Lindab UltraLink FTCU User guide

lindab | we simplify construction
2020-07-01
Mounting instruction 3.5
LindabUltraLink®Controller
FTCU

Lindab reserves the right to make changes without prior notice
2020-07-01
UltraLink Controller FTCU
Please note:
• Do not remove the transducers!
• Do not use transducers as handles when you
mount the FTCU since this may cause damage!
Transducers
• Make sure the airflow arrow is pointing in the
direction of the airflow.
IP42
Status
Airflow
m³/h l/s m/s °C
Lindab UltraLink
Monitor FTMU
Airflow
direction arrow
• Rotate the senor body to the correct position
according t o next page.
• On FTCU’s sizes 400 — 630 loosen the nut so the
sensor body can be turned into the desired posi-
tion. The flange must then be fastened by tighten-
ing the nut.
Flange
• Position the display so it is visible from a suitable
direction.
• Mount the FTCU into the air duct system according
to the mounting instructions for Lindab Safe.
• When the FTCU is positioned accurately it should
be fixed with screws to the damper body in
the same way as when you connect ducts and
fittings.
• Never use a FTCU on the outlet side of a duct fan.
Place it on the inlet side or in worst case use a flow
conditioner if it must be placed on the outlet side.
• The longer distance to disturbance, i.e. the longer
straight duct before the UltraLink®, the higher the
measurement accuracy will be.
Duct fan

Lindab reserves the right to make changes without prior notice
2020-07-01
UltraLink Controller FTCU
Please note:
• The motor direction switch must always
be set to “1” as supplied.
Motor direct-
ion switch
Airflow
direction
arrow
• If the damper needs to be turned manually, then
press the manual override button on the motor
and turn the damper shaft with a 8 mm wrench or
similar.
Motor override
button
Damper shaft
• Note the ID-number of the FTCU. The ID is the
three last numbers of the serial number and can be
found:
- on the label of the box it was delivered in
- on the label on the FTCU itself
- in the display after pressing the “MODE” button
- in the App when the product is on
Controller FTCU Ø125
Serial no. 132600052
UltraLink
Lindab®
Disturbance * Placement of first flow sensor
Measurement uncertainty
± % or 1 l/s depending
wich is the greatest
A
2–4×Ød >4–5×Ød >5×Ød
Bend
a
Ød
*
Inner radius
(Best posi-
tion)
5 5 5
T-piece
a
Ød
*
Inner radius
(Best posi-
tion)
10 5 5
Reducer
a
Ød
*
Duct diameter
decrease 5 5 5
Reducer
a
Ød
*
Duct diameter
increase 10 5 5
Positioning

lindab |we simplify construction
Developed, designed and manufactured with the essential requirements by safe and security of the European Directive(s) and
Regulation(s):
2006/42/EC
1.1.2, 1.1.3, 1.3.4 Machinery Directive (MD)
Partly completed machinery must not be put into service until the
final machinery into which it is to be incorporated has been declared
in conformity with the provisions of the Machinery directive
2006/42/EC. We undertake to transmit, in response to a request by
the national authorities, relevant information on the product.
2004/108/EC Electromagnetic Compatibility Directive (EMC)
2011/65/EU & 2015/863/EC Restriction of Hazardous Substances (RoHS)
The partly completed machinery is developed, designed and manufactured with the essential requirements of the following
standards:
EN 61000-6-1:2002 - Part 6-1 Generic standards - Immunity for residential, commercial and light-industrial environments
EN 61000-6-2:2005 - Part 6-2 Generic standards - Immunity for industrial environments
EN 61000-6-3:2002 - Part 6-3
Generic standards - Emission standard for residential, commercial and light-industrial
environments
EN 61000-6-4:2002 - Part 6-4 Generic standards - Emission standard for industrial environments
FCC cuation and statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by the part responsible for compliance could void the user's
authority to operate the equipment. This equipment complies with FCC exposure limits set forth for an uncontrolled environment.
"This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help."
This declaration of conformity is established under the sole responsibility of the manufacturer identified in point 5.
Signed for and on behalf of the manufacturers by:
Authorised person:
Karel Kleinmond
Group Operations Director
2019-01-21 Karlovarska, Czech Repulic
Declaration of incorporation for partly completed
machinery and FCC statement
1. Declaration number 1002
2. Unique identification code of the product FTCU
3. Type
Ultrasonic device
4. Product description Measuring and controlling air flow and measuring temperature
5. Manufacturer Lindab Ventilation AB
Stålhögavägen 115, 26982 Båstad, Sweden
Telephone [phone], www.lindab.com