Lockly LUX Compact User manual

MORTISE EDITION
INSTALLATION
GUIDE
LUX COMPACT

Go to Lockly.com/installation to watch a video
version of this installation guide.
Download the BILT app from the App Store or on
Google Play for step-by-step interactive 3-D
walk-through installation instructions.
OR

Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to install and get
your Lockly Lux Compact up and running. Installation generally takes
less than 30 minutes. If you have any questions please reference our
online support at: Lockly.com/support or call [phone] for help.

3
Preparation
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
Pliers
（Optional）
Screwdriver with drill bits
Drilling is not required to install the lock, and is optional. However if you are installing
your lock on a brand new door, a drill is required if there are no holes prepared for
lock installation.

Interior Panel
for Part N
Use provided drilling templates to prepare door for installation.
You would need professional door drilling tools.
2-3/8"(60mm)
Exterior Panel
for Part B
1/2"
12mm
4-1/8"
105mm
2-1/8"
54mm
4
Preparation
1-3/8" - 2"
(35mm - 50mm)
Measure and confirm your door is
between
1-3/8" - 2" ( 35mm - 50mm).
Measure and confirm the hole in the
door is
2-1/8" (54mm).
Measure and confirm that the backset
is between 2-3/8" (60mm).
Measure and confirm that hole in the
door edge is 1/2" (12mm).
1
2
3
4
IMPORTANT NOTICE
*You are not required to drill an extra hole in
y our door. We have provided double-sided
adhesive tape for you to help stabilize the lock
during installation. Only drill a hole if you wish to
have added stability. Please refer to the provided
template for drilling if needed. Use goggles to
protect your eyes if you need to drill door holes.
Measure and confirm that distance
between front door holes is
4-1/8" (105mm).
5
*Optional
*Optional

5
Step 1 ADJUSTING LOCKSET TO YOUR DOOR ORIENTATION
There are 4 common door-opening directions, the lockset ships default for is for
RIGHT IN-SWING Doors. You may skip this step if you are sure your door is a Right
In-Swing Door. Otherwise, see the illustrations below to confirm your door opening
direction and change your latch throw orientation if needed.
LEFT IN-SWING DOOR
LEFT OUT-SWING DOOR Make sure the latch throw is
correctly oriented as shown
to fit your left out-swing door.
Make sure the latch throw is
correctly oriented as shown
to fit your left in-swing door.

RIGHT OUT-SWING DOOR Make sure the latch throw is
correctly oriented as shown
to fit your right out-swing door.
RIGHT IN-SWING DOOR Make sure the latch throw is
correctly oriented as shown
to fit your right in-swing door.
6
Step 1 continued
ADJUSTING LOCKSET TO YOUR DOOR ORIENTATION

Move the metal barrier upwards.
Hold the moving lip aligned to latch
and twist downwards to 180°.
HOW TO ADJUST THE LATCH THROW
The Factory setting or the throw is for right in-swing door. You do not need to
change direction if you have a right in-swing door. Here is here is how to change
the latch throw direction.
7
Step 1 continued
ADJUSTING LOCKSET TO YOUR DOOR ORIENTATION
1
2
3
4
Push the latch throw inwards
and position the moving lip
aligned with the latch inside
the case.
Release the metal barrier to
fully extend the latch.

When installing the lockset, ensure
the latch is at the top position and
deadbolt is at the bottom.
8
Step 2 INSTALLING THE LOCKSET (PART F)
G
G
F
1
2
Use provide screws Gto secure
the lockset position.

9
Step 3 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
R
The lock ships set for right swing doors. Skip STEP 3 if your door is a right swing door.
See steps below to change door handle orientation for a left swing door.
Determine right swing or left swing door
While facing the door from the inside, if hinges are on the right side you have the right swinging
door. If hinges on the left side you have a left swinging door.
Changing the Exterior Handle Orientation
(Right handle)
12 3
Insert key and rotate lock
face so that the two white
dots align as shown.
Use the provided pin insert R
to push the metal pin located
at the 3 o’clock of the the base
handle, then the other pin at
9 o’clock position. Remove the
handle once the pins are
compressed.
Rotate the handle 180oto the
other side of the lock.
Using your fingers, press the
two pins located on the left
and right side of the the lock
to insert the handle back onto
the lock.

10
Step 3 continued
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Confirm that your installation was
complete by checking if the pins
are flush against the handle, and
has popped out. Adjust the handle
accordingly to make sure the pins
are fully decompressed and sits
flush against the surface.
Check that your handle works
smoothly by giving it a turn up
and down.
Twist key back to horizontal position. The key can
be taken out once it goes back to the horizontal
position.
45
6

Step 3 continued
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
11
7
8
9
Insert the removed screw
from point “R” screw tightly
to point “L”.
Use a flathead screwdriver
to press the middle marker
and move to point “L”.
Remove the screw position
on point “R”

Step 3 continued
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
12
Remove the screw by turning counter
clockwise and rotate the handle 180°
in the direction of the arrow as shown.
Make sure the screw hole is aligned
with the marker as illustrated.
Changing the Interior Handle Orientation
Securely screw clockwise as shown
to complete your handle orientation
change.
12

Step 4 PREPARING LOCK FOR INSTALLATION
13
23
If you drilled a hole in Preparation, use Slotted Barrel Extension Uand securely tighten with a flat head
screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave
this pole removed.
1
Insert locking pin D
in to the hole as
shown above.
4Peel paper layer OFF the
Adhesive tape and
prepare for installation.
D
Install Spindle Cwith
the holes side into the
base of the lock and
align the holes locate
in the 3 o’clock and
9 o’clock position.
Carefully bend the end
of the locking pin D with
a needle nose pliers.
Failure to bend the locking
pin and turn the handle freely
without obstruction will result
to malfunction.

14
Step 5 INSTALLING THE LOCK (EXTERIOR)
1
2
3
Exterior
Install the exterior lock as shown to the
left by aligning the lock straight and
passing the cable and attached rods
through the lockset.
Pass the Spindle Cthrough the center
of the lockset, and the round rods
through the sides in their respective
holes. The cable should run underneath
the lockset.
Align the lock straight and press hard
(if you use the Adhesive tape in step
4.4) to secure the top of the lock.

Step 6 INSTALLING THE LOCK (INTERIOR)
15
Positioning rods slide
through these holes.
Interior Mounting Plate LK will go
against the interior side of your door.
Remove the paper layer off of the
Adhesive Tape and align the positioning
rods on the bottom of the plate to the
corresponding left and right holes.
Install the side with the black plastic
seal against the door.
Mounting Plate LK
1
2
Interior
V
Insert Positioning Rods Vinto the holes
to the left and right of the Spindle C.
The holes are located at the 3 o’clock
and 9 o’clock positions.

Step 6 continued
INSTALLING THE LOCK (INTERIOR)
16
PM5 x 25mm
PM5 x 35mm
M1
M2
LK
*Secure top with M1 or M2
Secure O
O
2x
Pull the cable from the lock exterior
through the rectangular hole
underneath the positioning rods
and spindle.
Remove the position rods Vand
replace them with screws O
Tighten clockwise until the mounting
plate is secure.
* If you have drilled a hole on the
top in Preparation, please secure
the hole with screw M1 or M2
depending on your door thickness.
Skip this if no hole was drilled in
Preparation.
3
4

Step 6 continued
INSTALLING THE LOCK (INTERIOR)
17
5
6
X
Y
Plug Xcable that is coming through the door into the lock
interior Y. Match red side of the plug with red on socket -
insert tightly.
Make sure the cable is away and
not tangling with the square rod C
NOTE: If you need to disconnect the cable,
make sure to press the snap tab to release
the plug before carefully pulling it out. Do not
force, as this may result in damaging the lock.
Align the square rod to the lock interior and attach
the Interior lock to the Interior mounting plate.
While you are doing so, gently push some of the excess
cable through the rectangular hole into the door.
Place the remaining cable against
the interior side of the lock interior
so the lock interior sits securely
onto the mounting plate.

18
Step 6 continued
INSTALLING THE LOCK (INTERIOR)
+
+
-
-
P (3X)
Once the lock interior is flush against
the mounting plate, secure the lock
to the plate by screwing clockwise
using provided screws P.
Insert 4 AA batteries into the lock by
aligning the positive +and negative
- orientation markings on the batteries
to the battery chamber.
Secure the battery cover by sliding the
cover over the lock and turning the screw
clockwise on top until tight.
7
8

Step 7 INSTALLING THE DOOR STRIKE
19
INSTALLING THE DOOR STRIKE
Screw G
Screw G
Strike Plate H
Dust Box I
Install the strike box as shown below. Open the door frame, install box, then the strike plate and
fix it with screws.
After the installation is completed, check if the lock is working smoothly. From the INDOOR, while
the door is open, lift the handle to check if the lock opened and closed smoothly and whether the
deadbolt and latch are fully extended to the strike. Re-adjust the installation location accordingly
if the deadbolt and latch are not aligned to the strike.