Lockly Vision User manual

VISION™
DEADBOLT EDITION
INSTALLATION
GUIDE

Go to lockly.com/pages/installation to watch a
video version of this installation guide.
Download the BILT app in the Apple or Google Play
store for step-by-step interactive 3-D walk-through
installation instructions.
OR

Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly Vision up and running.
Installation generally takes less than 30 minutes. If
you have any questions please reference our online
support at: Lockly.com/support or call [phone]
for help.

CAUTION: lock contains electrostatic-sensitive (ESD) parts. Best practices: ground yourself by
touching a metal surface other than lock to discharge any ESD you might have; don't wear
clothes prone to static (ESD); avoid touching electronic internal pins and circuit board.
Prepare door: remove existing deadbolt or use provided template to bore new holes.
3
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
1-⅜" (35mm)
to 2" (50mm)
1" (25mm)
2-⅜" (60mm)
or
2-¾" (70mm)
Cross-bore
2-⅛" (54mm)
Preparation

4
Deadbolt slot must align to the center of the door hole. Adjust as shown if needed.
The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary.
(wear gloves to protect from possible pinching).
Hold the metal plate and
twist the deadbolt body
clockwise till it snaps to 2-3/8"
Deadbolt comes set
at 2-3/4" (70mm). To return to
default, while deadbolt is
extended, hold the metal
plate and twist the dead-
bolt body counter-clock-
wise till it snaps to 2-3/4"
Push the crank to
extend the deadbolt
ADJUST DEADBOLT AND INSTALL
Step 1
B
B
B
B
A
C
C
C
D
D
D
D
A
2-3/4" (70mm)
or 2-3/8” (60mm)

5
Extend the deadbolt by inserting a
flat-head screwdriver into the slot and
turning clockwise.
Insert the deadbolt into mortise flush with
door edge, make sure that the right side is
up and the slot is in the vertical position.
Secure with 2 screws.
(2X)
K
K
ADJUST DEADBOLT AND INSTALL
Step 1 continued
1
2

INSTALLING EXTERIOR ASSEMBLY (B)
6
Check the exterior assembly (B) align-
ment to door hole and deadbolt before
peeling off film on adhesive strips.
Peel film from adhesive strips and make sure torque blade is in the vertical position with
the deadbolt extended. Place assembly and torque blade through the deadbolt slot
and guide connection cables through the cross-bore hole under the deadbolt as shown.
Complete mounting by aligning and securing until flush to exterior door surface.
Step 2
Vertical
Extended
EXTERIOR VIEW
Under

INSTALLING INTERIOR ASSEMBLY (G)
7
1: Check interior mounting plate (K)
alignment to your door hole before
securing with adhesive strips.
3: Insert and tighten by hand 2
screws located on the left and right of
the blade. Check alignment and
tighten with screwdriver until mounting
plate is securely placed on door.
TIP: when installing screws by hand, turn screws clockwise several turns then
counterclockwise one turn to ensure smooth threading and no cross threading.
4: Use the key to ensure deadbolt locks and
unlocks smoothly (no binding or rubbing).
IMPORTANT: when finished, leave the dead-
bolt extended and remove the key before
proceeding to the next step.
2: Align and secure mounting plate with
adhesive strips. Guide connection cables
through the hole and secure to the lower
left notched hole.
2X
F
F
Step 3
Remove key when finished
Leave deadbolt extended

8
Lockly Vision™comes with a pre-wired door sensors consisting of two parts:
Part (P) - Wired Sensor Part (Q) - Sensor Magnet
About door sensors
Door sensors provide real-time door condition status, such as the ability to verify if
the door is securely closed. It also sends push notifications to your phone whenever
your door opens and enables voice control with Amazon Alexa or Google assistant.
Removal of Sensor (optional)
There may be circumstances where the sensor cannot be installed because of
molding/door limitations or is not aesthetically desirable. The sensor wired to the lock is
removable by carefully pulling its connector from the circuit board. If removed, some
features and functionality will not be available, such as real-time condition status.
TIP: Lockly offers both brown and black sensor covers that can be ordered through
our customer care hot line: [phone] or by email: [email protected].
IMPORTANT: Gap must be less than 3/4” when installed.
When installed on door, the distance between the wired sensor and
sensor magnet must be less than 3/4” in order for the sensor to work.
If door frame is higher than door, add included foam pads to level
parts (P) and (Q) with each other as much as possible.
PREPARING DOOR SENSORS FOR INSTALLATION
Step 4
Do not mount (install) door sensors yet. You will install in step 7.

Right
or
Left
When installing the door sensors, make sure the
arrow on the wired sensor (P) aligns to the arrow of
the sensor magnet (Q) as close as possible.
The sensors need to be as close
to level as possible. If needed,
use the adhesive foam pad(s)
to adjust the height of the wired
sensor.
Sensors can be positioned on either left
or right side (see page 10).
2-3/4" (70mm)
2-3/8" (60mm)
3/4" (20mm)
Foam pad
(P) (Q)
9
PREPARING DOOR SENSORS FOR INSTALLATION
Step 4 continued

The interior assembly comes with the
pre-installed wired door sensor setup for a
right swing doors with 2 ¾" (70mm) backset*.
Trim excess part (P) for doors with 2 ⅜"
(60mm) backset as shown below.
For left swing doors, re-route the door
sensor wire through the side channel.
Pull the foam pad then re-insert to secure
the wire. Discard the excess part (e) for
doors with 2 ⅜" (60mm) backset as
shown below:
*Backset = distance of the door edge to the center of the cross-bore door hole.
DO NOT INSTALL THE SENSORS YET
Pull foam pad Insert form pad
PREPARING DOOR SENSORS FOR INSTALLATION
3
2
1
(P)
10
Step 4 continued
Trim excess here for
2 ⅜" (60mm) backset*

NOTE: If you need to discon-
nect the cable, make sure
to press the snap tab to
release the plug before
carefully pulling it out. Do
not force, as this may result
in damaging the lock.
Plug the larger cable coming through mounting plate (D) into the interior assembly (G) as
shown. Tuck cable under eyelet hooks and route to the right on interior assembly (G).
INSTALLING THE INTERIOR ASSEMBLY (G)
11
Step 5
Connect to screw tightly by
hand as shown. Plug into ,
match red side of plug with red on
socket - insert tightly.
Do not touch pins inside*
Call our Customer Care Hotline
[phone], for help if the
pins are not centered or bent.
A B
XY
YX
AB

RESET PROGRAM
Before placing the interior
assembly onto the mount-
ing plate, ensure the
thumb turn is vertical.
Place the interior assembly
against the mounting plate
and make sure the torque
blade is inserted to the thumb
turn shaft.
Secure the interior assembly
to mount platedoor with
2 screws.
Torque Blade Thumb turn shaft
RESET PROGRAM
H
2X
H
INSTALLING THE INTERIOR ASSEMBLY (G)
12
Step 5 continued
RESET PROGRAM
Align torque blade with thumb
turn shaft, make sure both are in
the vertical position.

13
INSTALLING BATTERIES
Step 6
1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 3
batteries only (hold on inserting the 4th) in bottom row (note correct -/+ polarity).
2: Press and HOLD the program button, continue to hold and install the 4th battery. The lock will
automatically start self-check (release program button once check starts). The self-check process
determines right or left swinging door and is very important to ensure correct installation.
IMPORTANT: if lock is not properly installed it will open and close repeatedly (refer to next page #3).
PRESS
& HOLD
5 6 7 8
123
4
IMPORTANT
Install batteries 5-8 only after
self-check is complete

14
INSTALLING BATTERIES
Step 6
3: Once self-check completes ensure the lock operates smoothly by manually locking and
unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate
smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the
deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt
was extended.
4: Swipe your hand across the touch screen keypad,
the lock should close (lock). If deadbolt bounces
back or unlocks automatically it means something is
not installed correctly. Go back and repeat step 2,
same as above.
5. Once self-check is complete, install remaining 4
batteries and battery cover (I), secure with screw on
top (do not over tighten).

LOCK SENSOR (P)
Install on the interior side only. If necessary, trim tab from sensor (P) for doors with 2-3/8"
(60mm) backset. Clean surface of door and doorframe, remove film from adhesive,
attach and secure close to door edge as shown.
2-3/4" ( 70mm)
2-3/8" ( 60mm)
(P)
15
INSTALLING THE DOORS SENSOR
Step 7
Make sure you have prepared the door sensors for installation, see step 4

NOTE: When properly installed, the Lockly logo blinks red when door opens and closes.
DOOR FRAME SENSOR (Q)
Manually retract deadbolt and close door. Dry fit sensor (Q) to door frame and check
for alignment. If needed, raise the height of the sensor to be more level with sensor (P)
by adding 1 or 2 of the included adhesive foam pads. Once satisfied both sensors are
as level as possible, remove film from adhesive and install with arrows aligned to each
other with less than a 3/4" gap between each sensor.
16
INSTALLING THE DOORS SENSOR
Step 7
(Q)

Use the supplied door strike or use your existing as long as deadbolt operates smoothly
without binding or catching.
IMPORTANT: because doors and frames vary in design it may be necessary to
make slight adjustments to your strike plate and/or dust box in order to ensure
smooth deadbolt operation. This is very important. If the deadbolt is binding or
catching in any way the lock will sound an alarm (rapid beeping) indicating it
cannot close due to misalignment and/or excessive rubbing or binding.
17
INSTALLING STRIKE PLATE
Step 8
L
K(2X) N

18
To enable video doorbell, live monitoring and voice control with Google Assistant or
Amazon Alexa, you will need to setup the included Vision Connect WI-Fi hub and pair it
with the Lockly Vision deadbolt smart lock + video doorbell.
IMPORTANT: Vision Connect stores recorded video on the included TF card. Although
the TF card is discrete, it is recommended to locate it in a discrete or secure area to
protect your privacy and video recordings.
PAIRING VISION CONNECT WITH LOCK
LED status lights
Antenna
VISION CONNECT OVERVIEW
LAN cable
Power adapter
TF card
Reset
Step 9

LOCKLY APP & UNIQUE ACTIVATION CODE
Before connecting Vision Connect Hub download the Lockly app on your smartphone.
It’s required to finish setup and to set (pair) the connection between hub and lock.
Scan, visit app store, or go to Lockly.com/app
IMPORTANT: Without the QR code you will not be able to reset your lock
19
Step 9 continued
Additionally, you'll need the Activation
Card with unique pre-paired QR code to
your lock. The card is located in the
packaging that your lock came in. This
QR code can also be found at the
bottom of Vision Connect Hub. Please
keep it in a safe place—this QR code is
required to complete the setup and will
be required if you lose your smartphone
or access code.
LOCKLY.COM | HOTLINE: [phone] | EMAIL: [email protected]OM
AUTHENTIC LOCKLY PRODUCT | DESIGNED IN USA | CARD IS PRINTED WITH A SPECIFIC PATTERN
SECURE ADDITIONAL DOORS AT A DISCOUNT:HTTP://WWW.LOCKLY.COM/MORE
ACC20200402
LOCK SERIAL
ACTIVATION CODE
PGDxxxxxxxxxx
xxxxxxxx SCAN & SAVE