Lockwood ASSA ABLOY Induro User manual

Cylinder Key & Turn KnobCylinder Double Key
Interior Furniture
(Aria Furniture shown)
Exterior Furniture
(Aria Furniture shown)
2-Point Lock
(30mm Backset Shown)
or
92mm Drive Bar (Spindle)
• Drill
• 3.2mm Drill Bit
• 10.0mm Drill Bit
• 20.0mm Drill Bit
• Phillips Screwdriver #2
• Square Screwdriver #1
8g x 7.5 Screws
M4 Furniture fixing screws
M5 Cylinder fixing screw
Screw Selection:
Screw Stile Width
M4 x 49mm 38 - 43mm
M4 x 55mm 43 - 49mm
M4 x 60mm 46 - 55mm
M4 x 65mm 55 - 58mm
Latch Wear Pad2mm Latch Packer
Tools Required:Application: Provides secure deadlocking for aluminium hinged
doors. Palladium Xtra furniture available with daylatch snib.
Pack Contents:
InduroTM Mortice Lock
Palladium Furniture, 2-Point
Installation Instructions

Ø 3.2
56 63
198
60
85
103
122
184
Ø 10
Ø 20
1000mm To
The Bottom Of
The Door
SIDE VIEW OF STILE
TOP VIEW OF STILE
FRONT VIEW OF STILE
R 10
21
R 3
Ø 3.2
Ø 10
30mm backset routing is 28mm from face
40mm backset routing is 38mm from face
50mm backset routing is 48mm from face
1. Door Preparation
Route the door as shown in the routing diagram.
Note: For Palladium Xtra Furniture, see separate instructions.

Short Throw (13mm)
Long Throw
(24mm)
2. Setting Deadbolt Projection
• Before fixing the lock into the stile, select the correct deadbolt throw.
• To restrict the throw to 13mm select S
• To restrict the throw to 24mm select L
• Ensure the arrow is pointing to the desired throw application.
4. Fixing Furniture and Cylinder
• Insert the drive bar (spindle) through the square
drive hole in the lock
• Place the furniture onto the drive bar. For security,
ensure the interior handle is on the inside of the
house
• Place the cylinder through the cylinder hole
• Fix cylinder using the supplied M5 cylinder fixing
screw as supplied
• Fix together the furniture using the two M4
furniture fixing screws. See screw selection chart
to determine correct screw length
Note: If fixing Palladium Xtra Furniture with
daylatch snib, refer to separate Palladium Xtra
Furniture instructions enclosed.
3. Fixing Lock
• Place the lock assembly into the stile
• Fix the lock onto the stile using the two 8g x 7.5 screws
Note: When lock has 13mm projection selected the key must be rotated once
deadlock. When lock has 24mm projection selected the key must be rotated twice
to deadlock.

M4 Latch Screw
Latch Wear Pad
Latch
2mm Latch
Packer
Troubleshooting
Do I need to tap holes? No. All screws are self tapping.
The furniture screws do not
tighten
Ensure the screws line up with the screw
boss on the exterior handle.
Do I have to use the
supplied screws?
For best performance, it is
recommended that only the supplied
screws are used.
The key function does not
operate
Ensure the motion of the latch is not
restricted.
Can not achieve 24mm
deadbolt throw
Ensure locks deadlock is set to ‘L’. Turn key
twice.
Deadbolt
Latch Handle
Turn key
to throw
deadbolt
5. Latch Reversal
• Undo the M4 latch screw
• Reverse the latch as desired
• Refasten the M4 latch screw to secure the latch
• Insert the latch wear pad
Note: 2mm Latch Packer is provided to allow for latch
projection adjustment. An additional 2mm packer is
available for purchase.
6. Lock Operation
Deadlocking Operation
• Pull the door shut. The door will self-latch
• Turn the key towards the edge of the door to deadlock
Note: For 13mm, turn the key once only
For 24mm, turn the key twice
• The door is now secure from exterior and interior
Opening Operation
• Turn the key away from the door edge to deactivate the deadlock
Note: For short throw, turn the key once only
For long throw, turn the key twice
• Retract the latch
ASSA ABLOY New Zealand Limited
6 Armstrong Road, Albany, Auckland 0632
[e-mail]
www.assaabloy.co.nz Q50287_1221
ASSA ABLOY Australia Pty Limited
235 Huntingdale Rd, Oakleigh, VIC 3166
ABN 90 086 451 907 ©2019
1300 LOCK UP
www.assaabloy.com.au