Box
UMX-TPS-TX140
TBX-M210-K
RAP-B511-EU-K
Remote Powering
CEC CEC
Laptop
Motorized Screen
Occupancy
Sensor
Monitor
Audio Amplifier
PC
Projector
CATx
RS-232
HDMI
Analog audio
VGA
DVI
Relay
GPIO
AUDIO1IN
VIDEO AUDIO
INPUTSTATUS
RESET
Audio1
HDMI
DP
DVI-D
HDCP
Autoselect
DVI-AVideo
Audio2
VGA
HDMI
DP
DVI-D
3DPIN
2
VIDEO
SELECT
AUDIO
SELECT
SHOW
ME
HDMI-TPS-RX97
2. Installation RAP-B511 series
Labels
and labels support to identify the customized button function.
Labels for button caps of the RAP-B511 series
PROJ
ON / OFF
SYSTEM
ON / OFF
PC
HDMI
DOC
CAM
VOL
UP
VOL
DOWN
VOL
MUTE WIRELESS APPLE
TV
BLACK
SCREEN
BLANK /
AV MUTE
HDMI1
CAMERA BLURAY MEDIA
PLAYER
ROOM
PC
WALL
PLATE
VIDEO
CONF
LECTERN
PC
HDMI2 AUTO
SOURCE INPUT1 INPUT2 INPUT3 INPUT4
PC1 PC2 LAPTOP LAPTOP1 LAPTOP2 VGA DP
LIGHTS
ON / OFF
LIGHTS
ON
LIGHTS
OFF
DISPLAY
1
DISPLAY
2
SYSTEM
ON
SYSTEM
OFF
PROJ
ON
PROJ
OFF
DISPLAY
ON / OFF
DISPLAY
ON
DISPLAY
OFF
SCREEN
UP
SCREEN
DOWN
2
Installation
The chapter is about the installation of the device and connecting to other
appliances, presenting also the mounting options and further assembly steps:
Mounting Options
Compatible Outlet Box Types
The room automation panel can be easily mounted into an industrial
Model name refers to the box type, see the recommended box types
for the models in the table below:
Model Outlet box type RAP-B511
RAP-B511-EU
RAP-B511-US
Double US wall box
Outlet Box, 2-Gang,
INFO: The outlet box is not supplied in the mounting kit. Please
The caps of the buttons are supplied separately with the product in a
plastic bag. Select the desired label and insert it as shown in attached
Step 1. Insert the label.
Step 2. Place the cap and pay
attention to the nut; the
direction of the buttons are
different, thus, certain caps
DISPLAY
ON
1
2
Ý
Ý
Ý
2. Installation RAP-B511 series
Mounting RAP-B511-EU into the Outlet Box
Step 1. Pull apart the from the Button panel by your hand (no special tool needed).
Step 2. Place two screws (marked with red color) or four screws (marked with yellow color) over the holes.
Front plate
Button panel
Button panel
Step 3. Insert the Button panel into the Outlet box and position it to get the holes aligned.
Step 4. Fasten the front side of the device to the Outlet box
Step 5. Place back the to the Button panel.
Button panel
Outlet box
Front plate
Button panel
2. Installation RAP-B511 series – User's Manual 11
Mounting RAP-B511-UK into the Outlet Box
Step 1. Pull apart the from the RAP-B511-UK by your hand (no special tool needed).
Step 2. Place four screws (marked with yellow) over the holes.
RAP-B511-UK
Front plate
RAP-B511-UK
Step 3. Insert the RAP-B511-UK into the Outlet box and position it to get the holes aligned.
Step 4. Fasten the front side of the device to the Outlet box
Step 5. Place back the to the RAP-B511-UK
RAP-B511-UK
Outlet box
RAP-B511-UK
Front plate
2. Installation RAP-B511 series – User's Manual 12
Mounting RAP-B511-US into the Outlet Box
Step 1. Pull apart the from the RAP-B511-US by your hand (no special tool needed).
Step 2. Place four screws (marked with yellow) over the holes.
Front plate
RAP-B511-US
RAP-B511-US
Step 3. Insert the RAP-B511-US into the Outlet box and position it to get the holes aligned.
Step 4. Fasten the front side of the device to the Outlet box
Step 5. Place back the to the RAP-B511-US
RAP-B511-US
Outlet box
Front plate
RAP-B511-US
2. Installation RAP-B511 series – User's Manual 13
Powering Options
and one Ethernet port can receive, and the other one can send power over the Ethernet line.
The room automation panel can be powered by any of the following ways:
POE OUT RJ45 connector to other PoE-compatible device.
The RAP-B511 can be powered remotely by a PoE-compatible power injector, like a PoE-compatible switch.
Local adaptor and
48V DC
Power
adaptor
MX-TPS2-IB-P
DC IN
8 CH TPS INPUT BOARD WITH POE
48V 5A
- +
Ethernet
TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4
8CH INPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN 1 IN 2 IN 3 IN 4
MX-TPS2-OB-S
48V5A
DC IN
8 CH TPS OUTPUT BOARD WITH DIGITALAUDIO
12V power on TPS connector. Only use with compatible devices!
12V power on TPS connector. Only use with compatible devices!
TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4
8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOGAUDIO
MX-HDMI-3D-OB-A
OUT 1 OUT 2 OUT 3
OUT 4
CATx
(TPS)
External
power supply
Power send
Power
send
RAP-B511-EU-K
PoE-compatible unit
RAP-B511-EU-K
Power send
RAP-B511-EU-K
PoE-compatible switch
Connecting Steps
Power adaptor
IR
GPIO
Power
RS-232
Smartphone
Relay box
Projector
LAN
LAN
Lightware device
Ethernet switch
ON OFF
AUTO
GPIO
RS-232
LAN
▪
▪
IR
Built-in infra detector is ready to receive any IR signal without user intervention.
Power
Powering Options section for the details.
3. Product Overview RAP-B511 series – User's Manual 14
3
Product Overview
The following sections are about the physical structure of the device, and the
connectors:
INFO: All the models have the same look and controls on the front panel, the only difference is the size
and the color of the enclosure.
INFO: The labels of the buttons are just for illustration since the button caps are empty by default. The
user can insert the desired label from the attached sheet.
1Buttons
Blinking of the button and rotary LEDs three times means, that the front panel
functionality is locked. Unlocking is possible with
Reference section).
2Rotary
LEDs
Eight green-colored LEDs for giving feedback about the current position of the jog dial knob.
full bright As the jog dial is rotated right (and the volume increases), the LEDs
turn on one-by-one. One level means half bright. The picture on the
left shows that the volume is set 11.
half bright
off
3Rotary
knob
purposes by turning and clicking the knob.
4Mute LED It gives feedback about the mute status of the volume. It can be toggled on and off by
pushing the rotary knob.
on The volume is muted.
off The volume is unmuted.
blinking The device is in bootload mode. Press the rotary knob for 5 sec for
changing to the normal operation mode.
5IR detector Built-in IR eye to receive infra signal.
ON OFF
AUTO
4
1
32
5
Ý
Ý
Ý
3. Product Overview RAP-B511 series – User's Manual 15
After removing the front plate (no special tool needed, just pull apart
by hands), a USB connector, a reset button, and a live led can be seen.
1USB Port
2Reset Button Hidden button to restart the device.
3Live LED blinking The unit is powered and ready to use.
on
off The unit is NOT powered or out of operation.
Step 1. 5 seconds; all front panel LEDs
start to blink.
Step 2. Release the button, then press it 3 times
enabled.
Reset the Device
Step 1. 10 seconds.
Step 2. Release the buttons. The mute LED lights up when the device
restarts.
OFF
AUTO
3
2
1
Step 1. 10 seconds; after 5 seconds front
panel LEDs start to blink but keep the button pressed; the LEDs
start to blink faster 5 seconds later.
Step 2. Release the button, then press it 3 times quickly.
For more information about the factory default values, see the Factory
Default Settings section.
Entering Bootload Mode
the device cannot be switched to bootload mode automatically. In this
case, the device can be forced into bootload mode as follows:
Step 1. Make sure the device is powered off.
Step 2. Press and keep pressed the Rotary knob.
Step 3. Power on the RAP-B511 while the Rotary knob is being pressed. If the device is switched to bootload
mode the Mute LED is blinking quickly. Release the knob.
Firmware Upgrade chapter.
INFO: Press the rotary for 5 sec to switch the normal operation mode.
Rear View
1GPIO 4-pole Phoenix®
2RS-232 port 3-pole Phoenix®connector for bi-directional serial communication.
3DC Input
Phoenix®connector. For more information about the powering, see Powering Options
section.
4Ethernet
ports
Two RJ45 connectors for Ethernet communication. Both of them are PoE-compatible,
one is a PoE receiver, the other can send PoE.
TX
RX
48V
DC 1A
GPIO 3
GPIO 2
GPIO 1
POE OUT
POE IN
1
24
3
3. Product Overview RAP-B511 series
Electrical Connections
48V DC Connection
power connection.
Pin nr. Signal
1 +
2 -
2-pole Phoenix connector and plug pin assignments
RS-232 Connector
The device contains a 3-pole Phoenix connector which is designed for
RS-232 serial connection.
Pin nr. Signal
1 Ground
2 TX data
3 RX data
RS-232 connector pin assignments
RS-232 Output Voltage Levels
▪Logic low level: 3V .. 15V
▪Logic high level: -15V .. -3V
Compatible Plug Type
Phoenix®
Settings for Other
Interfaces section.
pin-out.
1 2
2 3
GPIO - General Purpose Input/Output Ports
RAP-B511 series contains a 4-pole Phoenix connector with three GPIO
pins, which operates at TTL digital signal levels and can be set to high
or low level (Push-Pull). The direction of the pins can be input or output
(adjustable). Voltage ranges for GPIO inputs are the following:
Input
voltage [V]
Output
voltage [V]
Max. output
current [mA]
Logical low level
Logical high level 2 - 5 4.5 - 5V
Pin nr. Level and
direction
1
2
3
Ground
GPIO connector and plug pin assignments
Compatible plug type
Phoenix®
USB Connector
Behind the front panel there is a standard USB mini-B
receptacle.
1 2 3
Control Ethernet Port
The room automation panel is supplied an RJ-45
functions.
Wiring of LAN Cables
Lightware recommends the termination of LAN cables on the basis of
8 1
1
8
Top
8
1
Bottom Side
Pin TIA/EIA T568 A Color and name TIA/EIA T568 B Color and name
1
2green solid orange solid
3
4blue solid blue solid
5
6orange solid green solid
7
8brown solid brown solid
RAP-B511 series – User's Manual 17
4
Device Concept
This chapter is guide for building a room automation system using the whole
functionality of the RAP-B511 series.
General Concept
Room automation panel is designed for advanced control functions. Industrial standard communication
interfaces (RS-232, Ethernet, GPIO, IR) ensure the compatibility with third-party units or Lightware products.
They make possible to automate the whole AV system in a huddle room.
or conditions) and the desired outputs (actions). These settings can be done from a computer using the
details see section).
Inputs may come from:
▪The Room Automation Panel by pushing (or releasing) the button, turning or pushing the rotary switch.
▪
▪Other incoming signals: detected IR codes, recognized RS-232 messages, GPIO level changes.
Outputs can be the followings:
▪Button LEDs of the Room Automation Panel.
▪
sending, GPIO output state changing.
Button LEDs
OUT: Off / LED Light
OUT: TCP/UDP message
sending
Ethernet
OUT: Serial message
sending
RS-232
OUT: Output level change
(high/ low)
GPIO
Buttons
IN: Button press,
button release
IN: Rotary turn,
rotary press
Rotary
IN: Local time
Real-Time Clock
IN: Detected IR hash
Infra
IN: RS-232 recognizer
RS-232
IN: Input level change
(high/ low)
GPIO
These settings are available both the Event manager and the UI Config menu, but
managing the configuration is highly recommended in the UI config menu.
These settings are available only in the Event manager.
LDC
UI Cong menu
Ý
Ý
Ý
Ý
Ý
RAP-B511 series
Summary of the button operation modes
Momentary Operation Mode
PRESS RELEASE PRESS RELEASE
interaction state true false true false
Toggle Operation Mode
PRESS RELEASE PRESS RELEASE
interaction state true true false false
Radio Group Operation Mode
PRESS RELEASE PRESS RELEASE
12 3
12 3
12 3
12 3
interaction state true false false true false false false true false false true false
the details in Buttons
section).
Interaction state
Changes /
not changes,
true / false
Momentary
Toggle
Radio Group
Operation modeUser interaction
Button press
Button release
Action
Executed
Not extecuted
Inputs 1. - User Interactions
The operation of the RAP-B511 series is based on user interactions such as button press, or turn the rotary.
These are the main triggers (or inputs) of the control functions. They can be quickly and easily customize
in of the
Buttons
Pressed and Released.
Operation mode is an attribution of the button, which declares the button
behavior when it is pressed or released. Three different operation modes
are available: momentary, toggle and radio group (1-5).
The chosen operation modeinteraction state changes when the button is pressed or released
(see the details about it in the table on the right). The true or false value of the interaction state triggers the
button LED function and the desired action.
Momentary operation mode
Simple button function, when the button is pressed, the action will be executed.
Example
Explanation
interaction state changes false.
Toggle operation mode
This button type toggles between two states.
Example: Turn on and off the light with one button.
Explanation
Radio group operation mode
groups are available, one group may contain max. 11 buttons.
Example: Select video input on a crosspoint or switcher. One input can be active at the same time.
Explanation
RAP-B511 series
Rotary
purposes, too.
Turning left and right the rotary
action will be executed.
The control command can be sent over RS-232 or Ethernet (in this case,
the IP address of the target device is needed).
LWR Volume Control Schema
about the compatibility table in section) and
Custom Volume Control Schema
Knob press Custom schema is loaded, press and
can be found in
see section).
Volume control
schema
LWR
Custom
Ethernet
RS-232
InterfaceUser interaction
Rotary turn
Rotary press
Action
Mute /unmute,
volume up /
volume down
Any action
Inputs 2. - Automation Options
The below-listed features give an opportunity to "automate" the control system, and the Room Automation
Panel reacts the inputs automatically, the user intervention is not necessary.
These inputs can be set as a condition in the Event Manager in the
They trigger the desired actions.
Real-Time Clock
The real-time clock feature supports to store the exact time in the device. The time can be programmed as
Local time elements (years, months, days, etc.) help to customize the proper timing of the actions.
device is not powered.
ATTENTION!
Real-Time Clock Settings
red
by the user, the others generated automatically.
Flowchart of the real-time clock conguration process
the details in Time SettingsTime Settings section).
Local Time
(RTC)
Universal Time
Coordinated (UTC)
Network Time
Protocol (NTP)
Source:
• DHCP server
• Local network (with
NTP server)
Source: NTP time
Source:
• NTP time
• Set the RTC manually
+ timezone setting
+ daylight saving
setting
Local Time
Elements
Source: RTC time
Years
Months
Days
Hours
Weekday
...
RAP-B511 series
RS-232 Recognizer
(delimiter) is arrived or the timeout elapsed after the last data. The last incoming serial data is stored and it
can trigger an action in Event Manager.
ATTENTION! The recognizer function works, when the operation mode of the RS-232 port is control or
command injection (in this case, one of the Ethernet socket have to be opened). For more details about
the operation modes see Serial Interface section.
RS-232 Recognizer Example
switch, the relay box sends an RS-232 status message to the RAP-B511 to inform, and that the lamp was
the relay box of the lamp. This example shows how to syncronize the same control function in the RAP with
an other device.
Step 1.
connected to the RS-232 recognizer.
Turn on the lamp
ON OFF
AUTO
Relay box Lamp
RAP-B511 Light switch
RS-232
User interaction
Button press 1.
Interaction state
TRUE
Result
The lamp is
turned on
Incoming
RS-232 message
‘the lamp is
turned on’
Send
RS-232 message
‘turn on
the lamp’
Turn off the lamp
:
Step 2. Select the Button1 and set the operation mode to Toggle
state to true. It happens automatically.
Step 3. TRUE feedbacks tab and click on the RS-232 message recognized
Ok to save.
Step 4. FALSE feedbacks tab and click on the RS-232 message recognized
Ok to save.
details in see Message recognizer
RS-232 Recognizer section).
section.
User interaction
Button press 2.
‘the lamp is
turned off’
Interaction state
FALSE
Result
The lamp is
turned off
Send
RS-232 message
‘turn off the
lamp’
Incoming
RS-232 message
This manual suits for next models
8
Table of contents
Popular Control Panel manuals by other brands
Johnson Controls
Johnson Controls FC-2000 Installing
CIAT
CIAT AQUACIAT CALEO CONNECT TOUCH instruction manual
BFT
BFT A-CT BOARD SW installation manual
Erreka
Erreka CLEVER03 Quick installation and programming guide
SJE Rhombus
SJE Rhombus 122 Installation and operation manual
Danfoss
Danfoss OPX Series user manual
Carrier
Carrier INFINITY ZONING CONTROL installation instructions
Schaudt
Schaudt LT 100 operating instructions
SJE Rhombus
SJE Rhombus 123 Installation Instructions and Operation/Troubleshooting Manual
WABCO
WABCO SMARTBOARD manual
Helios
Helios KWL-FB Installation and operating instructions
AKO
AKO PROPlus 3PH Series quick guide