Linda Lewis LLKPM10 User manual

- 1 -
Instruction Manual
20 Litre Planetary Mixer
LLKPM20

- 2 -
Introduction
Thank you for purchasing a Linda Lewis Kitchens Ltd product. In this
booklet you will find instructions for safe operation so please read
carefully and retain for future reference. The planetary mixers have
a stirring hook that rotates. They have three speed settings and use
a combination transmission composed of a locking band, triangle
belt and chains.
Warnings and Precautions
The following warnings and precautions are important and must be
observed:
•Never immerse the mixer in water. If the mixer does become
completely wet, it must be dried and checked by a qualified
specialist before it is used again.
•The mixer cannot be used if the protective cover switch is not
functioning.
•Prior to installation, please read the instructions fully.
•Do not put your hand or other items into the bowl when the
machine is in operation.
•Whenever a speed change is made, the main switch must be
turned off beforehand and then the slow or fast button must
be pressed. This ensures a long service life of the mixer.
•Do not leave the mixer unattended when it is in operation.
•Please unplug the electrical cord when the mixer is not in use.
Disclaimer: The manufacturer will accept no liability for any injury
or damage caused by incorrect usage of the mixer.
Technical Data
Specifications:
LLKPM20
Motor Power
1.1kW
Width
500mm
Depth
600mm
Height
780mm
Weight
107kg
Specifications are subject to change. Please check the rating label
on the back of the machine.

- 3 -
Parts Identification
Please familiarise yourself with the various parts of the mixer before
use.
1. Gear Change Hand Lever
2. Stirring Shaft
3. Mixer
4. Stainless Bowl
5. Power Switch
6. Bowl Lift Lever
7. Safety Guard (with micro-switch)
8. Support

- 4 -
Operating Instructions
1. The machine must be placed on a dry, level surface to ensure
the mixer is stable.
2. Check the power voltage of the socket matches the mixer’s
required voltage and ensure it is properly earthed before
plugging in the mixer.
3. Slide the guard across and pour the ingredients into the bowl.
4. Close the guard and set the stirring speed.
5. Switch on the mixer using slow speed at first, then switch to
fast speed to ensure uniform dough is produced.
6. If the machine is stopped during the mixing process, be sure
to return to the lowest speed when starting the machine up
again.
Maintenance
Cleaning
Spilled food should be removed immediately from all exterior
surfaces. Also, it is important to clean the mixer after use. To
remove dirt or marks from the mixer, it is best to wipe with a soft
damp cloth. The stainless steel is washable. The mixer must not be
cleaned using a high-pressure jet.
Problems and Solutions
1. The mixer will not start – the power is not properly connected
or the guard is not fitted correctly
2. The guard switch is not operating correctly – open the guard
and check to see if the micro-switch is connected properly.
Check the power supply.
3. The mixer has overheated – this can occur if the mixer is
operated for too long, with excessive load. Overheating can
also come from electric leakage.
4. The mixer is operating with low efficiency – check to see if the
drive system is worn, whether the motor is in good condition,
whether the belt is loose or damaged. Remove the top cover
and the rear ventilating plate, adjust the belt, tighten the
wheel or the chains, thus the belt and the chains can be re-
tightened.

- 5 -
PM20 Parts Diagram

- 6 -
Parts for PM20
Ser.
No.
Part No.
Part Name
Ser.
No.
Part No.
Part Name
1
40506300
Wire Whip
42
50312002
Circlips for shaft 12
2
40506500
Spiral Dough Hook
43
40507200
Taper Gear Wheel
3
40506200
Flat Beater
44
40501700
Gear
4
40506700
Safety Guard
45
50405041
Bushing
5
50401006
Bowl Assembly
46
40501800
Sleeve
6
50405064
Plunger-Shifter Yoke
47
40502000
Claw Type Gear Wheel
7
50406021
Spring
48
40502100
Ring
8
50405029
Pin Shaft
49
50301007
Bearing 6205
9
40503600
Shifting Yoke
50
40502000
Bushing
10
40502900
Cam-Gear Shifter
51
50310010
Oil Seal 30x52x10
11
40503100
Plate-Shifter Index
52
50405074
Press board
12
50405016
Handle-Shifter
Cover
53
50601026
Support
13
40503300
Handle-Shifter
54
50601027
Case
14
40303300
Speed Handle
55
50304018
Nut
15
50405015
Plug
56
50301003
Bearing
16
40507100
Attachment Hub
57
40501100
Mid-gear wheel
17
50405065
Tighten Handle
58
50313013
Key 4*14
18
50405026
Ring
59
50312006
Circlips for shaft 18
19
40506600
Taper Gear Wheel
60
40501000
Gear
20
50403009
Top Cover
61
40500600
Bushing
21
50304020
Nut
62
40500500
Gear
22
50405032
Pressing Plate
63
40503800
Plug Cover
23
40501500
Plug Cover
64
50405025
Worm Pole
24
40503500
Super Machine Parts
65
50310002
Oil Seal
25
50308006
Declutch Shift Shaft
66
50506026
Green Button
26
50304006
Spring Washer 10
67
50506029
Red Button
27
40501400
Nut M10
68
50402024
Brand
28
40502300
Main Shaft
69
40500300
Motor Box
29
40502300
Gear Box
70
50313015
Key 5*14
30
40502400
Internal Gear
71
40500900
Shaft Worm Gear
31
40502700
Gear
72
40500800
Worm Wheel
32
50301006
Operating Shalf
73
50501016
Motor
33
50310008
Bearing
74
4050200
Back Housing
34
50310008
Oil Seal 28x47x10
75
40500100
Back Cover
35
40502800
Working shaft
76
40505600
Handle-Shifter
36
50306030
Retainer-pin 8x35
77
40505400
Crank Lever
37
50308008
Spring washer 14
78
40505200
Connecting Rod
38
50405051
Pressing plate
79
40504100
Stud
39
40500700
Transmission shaft
support
80
50307008
Clamp Plate
40
50301005
Bearing 6203
81
50307006
Clamp Plate
41
40501300
Spacer-lower
82
50406005
Spring