Paradox MG5000 Operating instructions

32-Zone Wireless Transceiver Control Panel
MG5000 V1.4
Programming Guide
We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit
www.paradox.com and send us your comments.

Installer Quick Menus
Zones
Keypad Zone Number Assignment (Keypad Programming)
Delays
Time and Date
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. LED/key on = programmed zone.
[MAINTENANCE CODE]may also be used.
2[ZONE NUMBER]MG32LRF/MG32LED = 2 digits: 01 to 32
MG10LEDV/H = 1 digit: 1 to 0(10)
3[LEARN ZONE]* Open/close cover or press learn/tamper switch or press [ENTER] for hardwired panel/key-
pad zone.* To erase a programmed zone, press the [SLEEP] key for 3 seconds.
4[ZONE TYPE]00 = Disabled 08 = Instant 15 = 24Hr. Buzzer
01 = Entry Delay 1 09 = Instant/Stay 16 = 24Hr. Burglary
02 = Entry Delay 2 10 = Instant/Stay/Sleep 17 = 24Hr. Hold-Up
03 = Entry Delay 1/Stay/Sleep 11 = Instant Fire 18 = 24Hr. Gas
04 = Entry Delay 2/Stay/Sleep 12 = Delayed Fire 19 = 24Hr. Heat
05 = Follow 13 = Instant Fire (silent) 20 = 24Hr. Water
06 = Follow/Stay 14 = Delayed Fire (silent) 21 = 24Hr. Freeze
07 = Follow/Stay/Sleep
5[1] and/or [2] +[ENTER]Assign the zone to one or both partitions and press [ENTER]. By default, all zones are
assigned to partition 1. Goes to next available zone.
Notes Partition 2 status LEDs display the signal strength of the selected wireless zone
(4 LEDs = best signal; 1 LED = weak signal; No LEDs = hardwired panel/keypad zone)
Step Action Details
1[ENTER] + [INSTALLER CODE][ARM] and [STAY]LEDs flash. [MAINTENANCE CODE]may also be used.
2Press and hold [](3sec) [ARM]and [STAY]LEDs turn on.
3[ZONE NUMBER] +[ENTER]* MG32LRF/MG32LED = 2 digits: 01 to 32
MG10LEDV/H = 1 digit: 1 to 0(10)
* To erase a keypad zone number, press [CLEAR], then [ENTER].
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[TBL]
3[1] = Entry Delay 1 (sec.)
[2] = Entry Delay 2 (sec.)
[3] = Exit Delay (sec.)
[4] = Bell Cut-Off (min.)
4[000] to [255] Enter a value between 000 and 255 (000 = default value).
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[TBL]
3[5]
4[HH:MM]Enter time. If HH = 13 or more, skip to step 6.
5[TIME FORMAT]Enter time format ([1] = 24hr; [2] = AM; [3] = PM).
6[YYYY/MM/DD]Enter date.

Walk Test Mode
Installer and Maintenance Codes
WinLoad
Monitoring Phone #
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[TBL]
3[6] Activates or deactivates Walk Test Mode.
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[TBL]
3[7] = Installer Code
[8] = Maintenance Code
4[CODE]* Enter 4- or 6-digit code.* To erase a code, press the [SLEEP] key for 3 seconds.
5[CONFIRM CODE]Re-enter 4- or 6-digit code.
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[TBL]
3[9]
4[PHONE #] +[ENTER]* Enter PC phone # (up to 32 digits) and press [ENTER].* To erase WinLoad phone #, panel
ID, and PC password, press the [SLEEP] key for 3 seconds.
5[PANEL ID]Enter 4-digit Panel ID
6[PC PASSWORD]Enter 4-digit PC Password
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[MEM]
3[1]
4[PHONE #] +[ENTER]* Enter monitoring station phone # (up to 32 digits) and press [ENTER].* To erase monitor-
ing phone #, reporting format, and partition account #s, press the [SLEEP] key for 3 sec-
onds.
5[PARTITION 1 ACCOUNT #]
6[1] = CID
[2] = SIA
7[PARTITION 2 ACCOUNT #]

Communicator
Cancel Communication
PGMs
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[MEM]
3[2] = Backup Phone #
[3] = Personal Phone #1
[4] = Personal Phone #2
[5] = Personal Phone #3
[6] = Personal Phone #4
[7] = Personal Phone #5
[8] = Pager #
4[PHONE #] +[ENTER]* Enter phone # (up to 32 digits) and press [ENTER]. Goes to next phone#, or go to step 5
if [8] = Pager # was selected. To erase a phone number.pager message, press the
[SLEEP] key for 3 seconds.
5[MESSAGE] +[ENTER]Step 5 for Pager # only. Enter pager message and press [ENTER].
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. [MAINTENANCE CODE]may also be used.
2[MEM]
3[9] Cancels all communication with WinLoad.
Step Action Details
1[]+ [INSTALLER CODE]The [ ] key will flash. LED/key on = programmed PGM.
[MAINTENANCE CODE]may also be used.
2[BYP]
3[PGM NUMBER]MG32LRF/MG32LED = 2 digits: 01 to 16
MG10LEDV/H = 1 digit: 1 to 0(10)
4[LEARN PGM]* Open/close cover or press [ENTER] for hardwired PGM.* To erase a PGM, press the
[SLEEP] key for 3 seconds.
5[PGM TYPE]1 = Follow Button or 5 = Follow Bell
2 = Follow Button or 6 = Follow Arm
3 = Follow Zone 7 = Follow Stay arm
4 = Follow Alarm 8 = Follow Sleep arm
6 If PGM type is 1, 2, 3, or 4
[ACTIVATION DELAY]1 = Follow 4 = 15 seconds 7 = 5 minutes 2 = 1 second 5 = 30 seconds 8 = 15 minutes
3 = 5 seconds 6 = 1 minute 9 = 30 minutes
If PGM type is 5
Goes to next available PGM.
If PGM type is 6, 7, or 8
[1] and/or [2] +[ENTER]If system is partitioned, select partition(s) and press [ENTER].
Goes to next available PGM.
7 If PGM type is 1, or 2
[2-DIGIT REMOTE CONTROL #] 01 to 32; 00 = all remote controls. Goes to next available PGM.
If PGM type is 3
[2-DIGIT ZONE #] 01 to 32; 00 = all zones.
Goes to next available PGM.
If PGM type is 4
[1] and/or [2] +[ENTER]If system is partitioned, select partition(s) and press [ENTER].
Goes to next available PGM.

Magellan 5
Table of Contents
Installer Quick Menus............................................ 2
Zones .................................................................................. 2
Keypad Zone Number Assignment (Keypad Programming) 2
Delays ................................................................................. 2
Time and Date .................................................................... 2
Walk Test Mode .................................................................. 3
WinLoad .............................................................................. 3
Monitoring Phone # ............................................................. 3
Communicator...................................................................... 4
Cancel Communication ....................................................... 4
PGMs .................................................................................. 4
Things You Should Know..................................... 6
About This Programming Guide........................................... 6
Conventions......................................................................... 6
To Reset the Panel to Default.............................................. 6
Installer Code (Default: 0000 / 000000)............................... 6
Maintenance Code (Default: 1111 / 111111)....................... 6
System Master Code (Default: 1234 / 123456).................... 6
Entering Programming Mode ............................... 6
Zone Programming................................................ 7
Zone Definition Status ......................................................... 8
Zone Recognition................................................................. 8
Zone Timers......................................................................... 8
Wireless Transmitter Serial Number.................................... 9
Wireless Transmitter Signal Strength .................................. 9
Zone Reporting Codes (Default = FF) ............................... 10
Programmable Output Programming ................ 11
Programmable Output Activation/Deactivation Events...... 11
Event Description............................................................... 12
Programmable Output Options.......................................... 15
Programmable Output Delays............................................ 16
PGMs Serial Number......................................................... 16
Wireless PGM Signal Strength.......................................... 17
PGM Recognition............................................................... 17
Wireless Repeater Programming (MG-RPT1).... 18
Wireless Repeater Assignment.......................................... 18
Wireless Repeater Signal Strength.................................... 18
Wireless Repeater Options................................................ 18
Wireless Keypad Programming (MG32LRF) ..... 21
Automatic Wireless Keypad Assignment........................... 21
Standard Wireless Keypad Assignment............................. 21
Wireless Keypad Signal Strength ...................................... 21
Wireless Keypad Options................................................... 21
User Programming .............................................. 22
System Codes ................................................................... 22
User Code Options ............................................................ 22
User Reporting Codes (Default = FF)................................ 23
Remote Control (RC) User Assignment............................. 23
Remote Button Assignment............................................... 24
System Programming.......................................... 25
System Timers................................................................... 27
Daylight Savings Programming ......................... 27
Partition Programming........................................ 28
Partition Timers................................................................. 28
Communication Programming............................ 29
Communication Settings................................................... 30
Communication Timers..................................................... 31
Special Arming Report Codes (Default = FF).................... 31
Special Disarming Report Codes (Default = FF)............... 31
Special Alarm Report Codes (Default = FF)...................... 31
System Trouble Report Codes (Default = FF)................... 32
System Trouble Restore Report Code (Default = FF)....... 32
System Special Report Code (Default = FF)..................... 32
WinLoad Programming........................................ 33
WinLoad Options............................................................... 33
WinLoad Timers................................................................ 33
Other Settings and Modes................................... 33
Appendix 1: Ademco Contact ID Report Codes 34
Appendix 2: Automatic Report Code List.......... 36
Appendix 3: Data Entry & Display ...................... 38
Single Digit Data Entry Method......................................... 38
Feature Select Programming Method............................... 38
Decimal and Hexadecimal Values .................................... 38
Hardware Connections........................................ 39
Single Zone Inputs............................................................ 39
Advanced Technology Zone (ATZ) Connections .............. 40
Connecting Fire Circuits and PGMs.................................. 41
Alarm Relay and PGM Connections ................................. 41
AC Power & Backup Battery Connections........................ 41
Connecting Magellan to WinLoad..................................... 42
Updating Firmware Using WinLoad .................................. 42
8x10” Metal Box Installation.............................................. 43
11x11” Metal Box Installation............................................ 43
MG5000 PCB Layout ........................................................ 44
Trouble Display .................................................... 45
Installer Function Keys........................................ 45

6Programming Guide
Things You Should Know
About This Programming Guide
This programming guide should be used in conjunction with the MG5000 Reference & Installation Manual which can be downloaded
from our website at paradox.com. Use this guide to record the settings programmed for this console.
Conventions
To Reset the Panel to Default
Press and hold the RESET switch for five seconds. The STATUS LED will start flashing. Within 2 seconds of this flashing, press the
reset switch again. The panel will reset to default and restart. However, this will not clear a bus module trouble. To do so, see section
[955].
To reset the panel to default in section programming, go to section [950] and press [ENTER].
Installer Code (Default: 0000 / 000000)
The Installer code is used to enter programming mode, which allows you to program all the features, options and commands of the
MG5000 except user codes. The Installer code can be 4 or 6 digits in length (see section [701] option [1] on page 25) where each digit
can be any value from 0 to 9. See section 17[397] on page 22 to change the default code.
Maintenance Code (Default: 1111 / 111111)
The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all
the features, options and commands except for the MG5000’s communication settings (sections [395], [397], [398], [815], [816],
[817], [910], and [911]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length (see section [701] option [1]
on page 25) where each digit can be any value from 0 to 9. See section [398] on page 22 to change the default code.
System Master Code (Default: 1234 / 123456)
With the System Master code a user can use any arming method and can program user codes. The System Master code can be 4 or
6 digits in length (see section [701] option [1] on page 25), where each digit can be any digit from 0 to 9. The System Master code can
be changed by the Installer or Maintenance code. See section [399] on page 22 to change this default code.
Entering Programming Mode
Use the keypad to access the MG5000’s installer programming mode. To access programming mode:
1. Press [ENTER]
2. Enter your [INSTALLER CODE]or [MAINTENANCE CODE]
3. Enter 3-digit [SECTION]you wish to program
4. Enter required [DATA]
This symbol designates a warning or important information.
This symbol designates a suggestion or reminder.
This symbol designates a reference to the Installer Quick Menu or Master Quick Menu.
WARNING: This equipment must be installed and maintained by qualified service personnel only.

Magellan 7
Zone Programming
Section Description Zone Definition Partition Assignment Zone Options
[001] = Zone 1: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[002] = Zone 2: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[003] = Zone 3: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[004] = Zone 4: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[005] = Zone 5: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[006] = Zone 6: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[007] = Zone 7: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[008] = Zone 8: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[009] = Zone 9: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[010] = Zone 10: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[011] = Zone 11: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[012] = Zone 12: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[013] = Zone 13: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[014] = Zone 14: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[015] = Zone 15: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[016] = Zone 16: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[017] = Zone 17: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[018] = Zone 18: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[019] = Zone 19: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[020] = Zone 20: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[021] = Zone 21: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[022] = Zone 22: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[023] = Zone 23: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[024] = Zone 24: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[025] = Zone 25: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[026] = Zone 26: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[027] = Zone 27: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[028] = Zone 28: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[029] = Zone 29: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[030] = Zone 30: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[031] = Zone 31: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
[032] = Zone 32: _________________________ _____/_____ _____________ 1 2 3 4 5 6 7 8
Zone Definitions
00 = Zone disabled
01 = Entry Delay 1
02 = Entry Delay 2
03 = Entry Delay 1/Stay/Sleep
04 = Entry Delay 2/Stay/Sleep
05 = Follow
06 = Follow /Stay
07 = Follow/Stay/Sleep
08 = Instant
09 = Instant/Stay
10 = Instant/Stay/Sleep
11 = Instant Fire
12 = Delayed Fire
13 = Instant Fire Silent
14 = Delayed Fire Silent
15 = 24Hr. Buzzer
16 = 24Hr. Burglary
17 = 24Hr. Hold-up
18 = 24Hr. Gas
19 = 24Hr. Heat
20 = 24Hr. Water
21 = 24Hr. Freeze
Zone Options
[1] = Auto-zone Shutdown
[2] = Bypassable Zone
[3] = RF Supervision
[4] [5]
OFF OFF Audible Alarm
OFF ON Pulsed Alarm
ON OFF Silent Alarm
ON ON Report Only
[6] = Intellizone
[7] = Delay alarm transmission
[8] = Force Zone
Partition Assignment
[1]- Partition 1
[2]- Partition 2
[3]- Both partitions
For UL installation, fire zone cannot be
bypassable. Turn off zone option [2].
Refer to the Installer Quick Menu on the inside cover
for zone programming/keypad zone programming.

8Programming Guide
Zone Definition Status
Zone Recognition
If a zone is already programmed and you assign a device to the same zone, a wireless zone will overwrite a keypad/
hardwire zone, and a keypad zone will overwrite a hardwire zone.
Zone Timers
Stay/ Sleep Alarm Delay -
Section [720] is 0 Stay/ Sleep Alarm Delay - Section [720] is not 0
Zone
Definition Description Stay Arm Sleep Arm Fully Arm Stay Arm Sleep Arm Fully Arm
01 Entry Delay 1 As is As is As is As is As is As is
02 Entry Delay 2 As is As is As is As is As is As is
03 Entry Delay1/Stay/Sleep Not Armed Not Armed Entry Delay 1 Not Armed Not Armed Entry Delay 1
04 Entry Delay2/Stay/Sleep Not Armed Not Armed Entry Delay 2 Not Armed Not Armed Entry Delay 2
05 Follow (Entry Delay/Instant) As is As is As is Follow (Entry
Delay/SleepDelay) Follow (Entry Delay/SleepDelay) Follow (Entry Delay/Instant)
06 Follow/Stay Not Armed Follow (Entry
Delay/Instant) Follow (Entry Delay/Instant) Not Armed Follow (Entry Delay/SleepDelay) Follow (Entry Delay/Instant)
07 Follow/Stay/Sleep Not Armed Not Armed Follow (Entry
Delay/Instant) Not Armed Not Armed Follow (Entry Delay/Instant)
08 Instant As is As is As is Sleep Delay Sleep Delay Instant
09 Instant/Stay Not Armed Instant Instant Not Armed Sleep Delay Instant
10 Instant/Stay/Sleep Not Armed Not Armed Instant Not Armed Not Armed Instant
11 to 21 Instant Fire to 24Hr.
Freeze As is As is As is As is As is As is
Wireless:
Overwrites a keypad or hardwire zone assigned to
same zone.
Keypad:
Overwrites a hardwire zone assigned to same
zone.
Hardwire Panel Input
Zone 1 Yes Yes Yes (Panel Input 1)
Zone 2 Yes Yes Yes (Panel Input 2)
Zone 3 Yes Yes Yes (Panel Input 1with ATZ)
Zone 4 Yes Yes Yes (Panel Input 2 with ATZ)
Zone 5 to 32 Yes Yes No
Section Data Description
[041] = Zone 1 (Z1): ____/____/____ (000 to 255) x 10ms Hardwire Zone 1 Speed (Default 060)
[042] = Zone 2 (Z2): ____/____/____ (000 to 255) x 10ms Hardwire Zone 2 Speed (Default 060)
[043] = Zone 3 (Z1 with ATZ): ____/____/____ (000 to 255) x 10ms Hardwire Zone 3 Speed (Default 060)
[044] = Zone 4 (Z2 with ATZ): ____/____/____ (000 to 255) x 10ms Hardwire Zone 4 Speed (Default 060)

Magellan 9
Wireless Transmitter Serial Number
To delete a wireless transmitter, enter [000000] in its respective section.
To view the serial number display, refer to section [960].
For automatic assignment, press the wireless transmitter’s anti-tamper switch while in the respective section.
Refer to the Installer Quick Menu on the inside cover for transmitter assignment.
Wireless Transmitter Signal Strength
To view the wireless transmitter signal strength, press the wireless transmitter’s anti-tamper switch while in the respective
section.
Section Wireless Transmitter Serial Number Section Wireless Transmitter Serial Number
[061] Zone 1: ____/____/____/____/____/____ [077] Zone 17: ____/____/____/____/____/____
[062] Zone 2: ____/____/____/____/____/____ [078] Zone 18: ____/____/____/____/____/____
[063] Zone 3: ____/____/____/____/____/____ [079] Zone 19: ____/____/____/____/____/____
[064] Zone 4: ____/____/____/____/____/____ [080] Zone 20: ____/____/____/____/____/____
[065] Zone 5: ____/____/____/____/____/____ [081] Zone 21: ____/____/____/____/____/____
[066] Zone 6: ____/____/____/____/____/____ [082] Zone 22: ____/____/____/____/____/____
[067] Zone 7: ____/____/____/____/____/____ [083] Zone 23: ____/____/____/____/____/____
[068] Zone 8: ____/____/____/____/____/____ [084] Zone 24: ____/____/____/____/____/____
[069] Zone 9: ____/____/____/____/____/____ [085] Zone 25: ____/____/____/____/____/____
[070] Zone 10: ____/____/____/____/____/____ [086] Zone 26: ____/____/____/____/____/____
[071] Zone 11: ____/____/____/____/____/____ [087] Zone 27: ____/____/____/____/____/____
[072] Zone 12: ____/____/____/____/____/____ [088] Zone 28: ____/____/____/____/____/____
[073] Zone 13: ____/____/____/____/____/____ [089] Zone 29: ____/____/____/____/____/____
[074] Zone 14: ____/____/____/____/____/____ [090] Zone 30: ____/____/____/____/____/____
[075] Zone 15: ____/____/____/____/____/____ [091] Zone 31: ____/____/____/____/____/____
[076] Zone 16: ____/____/____/____/____/____ [092] Zone 32: ____/____/____/____/____/____
Section Section
[101] Zone 1 [117] Zone 17
[102] Zone 2 [118] Zone 18
[103] Zone 3 [119] Zone 19
[104] Zone 4 [120] Zone 20
[105] Zone 5 [121] Zone 21
[106] Zone 6 [122] Zone 22
[107] Zone 7 [123] Zone 23
[108] Zone 8 [124] Zone 24
[109] Zone 9 [125] Zone 25
[110] Zone 10 [126] Zone 26
[111] Zone 11 [127] Zone 27
[112] Zone 12 [128] Zone 28
[113] Zone 13 [129] Zone 29
[114] Zone 14 [130] Zone 30
[115] Zone 15 [131] Zone 31
[116] Zone 16 [132] Zone 32
Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)

10 Programming Guide
Zone Reporting Codes (Default = FF)
Refer to Decimal and Hexadecimal Values on page 38.
Section Alarm Alarm Restore Tamper Tamper Restore
[141] Zone 1: _____/_____ _____/_____ _____/_____ _____/_____
[142] Zone 2: _____/_____ _____/_____ _____/_____ _____/_____
[143] Zone 3: _____/_____ _____/_____ _____/_____ _____/_____
[144] Zone 4: _____/_____ _____/_____ _____/_____ _____/_____
[145] Zone 5: _____/_____ _____/_____ _____/_____ _____/_____
[146] Zone 6: _____/_____ _____/_____ _____/_____ _____/_____
[147] Zone 7: _____/_____ _____/_____ _____/_____ _____/_____
[148] Zone 8: _____/_____ _____/_____ _____/_____ _____/_____
[149] Zone 9: _____/_____ _____/_____ _____/_____ _____/_____
[150] Zone 10: _____/_____ _____/_____ _____/_____ _____/_____
[151] Zone 11: _____/_____ _____/_____ _____/_____ _____/_____
[152] Zone 12: _____/_____ _____/_____ _____/_____ _____/_____
[153] Zone 13: _____/_____ _____/_____ _____/_____ _____/_____
[154] Zone 14: _____/_____ _____/_____ _____/_____ _____/_____
[155] Zone 15: _____/_____ _____/_____ _____/_____ _____/_____
[156] Zone 16: _____/_____ _____/_____ _____/_____ _____/_____
[157] Zone 17: _____/_____ _____/_____ _____/_____ _____/_____
[158] Zone 18: _____/_____ _____/_____ _____/_____ _____/_____
[159] Zone 19: _____/_____ _____/_____ _____/_____ _____/_____
[160] Zone 20: _____/_____ _____/_____ _____/_____ _____/_____
[161] Zone 21: _____/_____ _____/_____ _____/_____ _____/_____
[162] Zone 22: _____/_____ _____/_____ _____/_____ _____/_____
[163] Zone 23: _____/_____ _____/_____ _____/_____ _____/_____
[164] Zone 24: _____/_____ _____/_____ _____/_____ _____/_____
[165] Zone 25: _____/_____ _____/_____ _____/_____ _____/_____
[166] Zone 26: _____/_____ _____/_____ _____/_____ _____/_____
[167] Zone 27: _____/_____ _____/_____ _____/_____ _____/_____
[168] Zone 28: _____/_____ _____/_____ _____/_____ _____/_____
[169] Zone 29: _____/_____ _____/_____ _____/_____ _____/_____
[170] Zone 30: _____/_____ _____/_____ _____/_____ _____/_____
[171] Zone 31: _____/_____ _____/_____ _____/_____ _____/_____
[172] Zone 32: _____/_____ _____/_____ _____/_____ _____/_____

Magellan 11
Programmable Output Programming
Programmable Output Activation/Deactivation Events
* Section [220] PGM 1 Activation Event default = (Option B Remote Assignment) Button pressed on Any remote/Any
partition. † Section [222] PGM 2 Activation Event default = (Option C Remote Assignment) Button pressed on Any remote/
Any partition. See Button Options Table on page 24
Section Event Group # Sub-Group # Partition # Default
[220] PGM 1: Activation Event (____/____) (____/____) (____/____) 08/99/99*
[221] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[222] PGM 2: Activation Event (____/____) (____/____) (____/____) 09/99/99†
[223] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[224] PGM 3: Activation Event (____/____) (____/____) (____/____) 00/00/00
[225] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[226] PGM 4: Activation Event (____/____) (____/____) (____/____) 00/00/00
[227] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[228] PGM 5: Activation Event (____/____) (____/____) (____/____) 00/00/00
[229] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[230] PGM 6: Activation Event (____/____) (____/____) (____/____) 00/00/00
[231] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[232] PGM 7: Activation Event (____/____) (____/____) (____/____) 00/00/00
[233] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[234] PGM 8: Activation Event (____/____) (____/____) (____/____) 00/00/00
[235] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[236] PGM 9: Activation Event (____/____) (____/____) (____/____) 00/00/00
[237] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[238] PGM 10: Activation Event (____/____) (____/____) (____/____) 00/00/00
[239] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[240] PGM 11: Activation Event (____/____) (____/____) (____/____) 00/00/00
[241] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[242] PGM 12: Activation Event (____/____) (____/____) (____/____) 00/00/00
[243] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[244] PGM 13: Activation Event (____/____) (____/____) (____/____) 00/00/00
[245] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[246] PGM 14: Activation Event (____/____) (____/____) (____/____) 00/00/00
[247] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[248] PGM 15: Activation Event (____/____) (____/____) (____/____) 00/00/00
[249] Deactivation Event (____/____) (____/____) (____/____) 00/00/00
[250] PGM 16: Activation Event (____/____) (____/____) (____/____) 00/00/00
[251] Deactivation Event (____/____) (____/____) (____/____) 00/00/00

12 Programming Guide
Event Description Event Group # Sub-group #
00 = Zone OK 01 to 32 = Zone number
99 = Any zone number
01 = Zone open
02 = Partition status 00 to 01= N/A
02 = Silent alarm
03 = Buzzer alarm
04 = Steady alarm
05 = Pulsed alarm
06 = Strobe
07 = Alarm stopped
08 = Squawk ON (Partition 1 only)
09 = Squawk OFF (Partition 1 only)
10 = Ground start (Partition 1 only)
11 = Disarm partition
12 = Arm partition
13 = Entry delay started
14 = Exit delay started
99 = Any partition status event
03 = Bell status (Partition 1 only) 00 = Bell OFF
01 = Bell ON
02 = Bell squawk arm
03 = Bell squawk disarm
99 = Any bell status event
06 = Non-reportable event 00 = Telephone line trouble
01 = [ENTER] / [CLEAR] / [ ] key was pressed (Partition 1 only)
02 = N/A
03 = Arm in stay mode
04 = Arm in sleep mode
05 = Arm in force mode
06 = Full arm when armed in stay mode
07 = PC fail to communicate (Partition 1 only)
08 = Utility Key 1 pressed (keys [1] and [2]) (Partition 1 only)
09 = Utility Key 2 pressed (keys [2] and [3]) (Partition 1 only)
10 = Utility Key 3 pressed (keys [4] and [5]) (Partition 1 only)
11 = Utility Key 4 pressed (keys [5] and [6]) (Partition 1 only)
12 = Utility Key 5 pressed (keys [7] and [8]) (Partition 1 only)
13 = Utility Key 6 pressed (keys [8] and [9]) (Partition 1 only)
14 = Tamper generated alarm
15 = Supervision loss generated alarm
16 = N/A
17 = N/A
18 = N/A
19 = N/A
20 = Full arm when armed in sleep mode
21 = Firmware upgrade (Partition 1 only)
99 = Any non-reportable event
07 = Remote control access 01 to 32 = Remote control number
99 = Any remote control number
08 = Button pressed on remote
(See button option “B” on page 24)
09 = Button pressed on remote
(See button option “C” on page 24)
10 = Button pressed on remote
(See button option “D” on page 24)
11 = Button pressed on remote
(See button option “E” on page 24)
12 = Cold start wireless zone 01 to 32 = Zone number
99 = Any zone number

Magellan 13
13 = Cold start wireless module (Partition 1 only) 01 to 16 = Output number
17 to 18 = Wireless repeater
19 to 22 = Wireless keypad
99 = Any output number
14 = Bypass programming 01 to 32 = User number
99 = Any user number
15 = User code activated output (Partition 1 only)
16 = Wireless smoke maintenance signal 01 to 32 = Zone number
99 = Any zone number
17 = Delay zone alarm transmission
18 = Zone signal strength weak 1 (Partition 1 only)
19 = Zone signal strength weak 2 (Partition 1 only)
20 = Zone signal strength weak 3 (Partition 1 only)
21 = Zone signal strength weak 4 (Partition 1 only)
24 = Fire Delay started 01 to 32 = Zone number
99 = Any zone number
25 to 26 = N/A
27 = Bus module event 00 = A bus module was added
01 = A bus module was removed
02 = 2-way RF Module Communication Failure
03 = 2-way RF Module Communication Restored
29 = Arming with user 01 to 32 = User number
99 = Any user number
30 = Special arming 00 = Auto-arming (on time/no movement)
01 = Late to close
02 = No movement arming
03 = Partial arming
04 = Quick arming
05 = Arming through WinLoad
99 = Any special arming
31 = Disarming with user 01 to 32 = User number
99 = Any user number
32 = Disarming after alarm with user
33 = Alarm cancelled with user
34 = Special disarming 00 = Auto-arm cancelled (on time/no movement)
01 = Disarming through WinLoad
02 = Disarming through WinLoad after alarm
03 = Alarm cancelled through WinLoad
04 = Paramedical alarm cancelled
99 = Any special disarming
35 = Zone bypassed 01 to 32 = Zone number
99 = Any zone number
36 = Zone in alarm
37 = Fire alarm
38 = Zone alarm restore
39 = Fire alarm restore
40 = Special alarm 00 = Panic non-medical emergency
01 = Panic medical (this panic alarm is not UL approved)
02 = Panic fire
03 = Recent closing
04 = Global shutdown
05 = Duress alarm
06 = Keypad lockout (Partition 1 only)
99 = Any special alarm event
41 = Zone shutdown 01 to 32 = Zone number
99 = Any zone number
42 = Zone tampered
43 = Zone tamper restore
Event Group # Sub-group #

14 Programming Guide
Refer to the Installer Quick Menu on the inside cover for alternate PGM programming.
44 = New trouble
(Partition 1 only except sub-group 07 = both partitions) 00 = N/A 01 = AC failure
02 = Battery failure
03 = Auxiliary current overload
04 = Bell current overload
05 = Bell disconnected
06 = Clock loss
07 = Fire loop trouble
08 = Fail to communicate to monitoring station telephone #1
09 = Fail to communicate to monitoring station telephone #2
10 = Fail to communicate to pager report
11 = Fail to communicate to voice report
12 = RF interference
99 = Any new trouble event
45 = Trouble restored 00 = Telephone line restored
01 = AC failure restore
02 = Battery failure restore
03 = Auxiliary current overload restore
04 = Bell current overload restore
05 = Bell disconnected restore
06 = Clock loss restore
07 = Fire loop trouble restore
12 = RF interference restore
99 = Any trouble restored event
46 = Bus/wireless module new trouble (Partition 1 only) 00 = Bus communication fault
01 = Tamper trouble
02 = Power fail
03 = Battery failure
99 = Any bus module new trouble event
47 = Bus/wireless module trouble restored (Partition 1 only) 00 = Bus communication fault restore
01 = Tamper trouble restore
02 = Power fail
03 = Battery failure
99 = Any bus module trouble restored event
48 = Special (Partition 1 only) 00 = System power up
01 = Reporting test
02 = WinLoad log on
03 = WinLoad log off
04 = Installer in programming mode
05 = Installer exited programming mode
06 = Maintenance in programming mode
07 = Maintenance exited programming mode
08 = Closing delinquency delay elapsed
99 = Any special event
49 = Low battery on zone 01 to 32 = Zone number
99 = Any zone number
50 = Low battery on zone restore
51 = Zone supervision trouble
52 = Zone supervision restore
53 = Wireless module supervision trouble (Partition 1 only)
54 = Wireless module supervision restore (Partition 1 only)
55 = Wireless module tamper trouble (Partition 1 only)
56 = Wireless module tamper restore (Partition 1 only)
01 to 16 = Output
17 to 18 = Wireless repeater
19 to 22 = Wireless keypad
57 = Non-medical alarm (paramedic) 01 to 32 = User number
99 = Any user number
58 = Zone forced 01 to 32 = Zone number
99 = Any zone number
59 = Zone included
Event Group # Sub-group #

Magellan 15
Programmable Output Options
Default:
Bold Section: PGM 1 [261] PGM 2 [262] PGM 3 [263] PGM 4 [264]
Option OFF ON OFF ON
OFF ON OFF ON
[1] PGM Base Time (Off=Sec; On=Min) NNNN
[2] PGM State (Off=N.O., On=N.C.) NNNN
[3] PGM Supervision NNNN
[4] PGM Activation Mode (Off=Steady, On=Pulse) NNNN
[5] PGM Pulse once every 30 seconds if armed NNNN
[6] PGM Pulse on any alarm NNNN
[7] PGM Pulse on any alarm -
OFF= Partition 1 On= Partition 2 NNNN
[8] N/A N/A N/A N/A N/A N/A N/A N/A N/A
Default:
Bold Section: PGM 5 [265] PGM 6 [266] PGM 7 [267] PGM 8 [268]
Option OFF ON
OFF ON OFF ON OFF ON
[1] PGM Base Time (Off=Sec.; On=Min.) NNNN
[2] PGM State (Off=N.O., On= N.C.) NNNN
[3] PGM Supervision NNNN
[4] PGM Activation Mode (Off=Steady, ON=Pulse) NNNN
[5] PGM Pulse once every 30 seconds if armed NNNN
[6] PGM Pulse on any alarm NNNN
[7] PGM Pulse on any alarm -
OFF= Partition 1 On= Partition 2 NNNN
[8] N/A N/A N/A N/A N/A N/A N/A N/A N/A
Default:
Bold Section: PGM 9 [269] PGM 10 [270] PGM 11 [271] PGM 12 [272]
Option OFF ON
OFF ON OFF ON OFF ON
[1] PGM Base Time (Off=Sec; On=Min) NNNN
[2] PGM State (Off=N.O., On=N.C.) NNNN
[3] PGM Supervision NNNN
[4] PGM Activation Mode (Off=Steady, On=Pulse) NNNN
[5] PGM Pulse once every 30 seconds if armed NNNN
[6] PGM Pulse on any alarm NNNN
[7] PGM Pulse on any alarm -
OFF= Partition 1 On= Partition 2 NNNN
[8] N/A N/A N/A N/A N/A N/A N/A N/A N/A

16 Programming Guide
Programmable Output Delays
PGMs Serial Number
To delete a wireless PGM, enter [000000] in its respective section.
To view the serial number display, refer to section [960].
For automatic assignment, press the PGM’s anti-tamper switch while in the respective section.
Refer to the Installer Quick Menu on the inside cover for alternate PGM programming.
Default:
Bold Section: PGM 13 [273] PGM 14 [274] PGM 15 [275] PGM 16 [276]
Option OFF ON OFF ON OFF ON OFF ON
[1] PGM Base Time (Off=Sec; On=Min) NNNN
[2] PGM State (Off=N.O., On=N.C.) NNNN
[3] PGM Supervision NNNN
[4] PGM Activation Mode (Off=Steady, On=Pulse) NNNN
[5] PGM Pulse once every 30 seconds if armed NNNN
[6] PGM Pulse on any alarm NNNN
[7] PGM Pulse on any alarm -
OFF= Partition 1 On= Partition 2 NNNN
[8] N/A N/A N/A N/A N/A N/A N/A N/A N/A
Section Data Description
[281]= PGM 1: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 1 Delay (Default 005)
[282]= PGM 2: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 2 Delay (Default 005)
[283]= PGM 3: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 3 Delay (Default 005)
[284]= PGM 4: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 4 Delay (Default 005)
[285]= PGM 5: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 5 Delay (Default 005)
[286]= PGM 6: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 6 Delay (Default 005)
[287]= PGM 7: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 7 Delay (Default 005)
[288]= PGM 8: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 8 Delay (Default 005)
[289]= PGM 9: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 9 Delay (Default 005)
[290]= PGM 10: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 10 Delay (Default 005)
[291]= PGM 11: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 11 Delay (Default 005)
[292]= PGM 12: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 12 Delay (Default 005)
[293]= PGM 13: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 13 Delay (Default 005)
[294]= PGM 14: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 14 Delay (Default 005)
[295]= PGM 15: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 15 Delay (Default 005)
[296]= PGM 16: ___/___/___ ( 000 to 255 x 1 sec./mins.) PGM 16 Delay (Default 005)
Section Wireless PGM Serial Number Section Wireless PGM Serial Number
[301]= PGM 1: ____/____/____/____/____/____ [309]= PGM 9: ____/____/____/____/____/____
[302]=PGM 2: ____/____/____/____/____/____ [310]=PGM 10: ____/____/____/____/____/____
[303]= PGM 3: ____/____/____/____/____/____ [311]=PGM 11: ____/____/____/____/____/____
[304]=PGM 4: ____/____/____/____/____/____ [312]=PGM 12: ____/____/____/____/____/____
[305]=PGM 5: ____/____/____/____/____/____ [313]=PGM 13: ____/____/____/____/____/____
[306]= PGM 6: ____/____/____/____/____/____ [314]=PGM 14: ____/____/____/____/____/____
[307]= PGM 7: ____/____/____/____/____/____ [315]= PGM 15: ____/____/____/____/____/____
[308]=PGM 8: ____/____/____/____/____/____ [316]=PGM 16: ____/____/____/____/____/____

Magellan 17
Wireless PGM Signal Strength
To view the wireless PGM signal strength, press the wireless PGM’s anti-tamper switch while in the respective section.
PGM Recognition
A Wireless PGM module can be assigned to any PGM. It will work in parallel with the Control Panel Output.
Section Section
[321] PGM 1 Wireless PGM Signal Strength [329] PGM 9 Wireless PGM Signal Strength
[322] PGM 2 Wireless PGM Signal Strength [330] PGM 10 Wireless PGM Signal Strength
[323] PGM 3 Wireless PGM Signal Strength [331] PGM 11 Wireless PGM Signal Strength
[324] PGM 4 Wireless PGM Signal Strength [332] PGM 12 Wireless PGM Signal Strength
[325] PGM 5 Wireless PGM Signal Strength [333] PGM 13 Wireless PGM Signal Strength
[326] PGM 6 Wireless PGM Signal Strength [334] PGM 14 Wireless PGM Signal Strength
[327] PGM 7 Wireless PGM Signal Strength [335] PGM 15 Wireless PGM Signal Strength
[328] PGM 8 Wireless PGM Signal Strength [336] PGM 16 Wireless PGM Signal Strength
Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)
Wireless Hardwire
PGM 1 Yes Yes
PGM 2 Yes Yes
PGM 3 to 16 Yes No

18 Programming Guide
Wireless Repeater Programming (MG-RPT1)
Wireless Repeater Assignment
For automatic assignment, press the wireless repeater’s anti-tamper switch while in the respective section.
Wireless Repeater Signal Strength
To view the wireless repeater’s signal strength, press the wireless repeater’s anti-tamper switch while in the respective
section.
Wireless Repeater Options
Section Wireless Repeater Serial Number
[545]= Repeater 1 ____/____/____/____/____/____/
[546]= Repeater 2 ____/____/____/____/____/____/
Section
[548] Wireless Repeater 1 Signal Strength
[549] Wireless Repeater 2 Signal Strength
Signal Strength Indicator 8 to 10 / 3 beeps = Best signal 5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)
Default:
Bold Section: MG-RPT1 #1 [551] MG-RPT1 #2 [561]
Option OFF ON OFF ON
[1] Wireless Repeater Supervision NN
[2] N/A N/A N/A N/A
[3] N/A N/A N/A N/A
[4] N/A N/A N/A N/A
[5] Repeat Wireless Keypad 1 Signals NN
[6] Repeat Wireless Keypad 2 Signals NN
[7] Repeat Wireless Keypad 3 Signals NN
[8] Repeat Wireless Keypad 4 Signals NN
Default:
Bold Section: MG-RPT1 #1 [552] MG-RPT1 #2 [562]
Option OFF ON OFF ON
[1] Repeat Wireless Zone 1 Signals NN
[2] Repeat Wireless Zone 2 Signals NN
[3] Repeat Wireless Zone 3 Signals NN
[4] Repeat Wireless Zone 4 Signals NN
[5] Repeat Wireless Zone 5 Signals NN
[6] Repeat Wireless Zone 6 Signals NN
[7] Repeat Wireless Zone 7 Signals NN
[8] Repeat Wireless Zone 8 Signals NN

Magellan 19
Default:
Bold Section: MG-RPT1 #1 [553] MG-RPT1 #2 [563]
Option OFF ON OFF ON
[1] Repeat Wireless Zone 9 Signals NN
[2] Repeat Wireless Zone 10 Signals NN
[3] Repeat Wireless Zone 11 Signals NN
[4] Repeat Wireless Zone 12 Signals NN
[5] Repeat Wireless Zone 13 Signals NN
[6] Repeat Wireless Zone 14 Signals NN
[7] Repeat Wireless Zone 15 Signals NN
[8] Repeat Wireless Zone 16 Signals NN
Default:
Bold Section: MG-RPT1 #1 [554] MG-RPT1 #2 [564]
Option OFF ON OFF ON
[1] Repeat Wireless Zone 17 Signals NN
[2] Repeat Wireless Zone 18 Signals NN
[3] Repeat Wireless Zone 19 Signals NN
[4] Repeat Wireless Zone 20 Signals NN
[5] Repeat Wireless Zone 21 Signals NN
[6] Repeat Wireless Zone 22 Signals NN
[7] Repeat Wireless Zone 23 Signals NN
[8] Repeat Wireless Zone 24 Signals NN
Default:
Bold Section: MG-RPT1 #1 [555] MG-RPT1 #2 [565]
Option OFF ON OFF ON
[1] Repeat Wireless Zone 25 Signals NN
[2] Repeat Wireless Zone 26 Signals NN
[3] Repeat Wireless Zone 27 Signals NN
[4] Repeat Wireless Zone 28 Signals NN
[5] Repeat Wireless Zone 29 Signals NN
[6] Repeat Wireless Zone 30 Signals NN
[7] Repeat Wireless Zone 31 Signals NN
[8] Repeat Wireless Zone 32 Signals NN

20 Programming Guide
Remote control signals are always repeated.
Default:
Bold Section: MG-RPT1 #1 [556] MG-RPT1 #2 [566]
Option OFF ON OFF ON
[1] Repeat Wireless 2-Way PGM 1 Signals NN
[2] Repeat Wireless 2-Way PGM 2 Signals NN
[3] Repeat Wireless 2-Way PGM 3 Signals NN
[4] Repeat Wireless 2-Way PGM 4 Signals NN
[5] Repeat Wireless 2-Way PGM 5 Signals NN
[6] Repeat Wireless 2-Way PGM 6 Signals NN
[7] Repeat Wireless 2-Way PGM 7 Signals NN
[8] Repeat Wireless 2-Way PGM 8 Signals NN
Default:
Bold Section: MG-RPT1 #1 [557] MG-RPT1 #2 [567]
Option OFF ON OFF ON
[1] Repeat Wireless 2-Way PGM 9 Signals NN
[2] Repeat Wireless 2-Way PGM 10 Signals NN
[3] Repeat Wireless 2-Way PGM 11 Signals NN
[4] Repeat Wireless 2-Way PGM 12 Signals NN
[5] Repeat Wireless 2-Way PGM 13 Signals NN
[6] Repeat Wireless 2-Way PGM 14 Signals NN
[7] Repeat Wireless 2-Way PGM 15 Signals NN
[8] Repeat Wireless 2-Way PGM 16 Signals NN