Lindy 3.5” IDE User manual

USB 2.0 HDD Enclosure
3.5” IDE / SATA
Installation Guide English
Installationsanleitung Deutsch
Manuel Utilisateur Français
Manuale d’uso Italiano
Lindy No. 42793
www.lindy.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - First Edition (OCT 2009)
INSTALLATION
English
Slide the drive tray out of the housing. If present, set the
jumper on your IDE/ATA hard drive to the MASTER setting.
Attach the drive to the IDE (or SATA) and the power
cables. Slide the drive into the tray and secure using the
supplied screws. Slide the tray back into the housing and
reinstall the two screws
.
Deutsch
Lösen Sie die beiden Schrauben am Gehäusedeckel mit
den integrierten Anschlüssen und ziehen Sie den Einschub
heraus. Jumpern Sie Ihre IDE/ATA Festplatte als MASTER
sofern die Platte diese Möglichkeit anbietet. Stecken Sie
das IDE- bzw. SATA-Datenkabel sowie das jeweilige
Stromkabel auf und befestigen Sie die Festplatte mit
Schrauben vorsichtig am Einschub. Schieben Sie den
Einschub wieder ins Gehäuse und schrauben Sie ihn fest.
Français
Retirez les deux vis de la partie arrière et faites glisser le
capot. Si présent, réglez le cavalier du disque dur en mode
MASTER. Connectez le disque au connecteur IDE (ou
SATA) et son alimentation. Insérez doucement le disque
dur dans le boîtier et ne forcez pas sur les petites vis.
Refermez ensuite le capot et revissez-le à l’arrière.
Italiano
Rimuovete la copertura in plastica dall’astuccio. Se
presente, impostate il Jumper dell’hard disk in modalità
MASTER. Collegate il drive al connettore a 44 poli ou al
connettore SATA. Fate scivolare con cautela il disco
all’interno dell’astuccio e serrate le due viti. Fate attenzione
a non stringere eccessivamente!
OPERATION (English)
Power Requirements
This enclosure must always be used with the supplied
power supply. It can be connected to any USB port.
Driver Installation
Modern operating systems such as Windows 7, Vista, XP,
2000 and ME already include the necessary USB drivers
(as long as the drivers for your USB 2.0 ports are up to
date!) If the external hard drive is recognized correctly as a
USB 2.0 device then there is no need to install any other
drivers. Otherwise, obtain updated drivers for your USB
controller from your computer manufacturer’s web site.
Hard Drive Partitioning
If you use a brand new hard drive it may not have been
partitioned and your operating system will not show the
drive. Use the partitioning program from your operating
system (FDISK or similar). Find information on this topic
from the HELP section of your operating system, or get
help from an experienced technician.
ANSCHLUSS & BETRIEB (Deutsch)
Stromversorgung
Verwenden Sie dieses USB Festplattengehäuse nur
und immer mit dem mitgelieferten Netzteil!
For Home and Office Use
Tested to Comply with FCC Standards

Treiberinstallation
Moderne Betriebssysteme wie Windows 7, Vista, XP, ME,
2000 (mit aktuellen USB-Treibern) haben bereits alle
notwendigen USB-Treiber „on Board“. Sollte das externe
Laufwerk hier bereits als USB 2.0 Device erkannt werden
und funktionieren, so sollte keine weitere Treiberinstallation
vorgenommen werden! Andernfalls ist ein Update der
Treiber für ihren USB Controller (z.B. via Internet)
notwendig.
Partitionierung der Festplatte
Wenn Sie eine brandneue Festplatte anschließen ist diese
höchstwahrscheinlich nicht partitioniert und Ihr Betriebs-
system wird kein Laufwerk anzeigen! Verwenden Sie das
Partitionierungsprogramm Ihres Betriebssystems wie zum
Beispiel FDISK. Weitergehende Informationen hierzu
finden Sie im Hilfesystem Ihres Betriebssystems oder
wenden Sie sich an einen erfahrenen PC-Techniker.
UTILISATION (Francais)
Puissance Necessaire
Ce boîtier DOIT uniquement être utilisé avec l’alimentation
fournie. Il peut être connecté à n’importe quel port USB.
Installation du pilote
Les systèmes d’exploitation actuels comme Windows 7,
Vista, XP, 2000, ME incluent directement le pilote USB 2.0
et il sera mis à jour automatiquement. Si le disque dur
externe est reconnu correctement en tant que périphérique
USB 2.0 n’essayez pas de réinstaller le pilote.
Veuillez vous référer au manuel fourni pour l’installation
des pilotes sous d’autres systèmes.
Installation du disque dur
Si vous installez un nouveau disque dur et qu’il n’est pas
reconnu par le système, il est nécessaire de le partitionner
avant son utilisation (FDISK ou autre).
UTILIZZO (Italiano)
Alimentazione richiesta
Questo astuccio DEVE essere alimentato solo con
l’alimentatore fornito a corredo e può essere
connesso a qualsiasi porta USB.
Installazione dei Driver
I sistemi operativi moderni come Windows 7, Vista, XP,
2000 e ME includono già tutto il software USB necessario
(se le porte USB 2,0 sono già correttamente installate). Se
il drive viene correttamente riconosciuto come periferica
USB 2.0 non procedete all’installazione di alcun driver! In
caso contrario richiedete i driver aggiornati per il controller
USB a chi vi ha fornito il computer o scaricateli dal
corrispondente sito web.
Partizionamento dell’HDD
Se state utilizzando un Hard Disk esso potrebbe non
essere partizionato. Utilizzate il programma di
partizionamento del vostro sistema operativo (FDISK o
similare). Potrete trovare informazioni su questa
operazione nella guida del vostro sistema operativo o
chiedete aiuto ad un tecnico esperto.
Technical Data
For use with 3.5” hard drives
Interface: USB 2.0 to IDE & SATA
Enclosure dimensions approx.: 20.5 x 12 x 3cm
Enclosure weight: 0.3kg approx.
For indoor use only
Packing List
3.5” Hard Drive Enclosure w/ stand
USB A/B connection cable
SATA Data Cable / SATA Power Cable
IDE Flat Cable / IDE Power Cable
Bag with small HDD installation screws
External Power supply with separate power cable
Driver disk
This manual
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Lindy No. 42793
©LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH – First Edition, OCT 2009
For Home and Office Use
Tested to Comply with FCC Standards