LogTag UTRED30-16 User manual

Version E
www.logtag-recorders.com
Quickstart Guide

What’s Included 3
Battery Installation 4
Downloading LogTag Analyzer 5
Configuring your UTRED30-16 6
Starting your UTRED30-16 7
Downloading Results 8
Quickstart Guide Contents

Page 3
What’s included
Please check you have each of the items shown below before
continuing with setting up your UTRED30-16.
UTRED30-16
USB Cable
2x AAA Battery
(Not included)
ST100X
External Probe
(Not included)
What you also require:

Page 4
Battery Installation
1. You will need a small phillips (cross-shaped) screwdriver to
remove the cover on the back of the UTRED30-16 case.
2. Once you have removed the battery cover, install the 2x AAA
batteries. Take note of the direction each battery must be
installed.
3. Once both batteries are securely installed, replace the battery
cover and secure via the screw you used to open the cover.
The AAA batteries are the main power source for your UTRED30-16.
A USB cable is another power backup source if you wish to power
the unit permanently via the USB socket.
Warning: Please note the UTRED30-16 will not start if AAA
batteries are low and there is no USB power.

Page 5
Downloading LogTag Analyzer
To download the latest LogTag Analyzer, open your browser and
navigate to:
https://logtagrecorders.com/software/LTA3/
1. Fill in the form with your details, then click ‘Go to downloads
page’
2. Click ‘Download Now’ to start the download
3. Click ‘Run’ or ‘Save File’ then double-click the downloaded file to
open Analyzer Setup Wizard
4. Once the Analyzer Setup Wizard is open, follow the on-screen
prompts to install Analyzer onto your computer
5. Click ‘Finish’ to exit the Setup Wizard
Warning: Please ensure no other LogTag software is currently
running on your computer before running the Analyzer software.

Page 6
Configuring your UTRED30-16
Connect your UTRED30-16 to your
computer via the USB cable provided.
The USB socket on the device is
located on the bottom, protected by a
rubber seal.
1. Open LogTag Analyzer
2. Click ‘Configure’ from the ‘LogTag’ menu or click the ‘Wizard’
icon
3. Adjust your logger configuration settings as required.
For more information on configuration settings, please refer to
Configuring the UTRED30-16 in the Product User Guide or press
‘F1’ for help from your keyboard
4. Click ‘Next’ to upload the configuration settings to the logger
5. Click ‘Close’ to exit the configuration page

Page 7
Starting your UTRED30-16
Press and hold the START/
Clear/Stop button.
STARTING will appear along
with READY.
Release the button once
READY disappears.
The UTRED30-16 now records
temperature data.
The Logger will not start if:
• You release the
button before READY
disappears.
• You keep holding the
button for more than 2
seconds after READY
disappears.
• The backup battery is
critically low and the
logger is not connected
to power.
Please ensure you have connected an ST100X external probe to
your device before starting.
Please ensure you have connected an ST100X external probe to
your device be
f
ore startin
g.

Page 8
Downloading Results
Alternatively, you can follow the steps below:
1. Open LogTag Analyzer
2. Click ‘LogTag’ from the ‘Download’ menu or press ‘F4’
3. Click ‘Close’ to exit the download page
Connect your UTRED30-16 to your
computer via the USB cable provided.
The USB socket on the device is
located on the bottom, protected by a
rubber seal.
A new device drive will appear in file explorer with the files
containing the recorded data.
By default, auto-download is enabled in LogTag Analyzer so
when you open the program, data results will be displayed after
connecting your UTRED30-16 to your computer