Lockly DUO User manual

INTERCONNECTED EDITION
INSTALLATION
GUIDE
DUO™

Go to Lockly.com/installation to watch a video version
of this installation guide.

Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly Duo
™
up and running.
Installation generally takes less than 30 minutes. If
you have any questions please reference our online
support at: Lockly.com/support or call [phone]
for help.

3
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
Preparation
Pliers
Optional
Screwdriver with drill bits
Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a
drill is required if there are no holes prepared for lock installation. Use provided template to bore
holes on door.

4
Preparation
Measure and confirm your door is
between 1-3/8" - 2" ( 35mm - 50mm).
Measure and confirm the hole in the
door is 2-1/8" (54mm).
Measure and confirm that the
backset is between 2-3/8" (60mm)
to 2-3/4" (70mm).
Measure and confirm that hole in
the door edge is 1" (25mm).
Remove existing door hardware, latch or deadbolts before installing the new lock.
Use provided template to bore new holes if needed.
1
2
3
4
Measure and confirm that distance
between front door holes is
4"(101.6mm) or 5.5"(139.7mm)
5
1- 3/8"—2"
(35mm—50mm)
2-3/8"(60mm)
or
2-3/4"(70mm)
2-1/8"
54mm
54mm
1"
25mm
4"(101.6mm)
or
5.5"(139.7mm)
2-1/8"
1"
25mm
*Optional
IMPORTANT NOTICE
* Use goggles to protect your eyes if you need to drill door holes.

5
INSTALLING THE LOCKSET
Step 1
1
2 ⅜"(60mm) 2 ¾"(70mm)
(a)
II. Hold the metal plate (c) and
twist the deadbolt body (d)
clockwise till it snaps to 2-3/8"
III. To return to default status,while
the deadbolt (b) is extended, hold
the metal plate (c) and twist the
dead bolt body (d) counter-clock-
wise till it snaps to 2-3/4"
I. Push the crank (a) to extend
the deadbolt (b)
Deadbolt Adjustment
Latchbolt Adjustment
b
cd
dc
a
Push the shaft (a) to adjust
the lockset to 2-3/8"(60mm)
or 2-3/4"(70mm).
2-3/8"
(60mm)
2-3/4"
(70mm)
G
G
G
G
Measure the distance between center of front door hole to the edge of your door hole to
determine the backset. Adjust latchbolt Fand deadbolt Jaccording to the backset
of your door.

6
INSTALLING THE LOCKSET
Step 1 continued
After adjusting the latchbolt F, determine the orientation of the latchbolt.
Determine the orientation of latchbolt. Facing the door exterior, install the
latchbolt according to the opening direction of your door.
2
J
K
K
F
Install deadbolt J (top) and latchbolt F(bottom) to door and secure with screws Kand G.
Retract deadbolt and make sure bore hole is horizontally positioned.
Optional: Stainless steel mortise slot cover, 4" or 5.5" Face Plates available. To purchase,
please call our Customer Service hotline [phone] or email [email protected]
PGA018
PGA019 PGA019S
For mortise slot
5.5” 4”
3
LEFT OUT-SWING DOOR
LEFT IN-SWING DOOR
RIGHT OUT-SWING DOOR
RIGHT IN-SWING DOOR
Inside
Inside
Outside
Outside
Inside
Outside
Inside
Outside

7
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below
if you are unsure of you door orientation.
Changing the Exterior Handle Orientation
(Right handle)
Insert key and rotate lock
face so that the two white
dots align as shown.
12
R
Hinge
Side
RIGHT IN-SWING DOOR
LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR
LEFT IN-SWING DOOR
Use the provided pin insert Rto push the metal
pin located at the 3 o’clock of the the base handle,
then the other pin at 9 o’clock position. Remove the
handle once the pins are compressed.
INTERIOR
EXTERIOR
No need to change door handle
orientation. Skip Step 2.
LEFT-IN SWING and RIGHT OUT-SWING DOORS
require changing the door handle orientation.
Contnue to follow Step 2 to change exterior
and interior door handle orientation.

8
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2 continued
Check that your handle works
smoothly by giving it a turn up
and down.
Twist key back to horizontal position. The
key can be taken out once it goes back
to the horizontal position.
34
56
Rotate the handle 180° to the other side of the
lock.
Using your fingers, press the two pins located on
the left and right side of the the lock to insert
the handle back onto the lock.
Confirm that your installation was complete
by checking if the pins are flush against
the handle, and has popped out. Adjust
the handle accordingly to make sure the
pins are fully decompressed and sits flush
against the surface.

CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2 continued
Remove the handle retaining screw and
detach the handle. Rotate it to 180° then
return as shown.
Changing the Interior Handle Orientation
Insert the handle retaining screw and
tighten using a screw driver.
12
9
At the back of the exterior panel,
remove the screw on point "R".
78
Align the screw hole on point "L" then
insert the removed screw and tighten.

10
PREPARING LOCK FOR INSTALLATION
1
Install Spindle Cwith
the holes side into the
base of the lock and
align the holes locate
in the 3 o’clock and 9
o’clock position.
4
Peel paper layer OFF
the Adhesive tape and
prepare for installation.
Carefully prepare the lock and ensure the required parts ( C, D, E, U) have been properly
attached before installing to door.
Step 3
2
D
3
Insert locking pin D
in to the hole as
shown above.
Carefully bend the end of
the locking pin D with a
needle nose pliers.
Failure to bend the locking
pin and turn the handle
freely without obstruction
will result to malfunction.

11
PREPARING LOCK FOR INSTALLATION
5
6
Attach exterior cover plate Eto exterior assembly B. Use screw Ito secure the cover
plate.
IE1 or E2
B
4" use cover plate 5.5" use cover plate
Select or exterior cover plate according to front door hole distance.
E1 E2
Step 3 continued
E1 E2

12
INSTALLING EXTERIOR SIDE OF LOCK
Step 4
Check lock alignment and
ensure that it is sitting flat and
aligned straight.
Pass the spindle Cthrough the
center of the latchbolt, and the
round rods through the sides in
their respective holes. The cable
should run underneath the lockset.
1
23
Exterior
Exterior
While aligning the lock straight up-and-down, pass
the wiring cable under the latchbolt Fthen ensure
the rod on cover plate Epasses through the hole
on the lower part of the deadbolt Jbody as shown.
C

13
INSTALLING INTERIOR SIDE OF LOCK
Step 5
Select interior cover plate or according to door hole distance and install on to door.
V
U2
or
U1
1
Ensure the rods on interior cover plate U1 or U2 is inserted on the holes of the deadbolt.
and the cable and spindle Cpassed through part U . Insert positioning tool Vthrough
the spindle to hold the cover plate in place.
2
4” use cover plate
4” (101.6 mm)
5.5” use cover plate
U1 U2
5.5” (139.7 mm)
U2
U1

14
Step 5 continued
Secure interior cover plate Uwith screws O , then remove the positioning tool V.
Check and ensure the spindle is at the center after removing V
3
Hole for screw for 5.5"
O
Hole for screw for 4"
O
INSTALLING INTERIOR SIDE OF LOCK
Check and ensure the
spindle is at the center
after removing V .
V
O

15
Step 5 continued
Select the side of the interconnection gear Paccording to door handle orientation Left
or Right . Insert torque blade AD to plate according the distance between the latchbolt
and deadbolt .
Select the correct side of the interconnection gear.
Insert AD for 4"
Insert AD for 5.5"
AB
P
4
INSTALLING INTERIOR SIDE OF LOCK
This side should be
facing infront of you.
This side should be
facing infront of you.
For right swing door For left swing door
IMPORTANT:
Torque Blade for Right swing door must be
installed on L side.
Torque Blade for Left swing door must be
installed on R side
You may strike AB with pliers
to insert it to 4' or 5.5" hole.

16
Step 5 continued
Install plate Ponto door. Ensure the
torque blade AD is inserted horizontally
to the deadbolt. The spindle must pass
through the plate. Secure the plate with
screws M.
56
Mounting Plate LK
On the interior side of the door install
mounting plate LK . Be sure to remove
protective cover on adhesive tape before
mounting. Attach LK to the intercon-
nection plate, make sure cable passes
through the plate and the spindle is
centered in the mounting plate.
INSTALLING INTERIOR SIDE OF LOCK
LK
AD
MX3

17
Step 6 PREPARING DOOR SENSOR FOR INSTALLATION
Part AA - Wired Sensor Part AB - Sensor Magnet
IMPORTANT: Gap must be less than 3/4” when installed.
Do not mount (install) door sensors yet. You will install in step 9.
About door sensors
Door sensors provide real-time door condition status, such as the ability to verify if the door is securely
closed. It also sends push notifications to your phone whenever your door opens and enables voice
control with Amazon Alexa or Hey Google.
Lockly Duo™comes with a pre-wired door sensors consisting of two parts:
Removal of Sensor (optional)
There may be circumstances where the sensor cannot be installed because of molding/door
limitations or is not aesthetically desirable. The sensor wired to the lock is removable by carefully
pulling its connector from the circuit board. If removed, some features and functionality will not
be available, such as real-time condition status.
When installed on door, the distance between the wired sensor and sensor
magnet must be less than 3/4” in order for the sensor to work. If door frame
is higher than door, add included foam pads to level parts AA and AB with
each other as much as possible.
Lockly door sensors comes in Grey (PGA061) and Matte Black (PGA062) that can be
ordered through our customer hotline: [phone] or by email: [email protected].
TIP：

18
Step 6 continued
PREPARING DOOR SENSORS FOR INSTALLATION
OR
If needed add Foam Pads to level
AA & AB as much as possible.
2-3/4"
(70mm)
2-3/8"
(60mm)
< 3/4"
(< 20mm)
EVA
LEFT RIGHT
When you are installing the door sensors, make
sure the arrow of the wired sensor AA is placed
next to the arrow of the sensor magnet AB as
close as possible.
IMPORTANT: Do not install the sensor
close to the strike plate H.
H
H
AA
AB
AB
AA

19
PREPARING DOOR SENSORS FOR INSTALLATION
Step 6 continued
1 2
DO NOT INSTALL THE SENSORS YET
The interior assembly comes with the pre-in stalled
wired door sensor setup for a right swing doors with
2-3/4" (70mm) backset*.
Trim excess part efor doors with 2-3/8" (60mm)
backset as shown below.
For left swing doors, re-route the door sensor
wire through the side channel. Trim excess
part e for doors with 2 ⅜" (60mm) backset
as shown below.
*Backset - measure the distance of the door edge to the center of the door hole.
(AA)
e
Trim excess here for
2 ⅜"
(60mm) backset*.
Make sure you install the Door Sensor indoors on a clean and dry surface. Gently wipe the surface
of your door and door frame where you wish to install the Door Sensor and make sure it’s dry
before installing.
Keep the Door Sensor away from direct sunlight, high heat locations and large metal objects that
may interfere with wireless signals.