Linak HOMELINE CBD6DC User manual

Page 1 of 20
LINAK.COM/HOMELINE
CBD6DC HOMELINE®
User manual

Page 2 of 20
Contents
Preface............................................................................................................................................ 3
Valid for.......................................................................................................................................... 4
Important information ................................................................................................................. 5
Safety instructions........................................................................................................................ 5
Safety issues.............................................................................................................................. 6
Before installation, reinstallation or troubleshooting ................................................................... 6
Before start-up .......................................................................................................................... 6
During operation........................................................................................................................ 6
Misc .......................................................................................................................................... 6
Only for EU markets...................................................................................................................... 7
Only for Non EU markets ............................................................................................................. 7
Misuse ............................................................................................................................................ 7
Informations importantes............................................................................................................ 8
Consignes de sécurité................................................................................................................... 8
Avant l´installation, ré-installation ou le dépannage.................................................................... 9
Avant de démarage.................................................................................................................... 9
Pendant le fonctionnement ........................................................................................................ 9
Divers........................................................................................................................................ 9
Seulement pour les marchés au sein de l´UE............................................................................. 10
Seulement pour les marchés hors UE......................................................................................... 10
Utilisation abusive ........................................................................................................................ 10
Repairs............................................................................................................................................ 11
Misc. on the CBD6DC HOMELINE ................................................................................................ 12
Description of the CBD6DC HOMELINE ..................................................................................... 12
Installation..................................................................................................................................... 13
Mounting the CBD6DC on the TD4/TD5 Advanced...................................................................... 13
Mounting the CBD6DC on the bed frame ................................................................................... 14
Electrical connection .................................................................................................................... 14
External power supply................................................................................................................ 14
Label ............................................................................................................................................ 15
Disposal of LINAK products......................................................................................................... 16
Main groups of disposal............................................................................................................... 17
Disposal of batteries .................................................................................................................... 17
Drawing appendix......................................................................................................................... 18
Addresses....................................................................................................................................... 20

Page 3 of 20
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It
is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation.
Before our products leave the factory they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local dealer.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a limited warranty on its products. This warranty is, however, subject to correct use in
accordance with the specifications, maintenance being done correctly, and any repairs being carried out at
a service centre, which is authorised to repair LINAK products. You can review the full terms of the LINAK
warranty on the LINAK website www.linak.com/warranty.
Changes in installation and use of LINAK products/systems can affect their operation and durability. The
products are not to be opened by unauthorised personnel.
The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S

Page 4 of 20
Valid for:
This User Manual is valid for the following products:
(See the first 3 - 5 characters on the label)
Actuators: TD4 Advanced,TD5 Advanced, and LA40
Control box: CBD6DC
Controls: All wireless HOMELINE®controls
Power supply: SMPS001, SMPS002 and SMPS006
Accessories: WiFi2LIN module, BLE2LIN, Bed Control App, LED light rail, and massage motor

Page 5 of 20
Safety instruction
General
Important information
Important information on LINAK®products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – risk of injury if these instructions are not followed.
The system is not intended for use by young children or infirm persons
without supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the product is to be
fitted, there must be no possibility of personal injury, for example squeezing
of fingers or arms.
Ensure free space for movement of the application in both directions.
The CBD6DC is available as a 2-channel version and requires an external
power supply unit, for example the SMPS006.
The product is only to be used with the power supply unit provided with the
product.

Page 6 of 20
Safety issues
The builder of the equipment shall ensure that the use of the component
complies with relevant standards – like the Machine Directive. Care must be
taken to avoid squeezing of cables as it can cause movement of the system!
The CBD6DC and the SMPS001/002/006 must not be packed in heat
insulating material, but must be placed so that they can emit waste heat to
the surroundings. There are no ventilation holes to consider, the CBD6DC/
SMPS emits heat through its surface.
Only the power supply type SMPS001, SMPS002 or SMPS006, shall be used
with the system.
Before installation, de-installation or troubleshooting:
• Stop the control box CBD6DC HOMELINE®.
• Disconnect the power supply.
Before start-up:
• Make sure that the system has been installed as instructed in this User Manual.
• Make sure that the voltage is correct before the system is connected to the mains.
(See the CBD6DC HOMELINE®label in the appendix).
• System connection. The individual parts must be connected before connecting to
the mains.
During operation:
• If the control box makes unusual noise or smells, switch off the mains voltage
immediately.
• Take care that the cables are not damaged.
• Unplug the mains cable on mobile equipment before it is moved.
Misc:
Updated manuals and declarations can always be found here:
www.linak.com/homeline

Page 7 of 20
Only for EU markets
This product can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have given supervision or instruction concerning use of the
product in a safe way and understand the hazards involved.
Children shall not play with the product. Cleaning and user maintenance shall
not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/
products, unless they are under surveillance or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the
safety of these persons.
Moreover, children must be under surveillance to ensure that they do not
play with the product.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the system in environments other than the intended indoor use.

Page 8 of 20
Consignes de sécurité
Géneral
Informations importantes
Les informations importantes sur les produits LINAK®peuvent être trouvées dans
les rubriques suivantes:
Attention!
Le non respect de ces instructions peut entraîner des accidents impliquant
des blessures graves.
Ne pas suivre ces instructions peut entraîner l´endommagement ou
destruction du produit.
Le non respect de ces instructions peut entraîner des accidents impliquant des
blessures graves.
Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du produit.
L´utilisation en toute sécurité du système n´est possible que si l´intégralité des instructions
ont été lues et ont été strictement suivies.
Le non respect de se conformer aux instructions marquées du symbole “note”
peut entraîner de graves dommages au système ou à un de ses composants.
Il est important pour tout individu qui connecte, installe, ou utilise le système
d´avoir les informations nécessaires et l´accès à ce mannuel d´utilisation.
Suivez les instructions pour le montage – risque de blessure si ces instructions
ne sont pas suivies.
L´appareil n´est pas destiné à être utilisé par des enfants ou des personnes
handicapées sans surveillance.
S´il y a des dommages visibles sur le produit, l´installation ne doit pas être effectuée.
Prendre en compte lors de la construction du matériel, dans lequel l´actionneur
est incorporé, qu´il ne doit y avoir aucune possibilité de blessures corporelles,
telles que la compression des doigts ou des bras.
Assurez un espace libre autours du materiel pour éviter tout blocage.
Le CBD6DC existe en version 2 canaux et nécessite un module d’alimentation
externe, par exemple le SMPS006.
Le produit ne doit être utilisé qu’avec le module d’alimentation fourni avec lui.

Page 9 of 20
Avant l´installation, ré-installation ou le dépannage:
• Arrêtez control box CBD6DC HOMELINE®
• Retirez la prise du secteur
Avant de démarage:
• Assurez-vous que le système a été installé comme indiqué dans le mannuel
d´utilisateur.
• Assurez-vous que la tension du boîtier de contrôle est correcte avant que le système
soit connecté sur le secteur (Voir l’étiquette du CBD6DC HOMELINE®en annexe).
• Système de connection. Les différentes pièces doivent être connectées entre elles
avant que le boîtier de contrôle soit connecté au secteur. Consultez le manuel
d´utilisation si nécessaire.
Pendant le fonctionnement:
• Si le boîtier de contrôle émet un bruit ou odeurs inhabituelles, éteignez la tension
immédiatement.
• Veuillez à ce que les cables ne soient pas endommagés.
• Débranchez le cable d´alimentation sur l´équipement mobile avant qu´il ne soit
déplacé.
• Les produits ne doivent-être utilisés que dans un environement qui correspond à
leur IP.
Divers:
Les mises à jours des manuels et autres informations peuvent-être trouvées sur
www.linak.com/homeline
Instructions de sécurité
Le constructeur de l’équipement doit s’assurer que l’utilisation du composant
est conforme aux normes en vigueur, comme la directive sur les machines. Il
faut veiller à ne pas écraser les câbles, car cela peut entraîner un mouvement
du système!
Le CBD6DC et le SMPS001/002/006 ne doivent pas être emballés dans un
matériau isolant, mais doivent être placés de manière à pouvoir émettre de la
chaleur résiduelle dans l’environnement. Il n’y a pas de trous de ventilation à
prendre en compte, le CBD6DC/ SMPS émet de la chaleur par sa surface.
Seules les alimentations de type SMPS001, SMPS002 ou SMPS006 doivent
être utilisées avec le système.

Page 10 of 20
Seulement pour les marchés au sein de l´UE:
Ce produit peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi que les
personnes dont les capacités physiques, sensorielles ou mentales sont réduites
ou ayant un manque d´expérience et de connaissance si elles ont bénéficié
d´une surveillance ou d´instructions concernant l´utilisation du produit en
toute sécurité et compris les risques encourus.
Les enfants ne doivent pas jouer avec le produit. Le nettoyage et l´entretien ne
doivent pas être rèalisés par des enfants sans surveillance.
Seulement pour les marchés hors UE:
Les personnes qui n´ont pas l´expérience ou les connaissances nécessaires sur
le ou les produit(s) ne doivent pas le ou les utiliser. Par ailleurs, les personnes
ayant des capacités physiques, sensorielles ou mentales réduites ne doivent
pas utiliser le ou les produit(s), sauf si elles sont sous surveillance ou ont
suivi une formation approfondie de l´utilisation de l´appareil par l´individu
responsable de la securité de ces personnes.
De plus, les enfants doivent-être sous surveillance afin de s´assurer qu´ils ne
jouent pas avec le produit.
Utilisation abusive:
Ne surchargez pas les actionneurs – cela peut engendrer un risque de
blessures corporelles et endommager le système.
Ne pas utiliser le système dans dans des environnements autres que
l´utilisation intérieure prévue.

Page 11 of 20
Repairs
In order to avoid the risk of malfunction, all HOMELINE®repairs must only be carried out by authorised LINAK service centres
or repairers, as special tools must be used and special gaskets must be fitted. Products under warranty must also be returned
to authorised LINAK service centres.
Further information on LINAK warranty can be found on the LINAK website www.linak.com/warranty.
EU DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
Herewith declares under our sole responsibility that the LINAK dual actuator system TWINDRIVE®for use in
adjustable beds:
With main component (mark with CE) that are model: TDA and TDB
(with item number; TDa0b000Bccdd00, TDa1b000Bccdd00
(where; a describing spindel pitch; b describing Load rating; cc describing Back Angle; dd describing Leg Angle))
And options of
Port expander:CBD6DC
Linear Actuator(s): LA40
Controls: HC10B, HC20BL, HC30BL, HC40BL, HC05BL, BP10
Power Unit:SMPS001, SMPS006
Under bed light: LEDLightRail001, LEDLightRail002, LEDLR001-0001-xx
Accessories: Massage Motor; MD1000Dx
For Radio Components complies with 2014/53/EU Radio Equipment Directive (RED) according to the standards:
Safety:
EN 60335-1:2012 + AC:2014 + A11:2014 + A13:2017 + A1:2019 + A14:2019 + A2:2019
EN 62368-1:2014 + A1:2017
EMC:
ETSI EN 301 489-1 V2.2.3(2019 -11)
Draft ETSI EN 301 489-17 V3.2.2(2019 -12)
Radio:
EN 300 328 V2.2.2 (2019-07)
Health:
EN 62233:2008+AC:2008, EN 50663:2017, EN 62479:2010
For Power Unit complies with the EMC Directive: 2014/30/EU according to following standard:
EN 55032:2015, EN 61000-3-2:2014, EN 61000-3-3:2013, EN 55024:2010+A1:2015
and complies with Low Voltage Directive 2014/35/EU according to the standards:
EN 61558-1:2005 + A1:2009, EN 61558-2-16:2009 + A1:2013
And complies with regulation Ecodesign requirements for external power supplies (EU) 2019/1782 according to the
standard:
EN 50563:2011 + A1:2013
For Under bed light, Port expander and Linear Actuator components complies with 2014/30/EU EMC Directive
according to the standards:
EN 61000-6-2:2005/AC:2005, EN 61000-6-3:2007/A1:2011/AC:2012
And Port expander and Linear Actuator comply with Low Voltage Directive 2014/35/EU according to the standard:
EN 60335-1:2012+AC:2014+A11:2014+A13:2017+A1:2019 +A14:2019 +A2:2019, EN 62233:2008 + AC:2008
All components comply with RoHS2 Directive 2011/65/EU and RoHS3 Directive 2011/65/EU according to the
standard:
EN 50581:2012
Nordborg, 2021-10-28

Page 12 of 20
Misc. on the CBD6DC HOMELINE
The CBD6DC is an optimal choice for TD4/TD5 Advanced and LA40 applications together with various accessories, such as
massage motors or extra light.
Warranty
This HOMELINE product is subject to warranty pursuant to the terms of LINAK HOMELINE Warranty Paper, available on the
LINAK website www.linak.com/warranty.
Maintenance
Clean dust and dirt on the outside of the system at appropriate intervals and inspect it for damage and breaks.
Inspect the connections, cables and plugs and check for correct functioning as well as fixing points.
The cleaners and disinfectants must not be highly alkaline or acidic
(pH value 6-8).
Description of the CBD6DC HOMELINE
The control box ensures smooth adjustment of the bed and soft start and stop of the connected actuators.Another feature is
auto-detection of the type.
The CBD6DC is a small and compact control box that requires a minimum of space when mounted.
On opposite sides, the control box has two plugs for connection of actuators. Furthermore, it has two DC plugs and two RJ45
plugs. All plugs are white, so they are easily recognised, for example under the bed.
The CBD6DC is available as a 2-channel version and requires an external power supply unit, for example the SMPS006.
From an environmental perspective, the CBD6DC is a good choice as it has extremely low power consumption in standby mode,
only 0.1 W, and the CBD6DC control box is PVC-Free™, which is state-of-the-art.

Page 13 of 20
Installation
Do not pack the CBD6DC in heat insulating material.
Place the CBD6DC so it can emit heat through its surface to the surroundings.
Mounting the CBD6DC on the TD4/TD5 Advanced
1. The CBD6DC can be mounted directly on a TD4/TD5 by means of the bracket and one screw.
NOTE:
Bracket and screw must be ordered separately (item number SA1062W1004).
2. The bracket fits into the existing screw holes in the TD4/TD5. Place the bracket on the TD4/TD5 and fasten the screw.
3. Place the CBD6DC on the bracket. Push down until it is clicked onto the bracket.
4. Plug the cables in the CBD6DC and the TD4/5.

Page 14 of 20
Mounting the CBD6DC on the bed frame
1. Mount CBD6DC using two screws with a head diameter of 10 mm (8 to10 mm can be used).
2. Fasten mounting screws (max. torque 1 Nm).
Notes:
• The surface to which the control box is mounted should have an evenness better than ± 0.5 mm.
• The control box can also be mounted using one or two M6 nuts and screw counterparts, see Drawing appendix.
• The power plug must be accessible when the CBD6DC is mounted so that the supply to the CBD6DC can be
disconnected if replacement is required.
Electrical connection
External power supply
The CBD6DC is compatible with Switch Mode Power Supply SMPS001, SMPS002 and SMPS006.
1. Connect the actuator motor cable(s) to plug(s) 1 (and 2).
2. Connect any other accessories/devices.
3. Connect the external power supply (SMPS) to the CBD6DC.

Page 15 of 20
Label for CBD6DC HOMELINE

Page 16 of 20
Disposal of LINAK products
As LINAK customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that
enables a classification to different waste fractions for recycling or combustion.
Guidance
We recommend to disassemble our product into as many fractions as possible at the disposal and try to make it recycable. As
examples of main groups within waste fractions we can mention:
Metal, plastic, cable shoe, combustible waste and collection for recovery.
Some of these main groups can be subdivided, e.g. metal can be divided into iron, stainless steel and aluminium and alloy
steel. Plastic can e.g. be divided into ABS, PA, PE and PP.
As an example of sorting, please find below a list stating in which recycling groups the different components of LINAK
products ought to be placed:
By now almost all our cast plastic parts are supplied with an interior code for plastic type and fibre contents, if any.
Product Components Recycling group
Actuator: Spindle and motor Scrap
Plastic housing Plastic recycling or combustion
Cable Cable scrap or combustion
Massage motor: Plastic housing Plastic recycling or combustion
Cable Cable scrap or combustion
Control box: PCB Electronics scrap
Plastic housing Plastic recycling or combustion
Handset/Control: Plasic housing Plastic recycling or combustion
PCB Electronics scrap
Batteries Recovery

Page 17 of 20
Product main groups Scrap Cable
scrap
Electronics
scrap
Plastic recycling
or combustin
Comments
CBD6DC HOMELINE X X
Main groups of disposal
Disposal of batteries
Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that used
or leaking batteries are disposed through the local recycling system. Please do not throw used or leaking batteries in normal
household waste or in nature. This will cause damage to the enviroment.
How to deal with leaking batteries
Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product the batteries must be removed at once to minimise damage to the product. If
leaking batteries are left in the product, it may become defective.
It is recommended to use plastic gloves when handling leaking batteries. The contents of leaking batteries can cause chemical
burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please seek medical
attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek medical attention.

Page 18 of 20
DRAWING APPENDIX
CBD6DC dimension
Screw hole dimension

Page 19 of 20
LINAK APPLICATION POLICY
The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as
hardware, software, technical advice, etc. related to an existing or a new customer application.
LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk, and
Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be installed, used, and operated, as
each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application, vibration,
load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be the responsibility of the
LINAK customer using any LINAK product.
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the
responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.

Copyright ©LINAK 2021.11 MA-M9-02-911
FACTORIES
• Denmark
LINAK A/S
Group Headquarters
Tel: [phone]
Fax: [phone]
Fax (Sales): [phone]
www.linak.com
• Denmark
LINAK Profiles
Tel: [phone]
www.linak-profiles.com
• China
LINAK (Shenzhen) Actuator Systems, Ltd.
Tel: [phone]
Fax: [phone]
www.linak.cn
• Slovakia
LINAK Slovakia s.r.o.
Tel: [phone]
Fax: [phone]
www.linak.sk
• Thailand
LINAK APAC Ltd.
Tel: [phone]
www.linak.com
• USA
LINAK U.S. Inc.
Americas Headquarters
Tel: [phone]
Fax: [phone]
www.linak-us.com
SUBSIDIARIES
• Australia
LINAK Australia Pty. Ltd
Tel: [phone]
Fax: [phone]
www.linak.com.au
• Austria
LINAK Repräsentanz
Österreich (Wien)
Tel: [phone]
Fax: [phone]
www.linak.at - www.linak.hu
• Belgium
LINAK Benelux
(Belgium & Luxembourg)
Tel: [phone]
www.linak.be - www.fr.linak.be
• Brazil
LINAK Do Brasil Comércio De Atuadores Ltda.
Tel: [phone]
Fax: [phone]
www.linak.com.br
• Canada
LINAK Canada Inc.
Tel: [phone]
Fax: [phone]
www.linak-us.com
• China
LINAK (Shenzhen) Actuator Systems, Ltd.
Tel: [phone]
Fax: [phone]
www.linak.cn
• Czech Republic
LINAK C&S s.r.o.
Tel: [phone]
Fax: [phone]
www.linak.cz - www.linak.sk
• Denmark - Headquarters
LINAK A/S - Group Headquarters
Tel: [phone]
Fax: [phone]
Fax (Sales): [phone]
www.linak.com
• Denmark - International
LINAK International
Tel: [phone]
www.linak.com
• Denmark - Sales
LINAK DANMARK A/S
Tel: [phone]
Fax: [phone]
www.linak.dk
• Finland
LINAK OY
Tel: [phone]
www.linak.fi
• France
LINAK FRANCE E.U.R.L
Tel: [phone]
Fax: [phone]
www.linak.fr
• Germany
LINAK GmbH
Tel: [phone]
Fax: [phone]
www.linak.de
• India
LINAK A/S India Liaison Office
Tel: [phone]
Fax: [phone]
www.linak.in
• Ireland
LINAK UK Limited (Ireland)
Tel: [phone]
Fax: [phone]
[phone] (UK Mobile)
[phone] (Republic of Ireland
Mobile)
www.linak.co.uk
• Italy
LINAK ITALIA S.r.l.
Tel: [phone]
Fax: [phone]
www.linak.it
• Japan
LINAK K.K.
Tel: [phone]
Fax: [phone]
www.linak.jp
• Malaysia
LINAK Actuators Sdn. Bhd.
Tel: [phone]
Fax: [phone]
www.linak.my
• Netherlands
LINAK Benelux
Tel: [phone]
www.linak.nl
• New Zealand
LINAK New Zealand Ltd
Tel: [phone]
Fax: [phone]
www.linak.com.au
• Norway
LINAK Norge AS
Tel: [phone]
www.linak.no
DISTRIBUTORS
• Argentina
NOVOTEC ARGENTINA SRL
Tel: [phone]
Fax: [phone]
www.novotecargentina.com
• Colombia
MEM Ltda
Tel: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684
www.mem.net.co
• India
Mechatronics Control Equipments India Pvt Ltd
Tel: [phone], 85
www.mechatronicscontrol.com
• Indonesia
PT. HIMALAYA EVEREST JAYA
Tel: [phone] 544 8965
Fax: [phone]
Fax (Sales): [phone]
www.hej.co.id
• Iraq
Scan Medical Tech
Tel: [phone]
• Israel
NetivTech LTD
Tel: [phone]
Fax: [phone]
www.netivtech.com
• Kingdom of Bahrain
Mechatronics Industrial Equipments
Tel: [phone]
Fax: [phone]
www.mechatronicsbh.com
• Qatar
Mechatronics Industrial Equipments
Tel: [phone]
Fax: [phone]
www.mechatronicsqatar.com
• Russia
OOO FAM
Tel: [phone]
Fax: [phone]
www.fam-drive.ru
• Singapore
Servo Dynamics Pte Ltd
Tel: [phone]
Fax (Sales): [phone]
• South Africa
Industrial Specialised Applications CC
Tel: [phone]
www.isaza.co.za
• United Arab Emirates
Mechatronics Industrial Equipments LLC
Tel: [phone]
Fax: [phone]
www.mechatronics.ae
• Poland
LINAK Polska
LINAK Danmark A/S (Spólka Akcyjna)
Tel: [phone] 295 09 71
www.linak.pl
• Republic of Korea
LINAK Korea Ltd.
Tel: [phone]
Fax: [phone]
www.linak.kr
• Russia
LINAK LLC
Tel: [phone]
Fax: [phone]
www.linak.ru
• Slovakia
LINAK Slovakia s.r.o.
Tel: [phone]
www.linak.sk
• Spain
LINAK Actuadores, S.L.u
Tel: [phone]
Fax: [phone]
www.linak.es
• Sweden
LINAK Scandinavia AB
Tel: [phone]
Fax: [phone]
www.linak.se
• Switzerland
LINAK AG
Tel: [phone]
Fax: [phone]
www.linak.ch - www.fr.linak.ch
www.it.linak.ch
• Taiwan
LINAK (Shenzhen) Actuator systems Ltd.
Taiwan Representative office
Tel: [phone]
Fax: [phone]
www.linak.tw
• Thailand
LINAK APAC Ltd.
Tel: [phone]
• Turkey
LINAK İth. İhr. San. ve Tic. A.Ş.
Tel: + 90 312 4726338
Fax: + 90 312 4726635
www.linak.com.tr
• United Kingdom
LINAK UK Limited
Tel: [phone]
Fax: [phone]
www.linak.co.uk
• USA
LINAK U.S. Inc.
North and South American Headquarters
Tel: [phone]
Fax: [phone]
www.linak-us.com
www.linak-latinamerica.com
LINAK®accepts no responsibility for possible errors
or inaccuracies in catalogues, brochures, and other
material. LINAK reserves the right to change its
products without prior notice. LINAK cannot guar-
antee product availability and reserves the right to
discontinue the sale of any product.
The user is responsible for determining the suitabil-
ity of LINAK products for a specific application. All
sales are subject to the ‘Standard Terms of Sale and
Delivery’, available on LINAK websites.
LINAK and the LINAK logotype are registered trade-
marks of LINAK A/S.All rights reserved.