Logitech Z906 User's Guide Assembly Instructions

Z906 5.1 SURROUND SOUND
SPEAKER SYSTEM
SYSTÈME DE HAUT-PARLEURS
Z906 AVEC SON SURROUND 5.1
Complete Setup Guide
Guide d’installation complet

CONTENTS
English . . . . . . . . . . . . . . . . .3
Français . . . . . . . . . . . . . . . .9
Español . . . . . . . . . . . . . . . . 15
Português . . . . . . . . . . . . . . 21

English 3
KNOW YOUR PRODUCT
6-channel direct
(PC sound card)
DB-15 pin
connector
Rear left
Rear right
Front left
Front right
Center
Power plug
RCA (stereo)
Digital optical Digital coaxial
REAR LEFT
REAR RIGHT
FRONTLEFT
FRONT RIGHT
CENTER
SPEAKERS
CONSOLE
INPUTS
5
1
2
43
Subwoofer back panel:

English 4
INPUT
2
1
3
4
5
AUX
INPUT EFFECT LEVELMUTE
3D
4.5
2.1
DECODE
STEREO
Power On/O
Decode indicator
Input indicator
Volume/Level adjust
Eect select*
Volume/
Levelindicator
Speaker indicator
Headphone jack
Auxiliary input
IR remote window
Level select
Mute
INPUT
LEVEL
EFFECT
MUTE
Power On/O
Volume/Level down
Three AAA batteries
Mute
Level select
Volume/Level up
Eect select*
Battery door
Input select
KNOW YOUR PRODUCT
Control console:
Remote control:
*Eect select
• Stereo 3D – Provides a 3D surround sound eect through all speakers.
• Stereo 4.1 - Plays stereo through both front and both rear satellites, plus the subwoofer.
• Stereo 2.1 – Plays stereo through both the front satellites and the subwoofer.

English 5
CONNECT THE SPEAKERS
Make sure that speakers, control console, and audio source are all POWERED OFF before you begin system setup.
1. Connect the speaker cables:
Connect each satellite to its corresponding plug (red or black) on the subwoofer back panel. Push the tab
onthe spring clip, insert the wire into the connector, and release the tab.
2. Connect the audio source cable:
Turn o the speakers. Connect your audio source (e.g., TV, DVD, computer) to the appropriate input jack
onyour subwoofer.
• For computer sound cards, use the 6-channel input 1 (cable included).
• To connect to analog outputs, use the stereo RCA input 2 or the auxiliary input on the side of
thecontrolconsole (cables not included).
• To connect to digital outputs, use the two optical inputs and the coaxial input 3, 4, 5 (cables not included).
1 2
REAR LEFT
REAR RIGH T
FRONT LEFT
FRONT RIGHT
CENTER
SPEAKERS
CONSOLE
543
CONSOLE
INPUTS
5
1
2
43
1
2
3 4
5
ADJUST THE VOLUME
1. Power on the speakers. Set volume to the nine o’clock position to test.
Adjust the volume by turning the control knob to the left or right.
2. You can also adjust the volume on the remote control by pressing the +/- buttons.
INPUT
LEVEL
EFFECT
MUTE
INPUT
2
1
3
4
5
AUX
INPUT EFFECT LEVELMUTE
3D
4.5
2.1
DECODE
STEREO
1 2

English 6
SPEAKER PLACEMENT
Satellite speakers:
Place the two front satellite speakers on either side of
yourcomputer monitor or television, about the same
distance from each other as they are from your listening
position (e.g. the couch). Angle them to face you.
Placethetwo rear speakers behind you and about the same
distance apart as the front speakers. You may want to
mount these speakers on the wall (see Wall mounting*).
Center satellite speaker:
Place your center satellite speaker on your desk, or in front
ofyour monitor or television; you may also wall-mount it.
Subwoofer:
You can place the subwoofer anywhere in relation to
theother speakers. To get the strongest bass, place
yoursubwoofer near a wall or corner, or under a desk.
Makesure that nothing is closer than 16 cm to the
driver or the bass port because it will aect your sound.
It’salsoimportant to have adequate ventilation around
thesubwoofer.
Control console:
Place the control console where it’s easy to reach. And make
sure the IR window is in plain view so the remote control can
communicate with it.
*Wall mounting: You can mount your satellite speakers with
the appropriate hardware (not included). When attaching
a satellite speaker to a wall mount, make sure not to
overtighten the mounting screw. Doing so may damage
thescrew threads inside the speaker’s mounting lug.
Subwoofer
Couch
Subwoofer

English 7
TEST THE SYSTEM
To test if you have correctly set up your speakers, press and
hold the INPUT button on the remote control or control
console for 5 seconds to put your system into test mode.
In test mode, the system cycles through each speaker,
playing an audible test signal. The test signal comes
from only one speaker at a time, in 5-second intervals,
inthefollowing order: left front, center, right front, right rear,
left rear, and subwoofer.
As a channel is tested, its corresponding LED lights up on
the front panel of the control console. The test signal cycles
through each speaker one time and stops. To re-enter test
mode, press and hold the INPUT button on the remote
orcontrol console for 5 seconds.
INPUT
LEVEL
EFFECT
MUTE
INPUT
2
1
3
4
5
AUX
INPUT EFFECT LEVELMUTE
3D
4.5
2.1
DO LBY
STEREO
SELECT AUDIO INPUT
Use the remote control or the control console to select
aninput source. Pressing the INPUT button cycles
through the various audio input sources. The numbers
ofinputs showing on the control console correspond to
theconnections number on the back of the subwoofer.
Ifyou’re using a digital connection, follow the instructions on
your audio source to make sure you’re getting digital audio
output. For digital content, the control console automatically
detects and displays the digital stream as long as the device
is connected to a digital input. For example, if you have
selected the DTS Digital Sound or Dolby Digital 5.1 stream for
a DVD you want to watch, it will be detected automatically
when you choose the applicable input.

English 8
LEVEL SELECTION
Use the level select button on the remote control or
the control console to adjust the volume of the system.
Dierentlevel adjustment mode are applied under
dierenteects.
1. Stereo 3D - Adjust the volume of the whole system
(5satellites + 1 subwoofer), the subwoofer, rear satellites,
orthe center satellite.
2. Stereo 4.1 - Adjust the volume of the 4 satellites and
1subwoofer, the subwoofer, or the rear satellites.
3. Stereo 2.1 - Adjust the volume of the 2 front satellites
andthe subwoofer or the subwoofer.
4. No Eect - Level select options are same as stereo 3D.
INPUT
2
1
3
4
5
AUX
INPUT EFFECT LEVELMUTE
3D
4.5
2.1
DECODE
STEREO
Eect select
control
Level select
button
INPUT
LEVEL
EFFECT
MUTE
Eect select button
Level select button
EFFECT SELECTION
When playing stereo audio, you can use the eect select button
on the remote control or the control console to choose the type
ofsound you want to hear.
1. Stereo 3D – Provides a 3D surround sound eect through
allspeakers.
2. Stereo 4.1 – Plays stereo through both front and both rear
satellites, plus the subwoofer.
3. Stereo 2.1 – Plays stereo through both the front satellites
andthe subwoofer.
4. No eect – Plays audio format of your computer’s sound card
without applying any eects. Available for 6 channel input
only and is represented by having no eect LEDs illuminated.
Eect options for analog audio:
1. RCA and auxiliary inputs: select 3D, 4.1, and 2.1 for
yourlistening preference.
2. 6-channel input: select 3D, 4.1, 2.1, or no eect for
yourlistening preference.
You can enjoy DTS Digital Sound or Dolby Digital 5.1 streaming
by making sure that your audio source support these two audio
encoding technologies (please refer toSELECT AUDIO SOURCE).
Whenever you change the input, the last eect you selected
isautomatically restored.
For example, if you select Stereo 3D while listening through Input 2,
the next time you select Input 2 (i.e., the RCA stereoinput), Stereo
3D is automatically selected.