Linear HCI+2 User manual

HCI+2
2-Foot Rail Extension
For Use with HCI-12 12-foot “I-beam” Rail
Installation Instructions
1. PRODUCT DESCRIPTION
The Model HCI+2 2-foot “I-rail” extension is designed to be compatible with
the Model HCI-12 12-foot chain-drive “I-rail” used in commercial garage door
installations and in carriage house garage door installations.The 2-foot extension,
when added to the 12-foot “I-rail”, provides a 14-foot long rail for operating high-lift
doors.
The kit includes two “T-rail” sections that bolt together to form an “I-rail” and
connect to the main “I-rail” using two reinforcing straps.The kit also includes two
short lengths of chain to extend the stock chain at the turnbuckle.
2. KIT CONTENTS 3. LOOSEN AND DISASSEMBLE TURNBUCKLE
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,I-RAIL,EXTENTION,2 FT - LINEAR P/N: 228232 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - SCALE: 1-1 - SIDE 1 OF 2
4. REMOVE SPROCKET 5. REMOVE RAIL BOLT 6. IDENTIFY TOP AND BOTTOM EXTENSION RAILS 7. ALIGN REINFORCING STRAPS
8. INSTALL FIRST TWO STRAP BOLTS 9. PLACE BOTTOM EXTENSION RAIL BETWEEN STRAPS 10. ALIGN TOP EXTENSION RAIL BETWEEN STRAPS 11. INSTALL REMAINING TWO STRAP BOLTS
BOTTOM RAIL SECTION
TOP RAIL SECTION
REINFORCING STRAPS(2)
EXTENSION CHAINS(2)
1/4-20 KEPSNUTS(5)
1/4-20 x 13/16" CARRIAGE BOLTS(5)
HOLD SCREWDRIVERIN
TURNBUCKLE SLOT
LOOSEN THE TWO
TURNBUCKLE LOCKING NUTS
NOTE: ONE SIDE OF THE
TURNBUCKLE ISLEFT-HAND
THREAD, THE OTHER SIDE
ISRIGHT-HAND THREAD
UNSCREW AND
REMOVE EACH
END FROM THE
TURNBUCKLE
TOP RAIL SECTION
BOTTOM RAIL SECTION
NOTE: BOTTOM RAIL HASNOTCH ON CORNER!
REINFORCING STRAP #1
REINFORCING STRAP #2
LINE UP SLOTSON THE
REINFORCING STRAPS
WITH THE SLOTSON THE
STOCK I-RAIL
AFTERTHE CHAIN ISLOOSENED,
REMOVE THE SPROCKET HOLDER
FROM THE END OF THE RAIL
LOOSEN THE NUTSAND
REMOVE THE TWO END
BOLTSON THE RAIL
NOTE: BE SURE AND KEEP THE
NUTSAND BOLTS, THEY WILL BE
USED AGAIN LATER
FIT THE TOP RAIL SECTION
BETWEEN THE STRAP ON
THISSIDE AND THE BOTTOM
RAIL SECTION
RAIL EDGES
MUST LINE UP
TOP RAIL SECTION
BE SURE ALL THE
SLOTSARE ALIGNED
STOCK
I-RAIL
USE 1/4-20 x 13/16" BOLTS
AND KEPSNUTSSUPPLIED
INSTALL THE LAST TWO BOLTS
AND NUTSTHROUGH THE
REINFORCING STRAP SLOTS
INSTALL STRAPSON BOTH
SIDESOF I-RAIL
USE 1/4-20 x 13/16" BOLTS
AND KEPSNUTSSUPPLIED
INSTALL BOLT AND NUT
IN THE SECOND SLOT
INSTALL BOLT AND
NUT IN FIRST SLOT
FIT BOTTOM RAIL SECTION
BETWEEN THE TWO
REINFORCING STRAPS
BE SURE ALL THE
SLOTSARE ALIGNED
NOTCH ON THE BOTTOM RAIL
WILL BE ON THISEND, BUTTING
UP TO THE NOTCH ON THE STOCK I-RAIL
BOTTOM RAIL SECTION
STOCK I-RAIL
RAIL EDGESMUST LINE UP
FORSMOOTH TROLLEY
OPERATION

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,I-RAIL,EXTENTION,2 FT - LINEAR P/N: 228232 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - SCALE: 1-1 - SIDE 2 OF 2
12. INSTALL FINAL BOLT 13. REPOSITION THE TROLLEY STOP BOLT 14. TIGHTEN ALL BOLTS 15. REMOVE CHAIN FROM TURNBUCKLE
16. ADD SHORT CHAINS TO TURNBUCKLE 17. RE ASSEMBLE TURNBUCKLE 18. REINSTALL SPROCKET 19. SET TROLLE Y POSITION
20. ADJUST SPROCKET POSITION 21. ADJUST CHAIN TENSION 22. TIGHTEN TURNBUCKLE LOCKNUTS LIMITED WARRANTY
This product is warranted to the original consumer against defects in material and workmanship for
five (5) years. Linear will repair, or at its option, replace, any device that it finds requires service under
this warranty, and will return the repaired or replaced device to the consumer at Linear’s cost. Devices
must be sent to Linear for service at owner’s expense. This warranty does not apply to damage to
the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear or due
to failure to follow Seller’s instructions, or arising from improper installation, storage or maintenance.
In no event will Linear be responsible for incidental, compensatory, punitive, consequential, indirect,
special or other damages. The remedies provided by this warranty are exclusive. Some states do not
allow the exclusion or limitation of incidental and consequential damages, so the above limitation
or exclusion may not apply to you. Any warranties implied by law are limited to the time periods set
forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
For warranty service and shipping instructions contact Linear at the phone number shown below. In
order to be protected by this warranty, save your proof of purchase and send a copy with equipment
should repair be required. All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
SLIP THE SPROCKET HOLDER
ONTO THE END OF THE
EXTENSION RAIL
SET THE TROLLEY DISTANCE
FROM THE PULLEY BRACKET
4 TO 6 INCHES
THE TROLLEY MUST REST 4 TO 6 INCHES
FROM THE PULLEY BRACKET TO MATCH
THE PRE-SET LIMITSIN THE OPERATOR
ADD THE TWO SHORT EXTENSION CHAINS
TO EACH END OF THE STOCK CHAIN
CONNECT THE TWO EXTENSION CHAINS
TO THE TURNBUCKLE EYE-BOLTSUSING
THE MASTERLINKSSUPPLIED
NOTE: ONE SIDE OF THE
TURNBUCKLE ISLEFT-HAND
THREAD, THE OTHER SIDE
ISRIGHT-HAND THREAD
REASSEMBLE THE
TURNBUCKLE AFTER
ADDING THE EXTENSION
CHAINS
BE SURE TO TIGHTEN ALL
THE BOLTSON THE EXTENSION
RAIL ASSEMBLY
REMOVE THE MASTERLINK AND
DISCONNECT THE CHAIN FROM EACH
OF THE TURNBUCKLE EYE-BOLTS
BE SURE TO KEEP THE MASTER LINKS!
THEY WILL BE USED AGAIN
INSTALL THE LAST BOLT
AND NUT INTO THE END SLOT
USE ONE OF THE SHORTER
1/4-20 x 5/8" BOLT AND KEPSNUT
LEFT OVER FROM THE DISASSEMBLY
DONE IN STEP 5
REMOVE THE TROLEY
STOP BOLT AND NUT
FROM THE STOCK I-RAIL
MOVE THE TROLLEY STOP BOLT
AND NUT TO THE BOTTOM
SECTION OF THE EXTENSION RAIL
BOTTOM RAIL SECTION
(TOP VIEW)
STOP BOLT HOLE
HOLD SCREWDRIVERIN
TURNBUCKLE SLOT
TIGHTEN THE TWO
TURNBUCKLE
LOCKING NUTS
NOTE: ONE SIDE OF THE
TURNBUCKLE ISLEFT-HAND
THREAD, THE OTHER SIDE
ISRIGHT-HAND THREAD
ALIGN FLAT ON SPROCKET
THISDIRECTION TO MATCH
FLAT ON OPERATORSHAFT
BE SURE TO KEEP THE TROLLEY
AT 4-6 INCHESFROM THE PULLEY
BRACKET ASSHOWN IN STEP 19
ADJUST THE CHAIN
TENSION WITH THE
TURNBUCKLE
THE CENTEROF THE CHAIN SHOULD BE
SLIGHTLY ABOVE (NO MORE THAN 1/8")
THE BOTTOM EDGE OF THE RAIL
Copyright © 2008 Linear LLC 228232 A