LINDR Kontakt 40-K-us Green Line User manual

KCH 01584 Kontakt 40-K-us Green Line
INSTRUCTION MANUAL FOR
LINDR CONTACT DRY
COOLER
ENGLISH
Number 004-2019 REV01 Valid 2020-02-06

2
LINDR.CZ s.r.o.
Sadová 132
503 15 Nechanice, Czech Republic
mob.: + 420 778 070 276
tel. : [phone]
e-mail: [email protected]
web: www.lindr.cz, www.lindr.eu
This manual contains instructions for installing, using and
operating the machine. This manual is an integral part of the
machine. It must be stored at the equipment for the life of the
equipment and provided to the user whenever it is installed,
moved, used, or maintained. Read this manual carefully before
installing and using the equipment, it contains important
information to ensure that all operations are performed in a
proper and safe manner.
This manual is a translation of the original Czech manual

ˇ
3
Contents:
1.
Introduction
…...............................................................
5
2.
Description of the cooler
…...............................................................
5
3.
Product label
…...............................................................
5
4.
General instructions, measures
and safety instructions
…...............................................................
6
5.
Installation and placement
…...............................................................
7
6.
Electrical connection
…...............................................................
8
7.
Testing
…...............................................................
8
8.
Warranty
…...............................................................
8
9.
Description of the cooler
…...............................................................
9
10.
Package contents
…...............................................................
10
11.
Tap installation
…...............................................................
11
12.
Keg coupler assembly
…...............................................................
12
13.
Beverage supply connection and
pressurisation
…...............................................................
15
14.
Inlet and outlet marking
…...............................................................
17
15.
Keg tapping and untapping
…...............................................................
18
16.
Putting into operation
…...............................................................
24
17.
Thermostat placement
…...............................................................
25
18.
Temperature and adjustment
…...............................................................
25
19.
Built-in air compressor
…...............................................................
26
20.
How to work with rapid couplings
…...............................................................
26
21.
Environmental protection
…...............................................................
27
22.
Maintenance
…...............................................................
27
23.
Inspection before every use
…...............................................................
27
24.
Periodic checks
…...............................................................
28
25.
Condenser cleaning
…...............................................................
28
26.
Sanitation by water
…...............................................................
29
27.
Table of defects
…...............................................................
31
28.
Spare parts
…...............................................................
32
29.
Technical data
…...............................................................
32
30.
Wiring diagram
…...............................................................
33
31.
Cooling diagram
…...............................................................
34

4
Symbols and Markings Used in the Manual
WARNING:
Not following instructions may cause injury or damage the
device.
WARNING:
Risk of injury by electrical current.
NOTE:
This symbol indicates information and recommendations for
users.
WARNING: The cooling system
contains flammable coolant R290
(propane)!

5
1. Introduction:
Thank you for purchasing this LINDR
product.
2. Description of the
Cooler
The dispensing system
with built-in compressor is designed for
professional cooling of beverages and
dispensing and serving well cooled
beer and beverages from a keg.
It is the elite among professional table-
top coolers.
The Lindr modern compressor cooling
unit uses input energy and transforms
it directly into cooling, ensuring proper
beer cooling at minimum energy drain.
The thermal block with high energy
capacity is ready to dispense well
cooled beer within 5 - 10 minutes after
turning on the device. If the thermostat
is set to max., the thermal block can
accumulate a large amount of energy it
can use to dispense well cooled beers
one after another. Time needed to
accumulate energy is ca. 10 min. Lindr
cooling technology has 45 % higher
output than is its input energy. The
cooler is fitted with an aftercooled tap
that ensures proper cooling even for
small amounts of beer. The full body
and the coil of the cooler are made of
stainless steel. The materials used
meet the strictest hygienic standards
and guarantee long service life of the
cooler.
3. Product Label

6
4. General Instructions,
Measures and Safety
Instructions
When using the device, follow basic
safety instructions stated by the
manufacturer. The cooling device is
designed for flow cooling of beverages
dispensed from kegs. Any other use is
considered impermissible and
therefore dangerous. The supplier is
not liable for damage caused by
incorrect use.
DO NOT USE THE DEVICE FOR
PURPOSES OTHER THAN THOSE
STATED BY THE MANUFACTURER!
General safety principles. Observe
the following safety instructions.
The supplier is not liable for damage
caused by activities carried out on this
device without observing the following
instructions!
WARNING: Children aged 15 or
more and persons with reduced
physical, sensory or mental capabilities
or insufficient experience and
knowledge may only use the device
when supervised or instructed in safe
use of the appliance and familiarised
with potential dangers.
WARNING: Children must not be
allowed to play with the appliance.
Store all packaging material out of
reach of children (comes with a plastic
bag –suffocation hazard).
WARNING: Cleaning and
maintenance of the appliance on
the part of the user must not be done
by unsupervised children.
WARNING: Before connecting to
main electrical supply, check that the
voltage and frequency in the mains
corresponds to the data stated on the
device.
WARNING: Always make sure the
power socket you plug the
appliance into has sufficient circuit
protection. See specifications on the
product label.
WARNING: Before any
interference with the device, such
as cleaning or maintenance, ALWAYS
disconnect the device from power
supply: set the thermostat thermostat
to "O" position and unplug the
appliance from the socket.
WARNING: Never place tools or
other object into the fan.
WARNING: Never touch electrical
components with wet or damp hands.
WARNING: To ensure the
cooling unit works properly and at full
capacity, make sure air supply to the
unit is not obstructed.
WARNING: Water temperature
during sanitation must not be higher
than 25 °C!
WARNING: Always make sure
the power socket you plug the device
into meets the specifications listed on
the product label (voltage, frequency,
input power).

ˇ
7
WARNING: When unplugging
the device from the socket, grab
the plug and pull it out. Do not under
any circumstances pull at the cable;
risk of damage.
WARNING: To turn the device off
completely, unplug the appliance from
the power socket.
WARNING: In the event the
electrical wiring of the product
becomes damaged, summon a trained
service technician. Do not under any
circumstances repair the device
yourself.
WARNING: The cooling system
contains flammable coolant R290
(propane)!
WARNING: Emergency
maintenance and repair of the cooling
system must be done by trained,
authorised technicians familiar with
cooling and electrical systems. The
technicians should have special
training and qualification for handling
flammable substances in order to
perform service on coolers
containing R290. Follow basic
regulations and safety measures
regarding service and repair!
WARNING: Do not use open
flame or potential sources of sparks in
the vicinity of a cooler using R290
coolant!
WARNING: After unpacking,
place the cooler so that heat created
by the cooling unit can be vented
sufficiently.
WARNING: Do not place objects
that could prevent air circulation on top
of the cooler.
5. Installation and Placement
Place the cooler on a horizontally level,
stable surface (maximum permitted
inclination of 2°). The device requires
sufficient free space around it to allow
air circulation.
- Ensure sufficient space for air
circulation and heat dissipation.
- Ensure sufficient access to
fresh air.
- The device must not be placed
in an enclosed space.
- The device must not be placed
in proximity to heat sources or
exposed to direct sunlight.
Minimum distance of vents from an
obstacle that would prevent air
circulation is 20 cm. In places where
there are no vents, minimum distance
is 7 cm. The device is best used in a
cool, well ventilated room. The device
is designed for use at ambient
temperature of 16°C – 32°C.The
device MUST NOT be used or stored
at ambient temperature lower than 0
°C. The device is designed for use in a
normal environment, always indoors,
protected from rain or sunlight.
Climate class N.

8
WARNING: The cooler must be
placed indoors (in a roofed area) on a
dry, level, stable surface.
WARNING: Protect the cooler
and electrical connection from
rain and spraying water!
WARNING: Do not under any
circumstances lay the cooler on its
side, not even during transport.
WARNING: The cooler must not
be placed in the vicinity of heat sources
or exposed to direct sunlight.
NOTE: In order for the device to
work correctly and at maximum
output, it is important to not cover up
any of the device's vents and ensure
sufficient air circulation.
6. Electrical Connection
Connect the device to a power socket
in accordance with specifications on
the product label of the device.
Electrical wiring is subject to local
regulations. If the power leads (cables)
are damaged, they must be replaced
by the manufacturer, their service
technician or a similarly qualified
person to prevent risk of hazardous
situations.
WARNING: Do not use or turn on
the device if the power lead (cable)
is damaged!
7. Testing
The product is delivered ready for
immediate use.
8. Warranty
The device comes with a warranty in
accordance with general legal
regulations of the Czech Republic or in
accordance with the trade agreement.
During the validity period of the
warranty, we will remove any defects
on the product free of charge, provided
these defects were not caused by
excess wear, improper handling,
incorrect storage or by using the
product in a way that is counter to the
instruction manual or the product's
design as defined by the manufacturer.
Materials replaced during the validity
period of the warranty are our property.
The legitimacy of the warranty claim is
always decided by an authorised
service centre. Warranty provided by a
retailer outside of the territory of the
Czech Republic is governed by the
agreement between the retailer and the
buyer in their mutual relationship; this
agreement is not directly linked to the
manufacturer. The agreement does not
give the buyer the right to submit
warranty claims to the manufacturer.
Transport expenses or other costs are
not covered by the warranty.
Attention:
Electrical devices and appliances must
be checked/inspected at a time
stipulated by valid legislation of the
country the device is operated in.
Inspection of wiring may only be done
by a person with valid authorisation for
this activity. Service work, provision of
spare parts and inspection is done by
the manufacturer or an authorised
service centre.

ˇ
9
9. Description of the Cooler
Kontakt 40-K-us Green Line
1
Cooler handle
7
Air compressor switch
2
Tap
8
Air outlet (5/16" speed fitting)
3
Thermostat
9
Beverage outlet (3/8" speed fitting)
4
Drip tray
10
Product label
5
Condenser vent grid
6
Fan

10
10. Package Contents
The package contains:
1. Tap
2. Tap wrench
3. Drip tray and sieve

ˇ
11
11.Tap Installation
Fit the tap perpendicularly
onto the spline coupler.
Secure with a flare nut
and turn to the left.
(loosen to the right).
Tighten with the enclosed wrench.

12
12.Keg Coupler Assembly
12.1 Outlet for keg pressurisation:
Connection variant with
bushing: hose is
fitted onto the bushing and
affixed with a clip.
Connection variant with rapid coupling:
Screw an F 5/8“ x 5/16“ (8 mm) rapid coupling onto the keg coupler

ˇ
13
WARNING:
Before you screw the rapid coupling onto the 5/8“ thread,
make sure the keg coupler (air inlet for delivery medium) has
a non-return valve fitted on it.

14
12.2 Outlet for beverage:
Screw an F 5/8“ x 3/8“ (9.5 mm) speed fitting onto the keg coupler

ˇ
15
13.Beverage Supply Connection and Pressurisation
Connect the cooling device to the keg coupler
by plugging a 3/8“ beverage hose into the
speed fitting located on the rear of the cooler
marked inlet 1, inlet 2.
Connect the cooling device to the keg coupler
by plugging a 5/16“ air hose into the rapid
coupling located on the rear of the cooler
marked air. To connect two kegs, use a 5/16“
Y speed fitting.
Plug the 3/8“ beverage hose leading from
the cooling device into the 5/8“- 3/8“ (9. 5
mm) speed fitting (beverage outlet on the
keg coupler).
Plug the 5/16“ air hose leading from the
cooling device into the 5/8“ - 5/16“ (8 mm)
speed fitting (air inlet on the keg coupler).

16

ˇ
17
14.Inlet and Outlet Marking
Tap –outlet 1
Tap –outlet 2

18
15.Keg Tapping and Untapping
WARNING:
Make sure the adapter is clean before tapping the keg!
S system keg coupler:
Procedure for tapping and untapping a keg with an S system keg coupler:
1. Keg tapping:

ˇ
19

20
2. Keg untapping: