Lindy 42906 User manual

USB 2.0 Hard Drive Enclosure
Installation Guide English
Installationsanleitung Deutsch
Manuel Utilisateur Français
Manuale d’uso Italiano
For 3.5” IDE HDD’s up to ATA/133
LINDY No. 42906
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (NOV 2005)
INSTALLATION
ENGLISH
Slide the HDD tray out of
the housing. If present,
set the jumper on your
IDE/ATA hard drive to
the MASTER setting.
Attach the drive to the IDE and power cables. Slide
the drive into the HDD tray and secure using the four
supplied screws. Slide the tray back into the housing
and reinstall the two screws.
DEUTSCH
Lösen Sie ggf. die beiden Schrauben am
Gehäusedeckel mit den integrierten Anschlüssen
und ziehen Sie den Einschub heraus. Jumpern
Sie Ihre IDE/ATA Festplatte als MASTER sofern
die Platte diese Möglichkeit anbietet. Stecken Sie
die beiden Kabel auf und befestigen Sie die
Festplatte mit 4 Schrauben vorsichtig am
Einschub. Schieben Sie den Einschub wieder ins
Gehäuse und schrauben Sie ihn wieder fest.
Français
Retirez les deux vis de la partie arrière et faites
glisser le capot. Si présent, réglez le cavalier du
disque dur en mode MASTER. Connectez le disque
au connecteur IDE et son alimentation. Insérez
doucement le disque dur dans le boîtier et ne forcez
pas sur les petites vis. Refermez ensuite le capot et
revissez-le à l’arrière.
Italiano
Rimuovete la copertura in plastica dall’astuccio.
Se presente, impostate il Jumper dell’hard disk in
modalità MASTER. Collegate il drive al connettore
a 44 poli come indicato in figura. Fate scivolare
con cautela il disco all’interno dell’astuccio e
serrate le due viti. Fate attenzione a non stringere
eccessivamente!
OPERATION (ENGLISH)
Power Requirement
This enclosure must always be used with the
supplied power supply.
It can be connected to any USB port.
Driver Installation
Modern operating systems such as Windows XP,
2000 and ME already include the necessary drivers
(as long as the drivers for your USB 2.0 ports are up
to date!). If the external hard drive is recognized
correctly as a USB 2.0 device then there is no need
to install any other drivers. Otherwise, obtain updated
drivers for your USB controller from your computer
manufacturer’s web site.
HDD Partitioning
If you use a brand new hard drive it may not have
been partitioned and your operating system will not
show the drive. Use the partitioning program from
your operating system (FDISK or similar). Find
information on this topic from the HELP section of
your operating system, or get help from an
experienced technician.
ANSCHLUSS & BETRIEB (DEUTSCH)
STROMVERSORGUNG
Verwenden Sie dies USB Festplattengehäuse nur
und immer mit dem mitgelieferten Netzteil!
Sie können dies Gehäuse an jeden, auch an einen
non-self-powered USB Port anschließen!
TREIBERINSTALLATION
Moderne Betriebssysteme wie Windows XP, ME,
2000 (mit aktuellen USB- Treibern) haben bereits alle
notwendigen Treiber an Board. Sollte das externe
Laufwerk hier bereits als USB 2.0 Device erkannt
werden und funktionieren, so sollte keine erneute
weitere Treiberinstallation vorgenommen werden!
Andernfalls ist ein Update der Treiber für ihren USB
Controller (z.B. via Internet) notwendig.
For Home and Office Use
Tested to Comply with FCC Standards

Fortsetzung: BETRIEB (DEUTSCH)
Partitionierung der Festplatte
Wenn Sie eine brandneue Festplatte anschließen ist
diese höchstwahrscheinlich nicht partitioniert und Ihr
Betriebssystem wird kein Laufwerk anzeigen!
Verwenden Sie das
Partitionierungsprogramm Ihres
Betriebssystems wie zum Beispiel FDISK. Weitergehende
Informationen hierzu finden Sie im Hilfesystem Ihres
Betriebssystem oder wenden Sie sich an einen erfahrenen
PC-Techniker.
UTILISATION (FRANCAIS)
PUISSANCE NECESSAIRE
Ce boîtier DOIT uniquement être utilisé avec
l’alimentation fournie.
Il peut être connecté à n’importe quel port USB.
Installation du pilote
Les systèmes d’exploitation actuels comme Windows XP,
2000, ME incluent directement le pilote USB 2.0 et il sera
mis à jour automatiquement. Si le disque dur externe est
reconnu correctement en tant que périphérique USB 2.0
n’essayez pas de réinstaller le pilote.
Veuillez vous référer au manuel fourni pour l’installation
des pilotes sous d’autres systèmes.
Installation du disque dur
Si vous installez un nouveau disque dur et qu’il n’est pas
reconnu par le système, il est nécessaire de le partitionner
avant son utilisation (FDISK ou autre).
UTILIZZO (ITALIANO)
Alimentazione richiesta.
Questo astuccio DEVE essere alimentato solo
con l’alimentatore fornito a corredo e può essere
connesso a qualsiasi porta USB.
Installazione dei Driver
I sistemi operativi moderni come Windows XP, 2000 e ME
includono già tutto il software necessario (se le porte USB
2,0 sono già correttamente installate). Se il drive viene
correttamente riconosciuto come periferica USB 2.0 non
procedete all’installazione di alcun driver! In caso contrario
richiedete i driver aggiornati per il controller USB a chi vi ha
fornito il computer o scaricateli dal corrispondente sito web.
Partizionamento dell’HDD
Se state utilizzando un Hard Disk esso potrebbe non
essere partizionato. Utilizzate il programma di
partizionamento del vostro sistema operativo (FDISK o
similare). Potrete trovare informazioni su questa
operazione nella guida del vostro sistema operativo o
chiedete aiuto ad un tecnico esperto.
Technical Data
For 3.5” hard drives!
Interface: USB 2.0 to IDE ATA/133
Enclosure dimensions approx.: 210 x 120 x 30mm
Enclosure weight: 0.4kg approx.
Operating temperature: -5…40°C,
Humidity: 10…80%, non condensing
(Operating temperature and humidity are dependent
on the installed hard drive. Please refer to your drives
data sheet!)
For indoor use only
Packing List
USB 2.0 Hard Drive Enclosure
USB A/B connection cable, 1m approx.
Bag with small HDD installation screws, screwdriver
Driver disk for Windows 98
External Power supply with separate power cable
This manual
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
For Home and Office Use
Tested to Comply
with FCC Standards
LINDY No. 42906
©LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - First Edition, NOV 2005