Lindy 52043 User manual

© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (Apr 2010)
For Home and Office Use
Tested to Comply with
FCC Standards
3G/ADSL2+ 802.11g VPN Router
Quick Installation Guide English
LINDY No. 52043
www.LINDY.com

English Quick Installation Guide
2
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY.
THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND
AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON CD-ROM.
Package Contents
•3G/ (802.11g) (VPN) ADSL2+ Firewall Router
•CD containing the on-line manual
•RJ-11 ADSL/telephone cable
•Ethernet (CAT-5 LAN) cable
•One 2dbi detachable antenna (Wireless model only)
•Power adapter
•RJ-45 to RS-232 Console Kit
•Quick Start Guide
•Splitter/ Micro-filter (Optional)
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a ualified
service center.
Avoid using this product and all accessories outdoors.

English Quick Installation Guide
3
Attention
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.

English Quick Installation Guide
4
Hardware Overview
The Front LEDs
Lit orange red when
power is ON. Lit red
means system is fail.
Lit green when the
system is ready.
Lit green when the wireless
connection is established.
Flashes when the device
sending /receiving data.
Lit green when
successfully connected
to an ADSL DSLAM
(“Line sync”)
Lit when connected to an
Ethernet device. Green for
100Mbps; Orange for 10Mbps.
Blinking when data is
Transmitted / Received.
´
The Rear Ports
Lit when the USB
device is ready.
Flashes when
sending /
receiving data.
Lit green
when there
are emails in
the inbox.
Lit green when IP connected.
Flashes green when IP connected
and IP traffic is passing thru the
device. Lit red when device
attempted to become IP connected
and failed. Lit off in bridged mode or
when connection WAN is absent.
Connect the
antenna.
Connect the supplied RJ-11
(“telephone”) cable on this
port when connecting to the
ADSL/ telephone network.
Connect your computer
to a LAN port, using a
UTP Ethernet cable.
Connect the USB
cable on this port.
Press it to reset the
device or restore to
factory default settings.
Push WPS button to
trigger Wi-Fi Protected
Setup function*.
Connect the supplied
power adapter to this
jack.
Power ON/
OFF switch
* Note: For WPS configuration, please refer to the WPS section of User Manual.

English Quick Installation Guide
5
3G/(802.11g) (VPN) ADSL2+ Firewall Router
Hardware Connection
Hardware Installation
1. Power Connection
Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different country.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other
side to the PC’s Ethernet interface.

English Quick Installation Guide
6
3. USB Connection
The USB 2.0 port supports 3G/ HSDPA modem connectivity: users can c
onveniently
access Internet via 3G, eliminating the limitations of the wired network. This solution
also employs an auto fail-over feature to ensure always-on connectivity for SOHO users.
4. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other
side to the phone jack on the wall.
5. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.

English Quick Installation Guide
7
6. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct high
frequency signals to the ADSL modem & low frequency signals to the telephone or
other analogue device to prevent inter-modulation distortion & get good speed/stable
ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then
a splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
Setup Utility
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.

English Quick Installation Guide
8
´
Connecting to the Router
1. Open the web browser and type http://192.168.1.254 in the browser's address box.
This number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”,
and password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may
have a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a
PC connected. If it is off, check the cables between your router and the PC. Make sure
you have uninstalled any software firewall for troubleshooting. Verify that the IP address
and the subnet mask are consistent between the router and the workstations.
3. Frequent loss of ADSL linesync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between
them and the wall socket (unless you are using a Central Splitter or Central Filter
installed by a qualified and licensed electrician), and ensure that all line filters are
correctly installed and the right way around. Missing line filters or line filters installed the
wrong way around can cause problems with your ADSL connection, including causing
frequent disconnections. If you have a back-to-base alarm system you should contact
your security provider for a technician to make any necessary changes.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User
Manual
.
If you cannot resolve the problem with the Troubleshooting chapter, please
contact the dealer where you purchased this product.

Radio Frequency Energy, Certifications
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if no
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interfere
nce to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the s
eparation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced technician for help
You are cautioned that changes or modifications
compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful i
2.
This device must accept any interference received, including interference that may cause undesired
operation
CE Statement, EMC Compatibilty
This device complies with EN Standards EN55022 and EN55024 according to the relevant EC EMC Direc
must be used with shielded cables only to maintain EMC compatibility.
Dieses Produkt entspricht den einschlägigen EMV Richtlinien der EU und darf nur zusammen mit
abgeschirmten Kabeln verwendet werden.
LINDY Herstellergarantie
LINDY gewährt für dieses Produkt über die gesetzliche Regelung hinaus eine zweijährige Herstellergarantie ab
Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den
AGBs.
WEEE (Waste of Electrical a
Recycling of Electronic Products
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste
electrical and electronic equipment. The wheelie bin symbol shown indicates that this produ
disposed of with household waste. Instead the product must be recycled in a manner that is environmentally
friendly. For more information on how to dispose of this product, please contact your local recycling centre or
your household waste d
isposal service. Each individual EU member state has implemented the WEEE
regulations into national law in slightly different ways. Please follow your national law when you want to dispose
of any electrical or electronic products.
More details can be obta
ined from your national WEEE recycling agency.
Germany / Deutschland
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das
Recycling von Elektro-
und Elektronikprodukten geschaffen. Diese wurden von der
und Elektronikgerätegesetz –
ElektroG in deutsches Recht umgesetzt. Dieses Gesetz verbietet vom 24.März
2006 an das Entsorgen von Elektro
-
lokalen Sammelsyst
emen bzw. örtlichen Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen
genommen. Die Kosten für den weiteren Recyclingprozess übernimmt die Gesamtheit der Gerätehersteller.
Radio Frequency Energy, Certifications
This equipment has been tested and found to comply with the limits for a Class B
Digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if no
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
nce to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
eparation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced technician for help
You are cautioned that changes or modifications
not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful i
nterference, and
This device must accept any interference received, including interference that may cause undesired
CE Statement, EMC Compatibilty
This device complies with EN Standards EN55022 and EN55024 according to the relevant EC EMC Direc
must be used with shielded cables only to maintain EMC compatibility.
Dieses Produkt entspricht den einschlägigen EMV Richtlinien der EU und darf nur zusammen mit
abgeschirmten Kabeln verwendet werden.
LINDY Herstellergarantie
LINDY gewährt für dieses Produkt über die gesetzliche Regelung hinaus eine zweijährige Herstellergarantie ab
Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den
WEEE (Waste of Electrical a
nd Electronic Equipment),
Recycling of Electronic Products
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste
electrical and electronic equipment. The wheelie bin symbol shown indicates that this produ
disposed of with household waste. Instead the product must be recycled in a manner that is environmentally
friendly. For more information on how to dispose of this product, please contact your local recycling centre or
isposal service. Each individual EU member state has implemented the WEEE
regulations into national law in slightly different ways. Please follow your national law when you want to dispose
of any electrical or electronic products.
ined from your national WEEE recycling agency.
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das
und Elektronikprodukten geschaffen. Diese wurden von der
Bundesregierung im Elektro
ElektroG in deutsches Recht umgesetzt. Dieses Gesetz verbietet vom 24.März
-
und Elektronikgeräten über die Hausmülltonne! Diese Geräte müssen den
emen bzw. örtlichen Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen
genommen. Die Kosten für den weiteren Recyclingprozess übernimmt die Gesamtheit der Gerätehersteller.
Digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if no
t
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
nce to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
not expressly approved by the party responsible for
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device must accept any interference received, including interference that may cause undesired
This device complies with EN Standards EN55022 and EN55024 according to the relevant EC EMC Direc
tive. It
Dieses Produkt entspricht den einschlägigen EMV Richtlinien der EU und darf nur zusammen mit
LINDY gewährt für dieses Produkt über die gesetzliche Regelung hinaus eine zweijährige Herstellergarantie ab
Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste
electrical and electronic equipment. The wheelie bin symbol shown indicates that this produ
ct must not be
disposed of with household waste. Instead the product must be recycled in a manner that is environmentally
friendly. For more information on how to dispose of this product, please contact your local recycling centre or
isposal service. Each individual EU member state has implemented the WEEE
regulations into national law in slightly different ways. Please follow your national law when you want to dispose
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das
Bundesregierung im Elektro
-
ElektroG in deutsches Recht umgesetzt. Dieses Gesetz verbietet vom 24.März
und Elektronikgeräten über die Hausmülltonne! Diese Geräte müssen den
emen bzw. örtlichen Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen
genommen. Die Kosten für den weiteren Recyclingprozess übernimmt die Gesamtheit der Gerätehersteller.
LINDY No. 52043
1
st
Edition, April 2010
www.lindy.com