LITESUN ELECTRONICS LTS-W3 User manual
LTS-W3 User Manual
1. Product parameter
USB Output DC5V/3.4A（total） Each USB Output is 2.1A
Wireless charging
Output Power Qi-EPP 10W Max
Input voltage AC125V/60Hz
Protect function Over temperature protection, FOD foreign object detection
2.Description of wireless charging function
The indicator status is described in the following table：
status Power-on Standby Charging After full Metal foreign
body detection
Indicator
status bright Always
off
Breathing
state Everbright Flash 1s / time
1625W
2.1 Put the mobile phone with wireless charging function (such as
iPhone11 /12/13, Samsung Note8/S9+, Huawei mate30Pro, etc.) to the center of
wireless charging and the charging will start automatically. When the wireless charger
is in normal working condition, the LED green light blink slow.
2.2 When charging, you need to keep the center position of the phone aligned with
the center position of the wireless charger to perform wireless charging. If it is not
working properly, please adjust the position of the phone until the phone shows
normal charging or the LED green light blink slow.
3.Notes
Do not mix metal foreign objects between the phone and the wireless
charger while charging.
In order to ensure normal charging, the thickness of the plastic or silicone mobile phone
case is less than1-2mm. The material and thickness of the phone case can affect
the normal charging function and increase the temperature of the wireless charging. If
necessary, remove the phone case for wireless charging.
Do not squeeze or bump the product.
Do not disassemble or modify it by yourself.
Do not place the product near fire or into fire or water.
Do not use the wireless charger under severe heat, humidity or corrosive conditions to avoid
damage to the circuit.
Do not place the magnetic card (ID card, bank card, etc.) with a magnetic strip or chip too
close to avoid the magnetic card failure.
Keep implanted medical devices (cardiac pacemakers, implantable cochlea, etc.) at least 20
cm away from the wireless charger to avoid potential interference with medical equipment.
Children should be taken care to avoid unnecessary accidents.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This device complies with part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.unde
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment .This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or mormore of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
1
ISED RSS Warning/ISED RF Exposure Statement
ISED RSS Warning: This device complies with Innovation, Science and Economic
DevelopmentCanadalicence‐exemptRSSstandard(s).Operationissubjecttothe
followingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)this
devicemustacceptanyinterference,includinginterferencethatmaycauseundesired
operationofthedevice.
LeprésentappareilestconformeauxCNRd'ISEDapplicablesauxappareilsradio
exemptsdelicence.L'exploitationestautoriséeauxdeuxconditionssuivantes:
(1)l'appareilnedoitpasproduiredebrouillage,et(2)l'utilisateurdel'appareil
doitacceptertoutbrouillageradioélectriquesubi,mêmesilebrouillageest
susceptibled'encompromettrelefonctionnement.
ISED RF exposure statement:
ThisequipmentcomplieswithISEDradiationexposurelimitssetforthforan
uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwith
minimumdistance20cmbetweentheradiator&yourbody.Thistransmittermustnot
beco‐locatedoroperatinginconjunctionwithanyotherantennaortransmitter.
LerayonnementdelaclassebrepecteISEDfixaientunenvironnementnon
contrôlés.Installationetmiseenœuvredecematérieldevraitavecéchangeur
distanceminimaleentre20cmtoncorps.Lanceursounepeuventpascoexistercette
antenneoucapteursavecd’autres.
Table of contents
