Linksys HomeLink HPPO200 User manual

HomeLink
™
Series
Phoneline 10M
Cable/DSLRouter
User Guide
Use this guide to install: HPRO200

COPYRIGHT & TRADEMARKS
Copyright © 2001 Linksys, All Rights Reserved. HomeLink is a registered trademark of
Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of
Microsoft Corporation. All other trademarks and brand names are the property of their
respective proprietors.
LIMITED WARRANTY
Linksys guarantees that every HomeLink Phoneline 10M Cable/DSL Router is free from
physical defects in material and workmanship under normal use for one (1) year from the
date of purchase. If the product proves defective during this warranty period, call Linksys
Customer Support in order to obtain a Return Authorization number. BE SURE TO HAVE
YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. RETURN REQUESTS CAN-
NOT BE PROCESSED WITHOUT PROOF OF PURCHASE. When returning a product,
mark the Return Authorization Number clearly on the outside of the package and include
your original proof of purchase. All customers located outside of the United States of
America and Canada shall be held responsible for shipping and handling charges.
IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PROD-
UCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM-
AGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFT-
WARE, OR ITS DOCUMENTATION. Linksys makes no warranty or representation,
expressed, implied, or statutory, with respect to its products or the contents or use of this
documentation and all accompanying software, and specifically disclaims its quality,
performance, merchantability, or fitness for any particular purpose. Linksys reserves the
right to revise or update its products, software, or documentation without obligation to
notify any individual or entity. Please direct all inquiries to:
Linksys P.O. Box 18558, Irvine, CA 92623.
FCC STATEMENT
The HomeLink Phoneline 10M Cable/DSL Router has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment or device
• Connect the equipment to an outlet other than the receiver’s
• Consult a dealer or an experienced radio/TV technician for assistance
UG-HPRO200-00103A KL

Phoneline 10M Cable/DSL Router
Troubleshooting 30
Common Problems and Solutions 30
Frequently Asked Questions 32
Appendix 36
How to Ping Your ISP’s E-mail & Web Addresses 36
Installing the TCP/IP Protocol 38
Twisted Pair Cabling 41
Crimping Your Own Network Cables 42
Glossary 43
Specifications 48
Environmental 49
Warranty Information 50
Contact Information 51
HomeLink™ Series
Table of Contents
Introduction 1
The Linksys HomeLink Phoneline 10M Cable/DSL Router 1
Features 1
Package Contents 2
System Requirements 2
Getting to Know the HomeLink Phoneline
10M Cable/DSL Router 3
The HomeLink Phoneline Router’s Rear Panel Ports 3
The HomeLink Phoneline Router’s Front Panel LEDs 4
Using the HomeLink Phoneline 10M Cable/DSL Router 7
Installation Overview 7
Connecting the HomeLink Phoneline Router to Your Network 8
Daisy-chaining a HomeLink Network 9
Resetting the HomeLink Phoneline Router 10
Configuring Your Ethernet Network with the
HomeLink Phoneline 10M Cable/DSL Router 11
Configuring the HomeLink Phoneline Router 11
Configuring Your Windows 95 & 98 PCs to Connect to the HomeLink
Phoneline Router 14
The HomeLink Phoneline 10M Cable/DSL
Router’s Web-Based Utility 17
Quick & Easy Administration 17
Setup 18
Password 20
Status 21
DHCP 22
Help 23
Filters 24
Forwarding 25
Dynamic Routing 26
Static Routing 27
DMZ Host 29

Phoneline 10M Cable/DSL Router
• One HomeLink™ Phoneline 10M Cable/DSL Router
• One AC Power Adapter
• One User Guide and Registration Card
• Windows 95, 98, Millennium, NT 4.0, or 2000
• Pentium-Grade CPU or better
• 32 MB of RAM
• Microsoft IE 4.0 or higher, Netscape Navigator 4.06 or higher
• An Ethernet or Home Phoneline Adapter withTCP/IP Protocol for each PC
2
Package Contents
System Requirements
Introduction
The HomeLink™ Phoneline 10M Cable/DSL Router provides the perfect solu-
tion for connecting to high-speed broadband Internet through your existing
telephone lines. This HomeLink™ Phoneline 10M Cable/DSL Router from
Linksys acts as the only externally recognized Internet gateway on your Local
Area Network (LAN) and can be configured to regulate internal users’ access
to the Internet and serve as an Internet firewall against unwanted outside
intruders.
Do you want to share your cable or DSL modem on your HomeLink™
Phoneline network? Add a PC anytime by simply connecting it to a telephone
jack in your wall, providing for instant communication throughout your home.
The groundbreaking technology inside every HomeLink™ Phoneline 10M
Cable/DSL Router delivers Internet and network connectivity at speeds of up
to 10Mbps.
• Share Your Cable/DSL Connection with Every PC in Your House Using
Standard Telephone Lines
• Bridge Your Home Phoneline Network to an Ethernet Network and Share
Broadband Access Between Them
• Add a PC to Your Home Network Simply By Plugging Your PC’s Home
Phoneline Network Adapter Into a Standard Phone Jack
• Provides Exceptional Network Security with the Built-In NAT Firewall
• An All-In-One Box for Internet Sharing Through Ethernet and Home
Phoneline Networks
• Easy Manageability Through Your Web Browser
• SecureYour Network With Network Address Translation (NAT)
• Works With Your PC’s Home Phoneline Network Adapter to Create an
Internet-Sharing Home Network
• Supports Port Filtering, IP Filtering, and MAC Filtering
• Built-In Ethernet-to-Home Phoneline Network Bridge for Local Computer
Connections
• Fully HomePNA 1.0, 1.1 and 2.0-Compatible
• Easy Installation—No Software Required
• FreeTechnical Support—24 Hours a Day, 7 Days a Week for North America
Only
• 1-Year Limited Warranty
The Linksys HomeLink™ Phoneline 10M Cable/DSL Router
Features
1
HomeLink™ Series

Phoneline 10M Ethernet Bridge
4
Getting to Know the HomeLink
Phoneline 10M Cable/DSL
Router
Rear Panel Ports
Phone Use this port for connecting your telephone. It employs a
microfilter for signal clarity. Do not plug your telephone into
any of the other ports.
HPNA Use the HPNA ports to connect your Home Phoneline Router
to your HomeLink network. These ports are configured as
pass-through ports, meaning that the network data travels into
the Home Phoneline Router through one of the HomeLink
ports, then continues out the other. Connect one HomeLink
telephone cable into one of the ports, then continue (with
another cable) to your next HomeLink device through the
port's other side.
LAN Connect an Ethernet PC (or an Ethernet device) to your
HomeLink phoneline network through one of the HomeLink
Phoneline Router’s 10BaseT ports.
WAN Share your Internet access over your entire Home Phoneline or
Ethernet network by connecting to your DSL or Cable modem
through the Home Phoneline Router’s WAN port. The Uplink
port can also connect to Ethernet devices such as hubs, routers,
and switches. If the Uplink port is used, the port right next to
it (LAN) will be inoperable. Any connections made through a
LAN will be lost.
3
HomeLink™ Series
The HomeLink Phoneline Router’s Rear Panel Ports
Crossover Switch The Crossover Switch (X II) toggles the LAN port
between crossover mode (X) and straight-through mode
(II). If you are connecting the Router directly to a com-
puter or to an Uplink port, choose crossover (X). For any-
thing else, choose straight-through (II).
Power Connect your power adapter to your HomeLink
Phoneline Router through the Power port.
The Reset Button*
Briefly pressing the Reset Button will refresh the HomeLink
Phoneline Router’s connections, potentially clearing any jammed
links.
Pressing the Reset Button and holding it in for a few seconds will clear all of
the HomeLink Phoneline Router’s data and settings. This should be done only
if you are experiencing heavy routing problems, and only after you have
exhausted all of the other troubleshooting options. By resetting the HomeLink
Phoneline Router, you run the risk of creating conflicts between your PCs’
actual IP Addresses and what the HomeLink Phoneline Router thinks their IP
Addresses should be. You may be forced to reboot the entire system(s).
If your HomeLink Phoneline Router locks up, simply power it down for 3 to 5
seconds by removing the power cable from the Router’s Power Port. Leaving
the power off for too long could result in the loss of network connections.

Power The Power LED will light up when the HomeLink
Phoneline Router is powered on. Note that there is no
ON/OFF switch; simply plug in the power adapter.
The LAN Indicators
Link/Act Green. The Link/Act LED serves two purposes. If the
LED is continuously illuminated, the HomeLink
Phoneline Router is successfully connected to a device. If
the LED is flickering, the Router is actively sending or
receiving data over that port.
Full/Col Green. The Full/Col LED also serves two purposes. If
this LED is continuously illuminated, the connection is
successfully running in Full Duplex mode. If the LED is
flickering, the connection is experiencing collisions.
Infrequent collisions are normal. If this LED is flickering
too often, there may be a problem with your connection.
Check the Troubleshooting section if you think there is a
problem.
100 Orange. The 100 LED illuminates when a successful
100Mbps connection is made through the corresponding
port.
Linksys HomeLink™ Series
5
Phoneline 10M Cable/DSL Router
6
The HomeLink Phoneline Router’s Front Panel LEDs The WAN Indicators
Link Green. The Link LED illuminates when a successful
connection is made between the HomeLink Phoneline
Router and your Broadband device or network.
Act Green. The Act LED flickers when the HomeLink
Phoneline Router is sending or receiving data over the
broadband port.
Diag Red. The Diag LED illuminates when the HomeLink
Phoneline Router goes through its self-diagnosis mode
during boot-up. It will turn off upon successful comple-
tion of the diagnosis. If this LED stays on for an abnor-
mally long period of time, refer to the Troubleshooting
section.
The HPNA Indicators
Link A Link LED will light up when the port successfully
connects to your phoneline network.
Act Green. The Act LED flickers when the HomeLink
Phoneline Router is sending or receiving data over the
HPNA port.
Col If the Col LED is flickering, the connection is experienc-
ing collisions. Infrequent collisions are normal. If this
LED is flickering too often, there may be a problem with
your connection. Check the Troubleshooting section if
you think there is a problem.

The following instructions will have your HomeLink Phoneline Router up and
running in minutes.
Basic Installation
1. Make sure that every component of your network (including any PCs
and the HomeLink Phoneline Router) is powered off.
2. Connect your Ethernet device to the HomeLink Phoneline Router
through the HomeLink Phoneline Router’s LAN port. If you have several
Ethernet devices, connect the HomeLink Phoneline Router to a 10/100
Ethernet hub or switch. Ethernet devices should be connected to the
HomeLink Phoneline Router with a network cable that is less than 100
meters (328 feet) in length.
3. Connect the network cable from your Cable or DSL modem to the WAN
port on the rear of the HomeLink Phoneline Router.
4. Connect the HomeLink Phoneline Router to the HomeLink network by
connecting telephone cable, plugged into your home’s telephone jacks, to
one of the HomeLink Phoneline Router’s HPNA ports. The entire length of
telephone cable used in a HomeLink network should never exceed 300
meters (1000 feet).An addition HPNA port and LAN port is provided if you
prefer to daisy-chain the PCs in your home network. For more detailed
information on daisy chaining, see the next page.
5. Power everything on. Connect the supplied power cord to the power
adapter, then to the Power port on the rear of the Homelink Phoneline
Router. Plug the power cord into an electrical outlet.
The HomeLink Phoneline 10M Cable/DSL Router installation is now
complete.
Using the HomeLink Phoneline
10M Cable/DSL Router
Since the HomeLink Phoneline 10M Cable/DSL Router is a stand-alone device
that requires no software or system configuration, its setup involves nothing
but plugging everything in and turning all your hardware on. However, there
are a few limitations to the amount of physical distance your network can cover
without running the risk of data corruption. These restrictions are due to Home
Phoneline and Ethernet standard limits on the recommended length of your net-
working cables, as shown below.
Ethernet Cabling
Although there are different grades of Ethernet network cabling, you should
use UTP Category 5 (unshielded twisted-pair) cables for each Ethernet con-
nection you make, and no Ethernet cable should exceed 100 meters (328 feet)
in length. Category 5 cabling is available at most computer stores, or you can
crimp your own network cables. See the Crimping Your Own Network
Cables section of the Appendix for details on crimping.
HomeLink Phoneline Cabling
Due to the limitations of standard telephone cables, HomeLink phoneline
devices require that no network of HomeLink cabling exceeds a total length of
300 meters (1000 feet). In other words, if you have more than 500 feet of tele-
phone wires connecting your network, you will be more likely to experience
data loss.
Any standard telephone cable will do.
Phoneline 10M Cable/DSL Router
8
Connecting the HomeLink Phoneline Router to Your Network
NNoottee: Power everything off before connecting PCs to the
HomeLink Phoneline Router. If both the PC and the Router are
powered on when the initial connection is made, the network may
act erratically and you will have to reset the Router.
7
HomeLink™ Series
Installation Overview

If your network connections begins acting erratically, you may want to reset the
Homelink Phoneline Router.
To reset your Homelink Phoneline Router, do the following:
1. Shut down all of your network components.
2. Disconnect the Homelink Phoneline Router’s power supply and wait five
seconds.
3. Plug the Homelink Phoneline Router’s power supply back into the power
outlet.
Daisy-chaining your HomeLink PCs and peripherals can create a simple net-
work that acts in the same way an Ethernet network acts on your PC's desktop.
While Ethernet networks usually revolve in a star topology around a hub or
switch, phoneline networks link together like a string of Christmas lights. In a
HomeLink network, data passes into on one side of a port, and a new telephone
cable continues out from the port’s other side. You can string up to 30 PCs on
a single HomeLink network, provided that the entire length of cable does not
exceed 300 meters (1000 feet).
HomeLink networks can send data through existing telephone lines without
disrupting your telephone service, connecting over your existing telephone
jacks. If you have PCs on two different floors of your house, plug one of the
downstairs PCs into the phone jack in the wall, and you're able to network your
PCs upstairs without running excessive amounts of extra cable.
Phoneline 10M Cable/DSL Router
10
Resetting the HomeLink Phoneline Router
9
HomeLink™ Series
Daisy-chaining a HomeLink Network

3. The HomeLink
Phoneline 10M
Cable/DSL
Router’s Setup
page will appear.
4. Configure the following values.
Router Name & Domain Name These fields allow you to supply a host
and domain name for the HomeLink Phoneline Router. Some ISPs require
these names as identification. You may have to check with your ISP to see
if your Broadband Internet service has been configured with a host and
domain name. In most cases, leaving these fields blank will work.
Configuring Your Ethernet
Network with the HomeLink
Phoneline 10M Cable/DSLRouter
Now that your HomeLink Phoneline Router is wired into your network, you
can begin configuring your system.
1. Open your web browser and type
http://192.168.1.1 in the browser’s Address
box. This number is the default IP address of the
HomeLink Phoneline Router. Press the Enter key.
2. A username and password prompt will appear. Leave the User Name box
empty and type admin (the default password) in the Password box. Click
the OK button.
Phoneline 10M Cable/DSL Router
12
NNoottee::If you have previously enabled an Internet Sharing
Proxy Service on any of your PCs, you must disable it
now.
• If you are running Netscape Navigator: Click EEddiitt>> PPrreeffeerreennccee>>
AAddvvaanncceedd>> PPrrooxxiieess> and click DDiirreeccttCCoonnnneeccttiioonnttootthheeIInntteerrnneett.
• If you are running Internet Explorer v5 or better, click SSttaarrtt>>
SSeettttiinnggss>> CCoonnttrroollPPaanneell>> IInntteerrnneettOOppttiioonnss>> CCoonnnneeccttiioonnss>> LLAANN
SSeettttiinnggss. Remove the checks from all three boxes. Click OOKKto con-
tinue.
11
HomeLink™ Series
Configuring the HomeLink Phoneline Router
NNoottee::
If the TCP/IP
protocol is not con-
figured on your PC,
go to the Appendix
for TCP/IP installa-
tion instructions now.

7. Unless you already have a DHCP server on your internal network, choose
Enable from the DHCP Server field. By choosing Enable, you will con-
figure the HomeLink Phoneline Router to automatically assign IP address-
es to each of your PCs. In the Number of DHCP Users box, enter the num-
ber of PCs you plan on networking to the HomeLink Phoneline Router, or
leave it alone. Don’t forget to change this number if, in the future, you add
more PCs to your network.
8. Click the Apply button, then click the Continue button.
9. Reset the power on the cable or DSL modem, then restart the computer
so the computer can obtain the new HomeLink Phoneline Router’s IP infor-
mation.
Your HomeLink Phoneline Router is now configured to your network.
Please continue to the following section to complete your network setup.
Now that the HomeLink Phoneline Router is configured, you will have to con-
figure your other PCs to accept the IP addresses that the HomeLink Phoneline
Router will provide.
These instructions apply only to Windows 95, 98, and ME
machines. For TCP/IP setup under Windows NT and 2000, please
refer to your Windows manual.
1. Click the Start button, select Settings, then click on Control Panel.
2. Double-click the Network icon.
LAN IPAddress These values refer to
your internal network settings. Unless
you have specific internal needs, there
should be no reason to change these
values. For the internal LAN, the
default values are as follows.
• Private IP Address: 192.168.1.1
• Subnet Mask: 255.255.255.0
WAN IPAddress These values refer to the outside network you connect to
every time you access your Broadband Internet connection. Most
Broadband ISPs assign their clients with a different IP address each time
they log on. If this is the case with your ISP, click Obtain an IP Address
Automatically and continue to step 5. If your ISP assigns you a fixed IP
address, click Specify an IP Address and enter the address into the Subnet
Mask, Default Gateway Address and DNS fields provided by the ISP.
If you need to enable PPPoE support, choose Enable. If you do
enable PPPoE, remember to remove any existing PPPoE applica-
tions already on your computer. (More information on PPPoE can
be found in the Setup section for the Web-based Utility.)
5. When you have properly configured the Setup page, click the Apply but-
ton, then click the Continue button.
6. Choose the DHCP tab.
Phoneline 10M Cable/DSL Router
14
Configuring Your Windows 95 & 98 PCs to Connect
to the HomeLink Phoneline Router
13
HomeLink™ Series
NNoottee::
If you have an existing DHCP
server on your LAN and you don’t
wish to use the HomeLink Phoneline
Router as your new DHCP server, you
must assign Router a static IP
address. The Router’s IP address
must be compatible with your existing
network. You can not have two DHCP
servers running on one LAN at the
same time.