LinTronic TT455-RT-238 Installation instructions

TT455-RT-238
Signal Converter
Hardware version 6 / 6.1
Updated 180822
LinTronic

Hardware 4
Hardware 5
We keep expanding
Introduced 2003
Introduced 2006
Introduced 2011
Hardware 6
32KByte 128KByte 256KByte
LinTronic

Feature Hardware 5 Hardware 6
Built-in 455 KHz receiver for B&O Yes No
External 455 KHz receiver required for B&O No Yes
Reading IR receivers buttons No Yes
Number of RS232 comports 1 2
Ready for B&O Masterlink Gateway No Yes
Number of low-power IR outputs 1 2
Programmable IR low-power outputs No Yes
Filters BEO4/BEO5 long-codes No Yes
Flash program size 128KB 256KB
Control of IR receivers LEDs No Yes
Programmable RS232 signals/port No Yes
Programmable IR high-power output No Yes
B&O 455 KHz transmitter software soft/hardware
RS485 Yes No
X10 port Yes No
Volatile memory (SRAM) 4KB 8KB
Non-volatile memory (EEPROM) 4KB 4KB
Multi-purpose Timers 3 5
What's new ?
LinTronic

What's new ?
LinTronic
31. July 2018
We added support for this 8-channel relay.
See section about RS232.

Hardware Version
5.0
Hardware Version
6.1
940 NM
850 NM
Hardware 6.1 includes a new 3 volt IR LED
with 30% more light adding 30% to the
original range.
When controlling B&O systems, this increases
the operation range to beyond BEO4 level.
LinTronic

Circuit boards dimensions
59 mm
93 mm
16 mm
RED LED GREEN LED 1
GREEN LED 2
940 nM 850 nM 940 nM
LinTronic

IR RECEIVER
1
2
3
1
2
3
Programmable jack-connector
IR BUTTONS/LED
FACTORY DEFAULT
v
v
Button 1
Button 2
Button 3
Button 4
LED 1
LED 2
IR LOW-POWER OUTPUT 2
LinTronic
1
2
3
1
2
3

A B C
Pin Letter Desc Color
3 B IR data Green
4 C 5 Volt Yellow
5 A Ground Brown
TT-IR-8087030 IR RECEIVER
3
4
5
NOTE:
The IR receiver (alu case) and the cable, are delivered to us separately.
Unfortunately the cable wires, often vary in colors.
Below we have listed the typical combinations.
If the cable you have received, is not included below, then please contact
LinTronic, or get some local help to measure how the cable is wired.
Pin Letter Desc Color
3 B IR data Red
4 C 5 Volt Black
5 A Ground unisolated
Cable type 1
Cable type 2
1
2
3
4
5

53443
5
Jack connector seen
from solderside
3 = IRsignal
4 = 5 volt
5 = Ground
TT-IR-8087030
5 4 3 2 1
2 1
1 - CLOCK
2 - DATA
1
2
Jack connector seen
from solderside
Not used
Not used
Infrared/power
Buttons/LEDs
If you want to make use of the buttons or the
LEDs of your external B&O receiver,
the jumpers must be in this position (factory
set).
You wire two 3.5 mm jack connectors as show
below:
- one for the infrared signals (3-wires, pin 3-5)
For the buttons/LEDs you may optionally use a
stereo connector or a mono-connector. It is
easier to verify that connectors are correctly
inserted if you use a mono-connector for the
buttons.
- one for the buttons/LEDs (2-wires, pin 1-2)
2 1
Stereo
Mono
IR AND BUTTONS CONTROL
LinTronic
Programmable jack-connector

53443
5
Jack connector seen
from solderside
3 = IRsignal
4 = 5 volt
5 = Ground
5 4 3 2 1
1 - CLOCK
2 - DATA
1
2
Jack connector seen
from solderside
Not used
Buttons/LEDs
If you only want to control the TT455-RT-238 by
the buttons on the front of the external receiver,
you will still need to install both connectors.
The data wire carrying the IR signal can be
leaved out.
BUTTONS CONTROL ONLY
TT-IR-8087030
Infrared/power
2 1 Mono
LinTronic
Programmable jack-connector

A B C
A
Jack connector seen
from solderside
3 - B IR SIGNAL
4 - C 5 Volt
5 - A Ground
B&O
8087030
TO TT455-RT-238
OR BEOSYSTEM A
Ground
IR/DATA
B
A
Jack connector seen
from solderside
AB
USING ONE RECIVER FOR TWO SYSTEMS
Do not connect center, 5 volt
IR receiver
TO TT455-RT-238
OR BEOSYSTEM B
LinTronic
BC
1
2
3
4
5

IR RECEIVER
IR LOW-POWER 1IR LOW-POWER 2
IR TRANSMITTER FRONT
IR receivers & transmitters
IR TRANSMITTER
IR FRONT BOOSTER
IR LOW-POWER 1
IR LOW-POWER 2
3-CHANNEL SOFTWARE PROGRAMMABLE IR DISTRIBUTOR
50% or 100%
LEVEL
B&O 455 KHz oscillator
LinTronic
IR LOW-POWER OUTPUT 2
1
2
3
1
2
3

Output Power Communication Input Output
TT-IR-ET02
TableTop
Transmitter or Converter
2 pcs low-power
IR outputs
External low-power IR output
LinTronic

5 4 3 2 1
9 8 7 6
Gnd
Rx (in)
Tx (out)
Digital Inputs
5 volt pulled-up. 100K
Digital Outputs
active low, 5 volt pulled-up
Gnd
Gnd
1
2
1
2
Gnd
Rx (in)
Tx (out)
RS232 PORT 2
Programmable
RS232 PORT 1
RS232 comports
RS232 COMPORT 2
SOFTWARE PROGRAMMABLE RS232 DISTRIBUTOR
RS232 COMPORT 1
LinTronic

RS232 comports
Relay Control
LinTronic
2
3
5
2
3
5
Crossed cable
8 x relays
Functionality can be configured to work as:
- 8 individual relays on/off (for example light)
- 4 paired relays (for example curtains, lifts, motors)
Activate the wanted relay and it will turn off automatically when wanted.
Timing can easily be adjusted in the configurator:
TT455-RT-238 - RELAY 208
For operation and timing - see manuals for RELAY 208:
http://lintronic.dk/getstarted.aspx
Relays can be operated by B&O remote:
- numbers, 0 - 9
- colors, Red, Green, Yellow, Blue - short or long push
MaleMale

Digital Inputs 5 volt
1 or 4
5
The digital Input is internally pulled up by a 100 Kohm resistor. In order to activate the
input, the input pin 1, must be grounded.
The TT455-RT-238’s digital inputs can be configured to react to both ON and OFF.
This allows you to activate one action when the input is activated and another action
when the input is released.
For example:
1) Connect a motion PIR detector and let the TT455-RT-238 control your light
system by RS232 when the PIR is activated or deactivated.
2) Used by some dealers:
An outside motion sensor, turn on the TV and play a DVD when people pass by
the window.
100K
Digital Inputs
LinTronic
5 4 3 2 1
9 8 7 6

Digital Outputs
LinTronic
The digital outputs
are programmable
in the in/out tab,
in Memory Map
of the Configurator.
Outputs can work as:
Active 12 volt (default)
or
Active Ground
or
Ative Ground with 5 volt pull-up

5 4 3 2 1
9 8 7 6
Active 12 volt
Pin 6 = digital output 1
Pin 9 = digital output 2
Pin 5 = Ground
12 volt
3R3
Digital Outputs, Active 12 volt
SCHRACH
Can be screwed
to the wall or
mounted in a
DIN rail.
Side view Front view
11
14
21
24
1222
A1
A2
NC
COIL
NO
COM
A2
A1
The digital outputs are designed for direct control of 12 V relays.
This can be used to control lamps, curtains, motors, etc.
We offer Schrack relays and DIN/WALL mount housing.
LinTronic

Pin 6
Digital output 1
Pin 5 = Ground
12 volt
3R3
Digital Output 1, Active 12 volt
SCHRACH
11
14
21
24
1222
A1
A2
NC
COIL
NO
COM
LinTronic
Pin 9
Digital output 2
Pin 5 = Ground
12 volt
3R3
Digital Output 2, Active 12 volt
SCHRACH
11
14
21
24
1222
A1
A2
NC
COIL
NO
COM
5 4 3 2 1
9 8 7 6
5 4 3 2 1
9 8 7 6

TT455-RT-238
digital output
5
12 volt
3R3
SCHRACH
Front view
11
14
21
24
1222
A1
A2
NC
COIL
NO
COM
115 - 230 vac
50/60 Hz
(fused)
Example on how the TT455-RT-238 may control a 115/230 vac lamp on/off.
Run the fused phase (brown) to pin 11 (lamp 1) and pin 21 (lamp 2).
Run pin 14 (on/off output for lamp 1) to lamp 1.
NOTE:
In some countries - by law - only an electrician may install 115/230 vac.
Run the neutral/ground (can have different names) to lamp 1 and lamp 2.
Run pin 24 (on/off output for lamp 2) to lamp 2.
Run TT455-RT-238's digital output 1 (or 2) to A2 (coil) of the relay.
Run TT455-RT-238's ground to A1 (coil) of the relay.
The TT455-RT-238 is totally isolated from the 115/230 vac due to the relay.
2 lamps
LinTronic
Digital Outputs, Active 12 volt