Linksys HG200 User manual

Model No.
HG200
User Guide
WIRELESS
GHz
802.11g
2,4 Gateway
Home Wireless-G

Home Wireless-G Gateway
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
How to Use this Guide
Your Guide to the Home Wireless-G Gateway has been designed to make understanding networking with the
Gateway easier than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.
This exclamation point means there is a Caution or
Warning and is something that could damage your
property or the Gateway.
word: definition.
This checkmark means there is a Note of interest and
is something you should pay special attention to while
using the Gateway.
This question mark provides you with a reminder about
something you might need to do while using the Gateway.
Figure 0-1: Sample Figure Description
HG200_V1.0-UG-50329A JL

Home Wireless-G Gateway
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this User Guide? 2
Chapter 2: Planning Your Network 4
The Gateway’s Functions 4
IP Addresses 4
Chapter 3: Getting to Know the Home Wireless-G Gateway 6
Ports and Reset Button on Side Panel 6
LEDs on Side Panel 7
The Bottom Panel 8
Chapter 4: Connecting the Home Wireless-G Gateway 9
Overview 9
Wired Connection to a Computer 10
Wireless Connection to a Computer 11
Chapter 5: Configuring the Home Wireless-G Gateway 12
Overview 12
How to Access the Web-based Utility 14
The Setup Tab 14
The Wireless Tab 23
The Security Tab 28
The Access Restrictions Tab 30
The Applications and Gaming Tab 32
The Administration Tab 37
The Status Tab 43
Appendix A: Troubleshooting 47
Common Problems and Solutions 47
Frequently Asked Questions 55
Appendix B: Wireless Security 62
Security Precautions 62
Security Threats Facing Wireless Networks 62

Home Wireless-G Gateway
Appendix C: Finding the MAC Address and IP Address for Your
Ethernet Adapter 65
Windows 98 or Me Instructions 65
Windows 2000 or XP Instructions 66
Appendix D: Upgrading Firmware 67
Appendix E: Glossary 68
Appendix F: Regulatory Information 75
Appendix G: Warranty Information 81
Appendix H: Specifications 82
Appendix I: Contact Information 84

Home Wireless-G Gateway
List of Figures
Figure 2-1: Network 4
Figure 3-1: Ports and Reset Button on Side Panel 6
Figure 3-2: LEDs on Side Panel 7
Figure 3-3: Bottom Panel with Stand in Closed Position 8
Figure 3-4: Gateway Using Stand 8
Figure 4-1: Connect the ADSL Line 10
Figure 4-2: Connect a PC 10
Figure 4-3: Connect the Power 10
Figure 4-4: Connect the ADSL Line 11
Figure 4-5: Connect the Power 11
Figure 5-1: Login Screen 14
Figure 5-2: Basic Setup 14
Figure 5-3: RFC 1483 Bridged - Dynamic IP 15
Figure 5-4: RFC 1483 Bridged - Static IP 15
Figure 5-5: RFC 1483 Routed 16
Figure 5-6: RFC 2516 PPPoE 17
Figure 5-7: RFC 2364 PPPoA 17
Figure 5-8: Bridged Mode Only 18
Figure 5-9: Optional Settings 18
Figure 5-10: DynDNS.org 20
Figure 5-11: TZO.com 20
Figure 5-12: Advanced Routing 21
Figure 5-13: Routing Table 22
Figure 5-14: Basic Wireless Settings 23
Figure 5-15: Pre-Shared Key 24
Figure 5-16: WEP 25
Figure 5-17: Wireless Network Access 26
Figure 5-18: MAC Address Filter List 26
Figure 5-19: Wireless Client MAC List 26
Figure 5-20: Advanced Wireless Settings 27
Figure 5-21: Security 28
Figure 5-22: Firewall Log 29

Home Wireless-G Gateway
Figure 5-23: Internet Access 30
Figure 5-24: Internet Policy Summary 30
Figure 5-25: List of PCs 31
Figure 5-26: Add/Edit Service 31
Figure 5-27: Single Port Forwarding 32
Figure 5-28: Port Range Forwarding 33
Figure 5-29: Port Triggering 34
Figure 5-30: DMZ 35
Figure 5-31: QoS 36
Figure 5-32: Management 37
Figure 5-33: Allowed IP - IP Range 37
Figure 5-34: Reporting 39
Figure 5-35: System Log 39
Figure 5-36: Ping Test 40
Figure 5-37: Backup&Restore 40
Figure 5-38: Factory Defaults 41
Figure 5-39: Firmware Upgrade 41
Figure 5-40: Reboot 42
Figure 5-41: Gateway 43
Figure 5-42: Local Network 44
Figure 5-43: DHCP Active IP Table 44
Figure 5-44: ARP/RARP Table 44
Figure 5-45: Wireless 45
Figure 5-46: Networked Computers 45
Figure 5-47: DSL Connection 46
Figure C-1: IP Configuration Screen 65
Figure C-2: MAC Address/Adapter Address 65
Figure C-3: MAC Address/Physical Address 66
Figure D-1: Firmware Upgrade 67

1
Chapter 1: Introduction
Welcome
Home Wireless-G Gateway
Chapter 1: Introduction
Welcome
Thank you for choosing the Home Wireless-G Gateway. This Gateway will provide your computers with a high-
speed Internet connection as well as resources, including files and printers. Since the Gateway is wireless,
Internet access can be shared over the wired network as well as the wireless broadcast at up to 11Mbps for
Wireless-B or up to 54Mbps for Wireless-G.
How does the Gateway do all of this? By connecting the Internet, as well as your computers and peripherals to
the Gateway, then the Gateway can direct and control communications for your network.
To protect your data and privacy, the Gateway features an advanced firewall to keep out Internet intruders.
Wireless transmissions can be protected by powerful data encryption. In addition, you can safeguard your family
with parental control features such as Internet access restrictions and keyword blocking. You can configure the
Gateway’s settings through the easy-to-use, browser-based utility.
But what does all of this mean?
Networks are useful tools for sharing Internet access and computer resources. You can access one printer from
different computers and access data located on another computer’s hard drive. Networks are even used for
playing multiplayer video games. So, networks not only are useful in homes and offices, but also can be fun.
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is
why the network is called “wired”. PCs equipped with wireless cards or adapters can communicate without
cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a
wireless network. This is sometimes called a WLAN, or Wireless Local Area Network. Since the Gateway has
wireless capabilities, it can bridge your wired and wireless networks, letting them communicate with each other.
With your networks all connected, wired, wireless, and the Internet, you can now share files and Internet
access—and even play games. All the while, the Home Wireless-G Gateway protects your networks from
unauthorized and unwelcome users.
Linksys recommends using the Setup CD-ROM for first-time installation of the Gateway. If you do not wish to run
the Setup Wizard on the Setup CD-ROM, then use the instructions in this Guide to help you connect the Gateway,
set it up, and configure it to bridge your different networks. These instructions should be all you need to get the
most out of the Home Wireless-G Gateway.
lan (local area network): The computers and
networking products that make up the network in
your home or office.
nat (network address translation): NAT technology
translates IP addresses of a local area network to a
different IP address for the Internet.
wpa (wi-fi protected access): a wireless security
protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a
RADIUS server.
spi (stateful packet inspection) firewall: a technology
that inspects incoming packets of information before
allowing them to enter the network.
firewall: Security measures that protect the
resources of a local network from intruders.
network: a series of computers or devices
connected for the purpose of data sharing,
storage, and/or transmission between users

2
Chapter 1: Introduction
What’s in this User Guide?
Home Wireless-G Gateway
What’s in this User Guide?
This user guide covers the steps for setting up and using the Home Wireless-G Gateway.
• Chapter 1: Introduction
This chapter describes applications of the Home Wireless-G Gateway and this User Guide.
• Chapter 2: Planning Your Network
This chapter describes the basics of networking.
• Chapter 3: Getting to Know the Home Wireless-G Gateway
This chapter describes the physical features of the Gateway.
• Chapter 4: Connecting the Home Wireless-G Gateway
This chapter instructs you on how to connect the Gateway to your network.
• Chapter 5: Configuring the Home Wireless-G Gateway
This chapter explains how to use the Web-based Utility to configure the settings on the Gateway.
• Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the Home Wireless-G Gateway.
• Appendix B: Wireless Security
This appendix explains the risks of wireless networking and some solutions to reduce the risks.
• Appendix C: Finding the MAC Address and IP Address for your Ethernet Adapter.
This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use
the MAC filtering and/or MAC address cloning feature of the Gateway.
• Appendix D: Upgrading Firmware
This appendix instructs you on how to upgrade the firmware on the Gateway if you should need to do so.
• Appendix E: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix F: Specifications
This appendix provides the technical specifications for the Gateway.
• Appendix G: Warranty Information
This appendix supplies the warranty information for the Gateway.

3
Chapter 1: Introduction
What’s in this User Guide?
Home Wireless-G Gateway
• Appendix H: Regulatory Information
This appendix supplies the regulatory information regarding the Gateway.
• Appendix I: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4
Chapter 2: Planning Your Network
The Gateway’s Functions
Home Wireless-G Gateway
Chapter 2: Planning Your Network
The Gateway’s Functions
A Gateway is a network device that connects two networks together.
In this instance, the Gateway connects your Local Area Network (LAN), or the group of computers in your home or
office, to the Internet. The Gateway processes and regulates the data that travels between these two networks.
The Gateway’s NAT feature protects your network of computers so users on the public, Internet side cannot “see”
your computers. This is how your network remains private. The Gateway protects your network by inspecting
every packet coming in through the Internet port before delivery to the appropriate computer on your network.
The Gateway inspects Internet port services like the web server, ftp server, or other Internet applications, and, if
allowed, it will forward the packet to the appropriate computer on the LAN side.
Remember that the Gateway’s ports connect to two sides. The Ethernet port connects to the LAN, and the ADSL
port connects to the Internet. The Ethernet port transmits data at 10/100Mbps.
IP Addresses
What’s an IP Address?
IP stands for Internet Protocol. Every device on an IP-based network, including computers, print servers, and
Gateways, requires an IP address to identify its “location,” or address, on the network. This applies to both the
Internet and LAN connections. There are two ways of assigning an IP address to your network devices. You can
assign static IP addresses or use the Gateway to assign IP addresses dynamically.
Static IP Addresses
A static IP address is a fixed IP address that you assign manually to a computer or other device on the network.
Since a static IP address remains valid until you disable it, static IP addressing ensures that the device assigned
it will always have that same IP address until you change it. Static IP addresses must be unique and are
commonly used with network devices such as server computers or print servers.
NOTE: Since the Gateway is a device that connects
two networks, it needs two IP addresses—one for
the LAN, and one for the Internet. In this User Guide,
you’ll see references to the “Internet IP address”
and the “LAN IP address.”
Since the Gateway uses NAT technology, the only IP
address that can be seen from the Internet for your
network is the Gateway’s Internet IP address.
However, even this Internet IP address can be
blocked, so that the Gateway and network seem
invisible to the Internet—see the Block WAN
Requests description under Security in “Chapter 5:
Configuring the Home Wireless-G Gateway.”
Figure 2-1: Network
ip (internet protocol): a protocol used to send data
over a network

5
Chapter 2: Planning Your Network
IP Addresses
Home Wireless-G Gateway
Since you use the Gateway to share your DSL Internet connection, contact your ISP to find out if they have
assigned a static IP address to your account. If so, you will need that static IP address when configuring the
Gateway. You can get that information from your ISP.
Dynamic IP Addresses
AdynamicIPaddressisautomaticallyassignedtoadeviceonthenetwork,suchascomputersandprintservers.
These IP addresses are called “dynamic” because they are only temporarily assigned to the computer or device.
After a certain time period, they expire and may change. If a computer logs onto the network (or the Internet) and
its dynamic IP address has expired, the DHCP server will automatically assign it a new dynamic IP address.
DHCP (Dynamic Host Configuration Protocol) Servers
Computers and other network devices using dynamic IP addressing are assigned a new IP address by a DHCP
server. The computer or network device obtaining an IP address is called the DHCP client. DHCP frees you from
having to assign IP addresses manually every time a new user is added to your network.
A DHCP server can either be a designated computer on the network or another network device, such as the
Gateway. By default, the Gateway’s DHCP Server function is enabled.
If you already have a DHCP server running on your network, you must disable one of the two DHCP servers. If you
run more than one DHCP server on your network, you will experience network errors, such as conflicting IP
addresses. To disable DHCP on the Gateway, see the DHCP section in “Chapter 5: Configuring the Home Wireless-
G Gateway.”

6
Chapter 3: Getting to Know the Home Wireless-G Gateway
Ports and Reset Button on Side Panel
Home Wireless-G Gateway
Chapter 3: Getting to Know the Home Wireless-G
Gateway
Ports and Reset Button on Side Panel
The Gateway’s ports and Reset button are located on a side panel.
Line The Line port connects to the ADSL line.
Ethernet The Ethernet port connects to your computer or other network device.
Reset Button There are two ways to reset the Gateway's factory defaults. Either press the Reset Button, for
approximately ten seconds, or restore the defaults from the Factory Defaults screen of the
Administration tab in the Gateway’s Web-based Utility.
Power The Power port is where you will connect the power adapter.
IMPORTANT: Resetting theGatewaytofactory
defaults will erase all of your settings
(including Internet connection, wireless, and
other settings) and replace them with the
factory defaults. Do not reset the Gateway if
you want to retain these settings.
Figure 3-1: Ports and Reset Button on Side Panel

7
Chapter 3: Getting to Know the Home Wireless-G Gateway
LEDs on Side Panel
Home Wireless-G Gateway
LEDs on Side Panel
The Gateway's LEDs, which indicate network activity, are located on the other side panel.
POWER Green. The POWER LED lights up when the Gateway is powered on.
WIRELESS Green. The WIRELESS LED lights up whenever thereis a successful wireless connection. If the
LED is flashing, the Gateway is actively sending or receiving data to or from one of the devices
on the network.
ETHERNET Green. The ETHERNET LED serves two purposes. If the LED is continuously lit, the Gateway is
successfully connected to a device through the Ethernet port. If the LED is flashing, it is an
indication of any network activity.
DSL Green. The DSL LED lights up whenever there is a successful DSL connection. The LED blinks
while the Gateway is establishing the ADSL connection.
INTERNET Green. The INTERNET LED lights up green when an Internet connection to the Internet Service
Provider (ISP) is established. The INTERNET LED lights up red when the connection to the ISP
fails.
Figure 3-2: LEDs on Side Panel

8
Chapter 3: Getting to Know the Home Wireless-G Gateway
The Bottom Panel
Home Wireless-G Gateway
The Bottom Panel
The Gateway has a built-in stand available. If you place the Gateway flat on a surface, then you can leave the
stand in the closed position. However, if you want the Gateway to be upright, swivel the stand clockwise 90º and
position the Gateway accordingly.
Figure 3-3: Bottom Panel with Stand in Closed
Position
Figure 3-4: Gateway Using Stand

9
Chapter 4: Connecting the Home Wireless-G Gateway
Overview
Home Wireless-G Gateway
Chapter 4: Connecting the Home Wireless-G Gateway
Overview
The installation technician from your ISP should have left the setup information for the modem with you after
installing your broadband connection. If not, you can call your ISP to request that data.
After you have the setup information you need for your specific type of Internet connection, you can begin
installation and setup of the Gateway.
If you want to use a computer with an Ethernet adapter to configure the Gateway, continue to “Wired Connection
to a Computer.” If you want to use a computer with a wireless adapter to configure the Gateway, continue to
“Wireless Connection to a Computer.”

10
Chapter 4: Connecting the Home Wireless-G Gateway
Wired Connection to a Computer
Home Wireless-G Gateway
Wired Connection to a Computer
1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.
2. Connect a phone cable from the Line port on the Gateway’s side panel to the wall jack of the ADSL line. A
small device called a microfilter (not included) may be necessary between each phone and wall jack to
prevent interference. Contact your ISP if you have any questions.
3. Connect one end of an Ethernet network cable to one of the Ethernet ports on the back of the Gateway, and
the other end to an Ethernet port on a computer.
Repeat this step to connect a switch, or other network devices to the Gateway.
4. Connect the power adapter to the Gateway’s Power port, and then plug the power adapter into a power outlet.
The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The
Power LED will flash for a few seconds, and then itwill be solidly lit when the self-test is complete. If the LED
flashes for one minute or longer, see “Appendix A: Troubleshooting.”
5. Power on one of your computers that is connected to the Gateway.
Go to “Chapter 5: Configuring the Home Wireless-G Gateway.”
Figure 4-2: Connect a PC
Figure 4-1: Connect the ADSL Line
Figure 4-3: Connect the Power
NOTE: You should always plug the Gateway’s power adapter into a power strip with
surge protection.
NOTE: A small device called a microfilter (not included) may be necessary between each phone and
wall jack to prevent interference. Contact your ISP if you have any questions.
NOTE: This Gateway is intended to replace your existing ADSL modem that already has a microfilter
in place. If this Gateway is not replacing an existing modem, then you will need to purchase a BT
approved microfilter.

11
Chapter 4: Connecting the Home Wireless-G Gateway
Wireless Connection to a Computer
Home Wireless-G Gateway
Wireless Connection to a Computer
If you want to use a wireless connection to access the Gateway, follow these instructions:
1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.
2. Connect a phone cable from the Line port on the Gateway’s back panel to the wall jack of the ADSL line. A
small device called a microfilter (not included) may be necessary between each phone and wall jack to
prevent interference. Contact your ISP if you have any questions.
3. Connect the power adapter to the Power port, and then plug the power adapter into a power outlet.
The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The
Power LED will flash for a few seconds, and then it will be solidly lit when the self-test is complete. If the LED
flashes for one minute or longer, see “Appendix A: Troubleshooting.”
4. Power on one of the computers on your wireless network(s).
5. For initial access to the Gateway through a wireless connection, make sure the computer’s wireless adapter
hasits SSID set to linksys (the Gateway’sdefault setting), and its wireless security isdisabled.After you have
accessedtheGateway,you can change theGateway and this computer’sadapter settings to match yourusual
network settings.
Go to “Chapter 5: Configuring the Home Wireless-G Gateway.”
NOTE: You should always change the SSID from its
default, linksys, and enable wireless security.
NOTE: A small device called a microfilter (not included) may be necessary between each phone
and wall jack to prevent interference. Contact your ISP if you have any questions.
IMPORTANT: Because the microfilter has an RJ-11 connector, except for ISDN users, install the
microfilter between the Gateway and the wall jack.
Figure 4-4: Connect the ADSL Line
Figure 4-5: Connect the Power

12
Chapter 5: Configuring the Home Wireless-G Gateway
Overview
Home Wireless-G Gateway
Chapter 5: Configuring the Home Wireless-G Gateway
Overview
Follow the steps in this chapter and use the Gateway’s web-based utility to configure the Gateway. This chapter
willdescribeeachweb pagein the Utility and each page’skey functions. The utility can be accessed via your web
browserthroughuseofacomputerconnected to the Gateway. For a basic network setup,most users only have to
use the following screens of the Utility:
• Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.
• Management. Click the Administration tab and then the Management tab. The Gateway’s default username
and password is admin. To secure the Gateway, change the Password from its default.
Thereare seven main tabs:Setup,Wireless,Security,Access Restrictions, Applications&Gaming,Administration,
and Status. Additional tabs will be available after you click one of the main tabs.
Setup
• Basic Setup. Enter the Internet connection and network settings on this screen.
• DDNS. To enable the Gateway’s Dynamic Domain Name System (DDNS) feature, complete the fields on this
screen.
• Advanced Routing. On this screen, you can alter NAT and routing configurations.
Wireless
• Basic Wireless Settings. You can choose your wireless network settings on this screen.
• Wireless Security. Configure your wireless security settings on this screen.
• Wireless Access. This screen lets you control access to your wireless network.
• Advanced Wireless Settings. On this screen you can access the advanced wireless network settings.
NOTE: For added security, you should change
the password through the Administration tab.
HAVE YOU: Enabled TCP/IP on your
computers? Computers communicate over the
network with this protocol. Refer to Windows
Help for more information on TCP/IP.

13
Chapter 5: Configuring the Home Wireless-G Gateway
Overview
Home Wireless-G Gateway
Security
On this screen you can disable or enable the firewall, set up filters, block WAN requests, and enable or disable
Virtual Private Networks (VPN) PassThrough.
Access Restrictions
• Internet Access. This screen allows you to control the Internet usage and traffic on your local network.
Applications & Gaming
• Single Port Forwarding. Use this screen to set up common services or applications that require forwarding on
a single port.
• Port Range Forwarding. To set up public services or other specialized Internet applications that require
forwarding on a range of ports, use this screen.
• Port Triggering. To set up triggered ranges and forwarded ranges for Internet applications, click this tab.
• DMZ. To allow one local computer to be exposed to the Internet for use of special-purpose services, use this
screen.
• QoS. Use Quality ofService (QoS) to assign different priority levels to different types of data transmissions.
Administration
• Management. On this screen, alter Gatewayaccess,Simple Network Management Protocol (SNMP), Universal
Plug and Play (UPnP), IGMP-Proxy (IGMP stands for Internet Group Multicast Protocol), and wireless
management settings.
• Reporting. If you want to view or save activity logs, click this tab.
• Diagnostics. Use this screen to run a Ping test.
• Backup&Restore. On this screen, you can back up or restore the Gateway’s configuration.
• Factory Defaults. If you want to restore the Gateway’s factory default settings, use this screen.
• Firmware Upgrade. Click this tab if you want to upgrade the Gateway’s firmware.
• Reboot. If you need to do a hard or soft reboot of the Gateway, use this screen.
vpn (virtual private network): a security
measure to protect data as it leaves one
network and goes to another over the Internet.

14
Chapter 5: Configuring the Home Wireless-G Gateway
How to Access the Web-based Utility
Home Wireless-G Gateway
Status
• Gateway. This screen provides status information about the Gateway.
• Local Network. This provides status information about the local network.
• Wireless. This screen provides status information about the wireless network.
• DSL Connection. This screen provides status information about the DSL connection.
How to Access the Web-based Utility
To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the Gateway’s default
IP address, 192.168.1.1, in the Address field. Then press Enter.
A login screen will appear (Windows XP users will see a similar screen). Enter admin (the default user name) in
the User Name field, and enter admin (the default password) in the Password field. Then click the OK button.
The Setup Tab
The Basic Setup Tab
The first screen that appears is the Basic Setup tab. This tab allows you to change the Gateway's general
settings. Change these settings as described here and click the Save Settings button to save your changes, or
click the Cancel Changes button to cancel your changes.
Internet Setup
• Internet Connection Type. The Gateway supports five Encapsulation methods: RFC 1483 Bridged, RFC 1483
Routed, RFC 2516 PPPoE, RFC 2364 PPPoA, and Bridged Mode Only. Select the appropriate type of
encapsulation from the drop-down menu. Each Basic Setup screen and available features will differ
depending on what type of encapsulation you select.
• VC Settings. You will configure your Virtual Circuit (VC) settings in this section.
• Multiplexing: Select LLC or VC, depending on your ISP.
• QoS Type: Select from the drop-down menu: CBR (Continuous Bit Rate) to specify fixed bandwidth for
voiceor data traffic;UBR (UnspecificBitRate)for application that are none-time sensitive,suchas e-mail;
or VBR (Variable Bite Rate) for Bursty traffic and bandwidth-sharing with other applications. Figure 5-2: Basic Setup
Figure 5-1: Login Screen