LogTag Utrel 30-16 User manual

Version A
www.logtagrecorders.com
Quick Start Guide

What’s included 3
Battery Installation 4
Downloading LogTag Analyzer 6
Configuring your UTREL30-16 8
Starting your UTREL30-16 9
Downloading Results 10
Quickstart Guide Contents

Page 3
What’s included
Please check you have each of the items shown below
before continuing with setting up your UTREL30-16.
UTREL30-16 USB Cable
AC Adapter
(Not included)
2x AAA Battery
(Not included)
ST10 External
Probe
(Not included)
Wall mount
(Not included)

Page 4
Battery Installation
1. You will need a small phillips (cross-shaped)
screwdriver to remove the cover on the back of the
UTREL30-16 case.
The AAA batteries are the main power source for your
UTREL30-16.
A USB cable is another power backup source if
you wish to power the unit permanently via the USB
socket.

Page 5
Battery Installation continued...
2. Once you have removed the battery cover, install
the 2x AAA batteries.
Take note of the direction each battery must be
installed.
3. Once both batteries are securely installed, replace
the battery cover and secure via the screw you used
to open the cover.
Warning: Please note the UTREL30-16 will not start if
AAA batteries are low and there is no USB power.

Page 6
Downloading LogTag
Analyzer
Warning: Please ensure no other LogTag software is
currently running on your computer before running the
Analyzer software.
To download the latest LogTag Analyzer, open your
browser and navigate to:
https://logtagrecorders.com/software/LTA3/
1. Click ‘Go to downloads page’ to take you to the
download page.
2. Click ‘Download Now’ to start the download.
3. Click ‘Run’ or ‘Save File’ then double-click the
downloaded file to open the LogTag Analyzer Setup
Wizard.

Page 7
Downloading LogTag
Analyzer continued...
Note: If you already have LogTag Analyzer installed,
please see whether you need to update to the latest
version by clicking ‘Check Internet for updates’ from
the ‘Help’ menu.
4. Follow the on-screen prompts to install LogTag
Analyzer.
5. Click ‘Finish’ to exit the LogTag Analyzer Setup
Wizard.

Page 8
Configuring your
UTREL30-16
Connect your UTREL30-16
to the computer via the USB
port. The USB socket on
the device is located on the
bottom, protected by the cap.
1. Open LogTag Analyzer.
2. Click ‘Configure’ from the ‘LogTag’ menu or click
the ‘Wizard’ icon.
3. Adjust your logger configuration settings as
required. For more information on configuration
settings, please refer to Configuring the UTREL30-16
in the Product User Guide or press ‘F1’ for help from
your keyboard.
4. Click ‘Configure’ to upload the configuration
settings to the logger.
5. Click ‘Close’ to exit the configuration page.

Page 9
Starting your UTREL30-16
Press and hold the START/
CLEAR/STOP button.
STARTING will appear
along with READY.
Release the button once
READY disappears.
The UTRED30-16 now
records temperature data.
The Logger will not start if:
• You release the
button before READY
disappears.
• You keep holding the
button for more than 2
seconds after READY
disappears.
• The backup battery is
critically low and the
logger is not connected to
power.
Please ensure you have connected an ST10 external
probe to your device before starting.
Please ensure
y
ou have connected an
S
T10 external
probe to your device be
f
ore startin
g.

Downloading Results
Alternatively, you can follow the steps below:
1. Open LogTag Analyzer
2. Click ‘LogTag’ from the ‘Download’ menu or press
‘F4’
3. Click ‘Close’ to exit the download page
Connect your UTREL30-16 to
your computer via the USB
cable provided. The USB socket
on the device is located on the
bottom, protected by a rubber
seal.
A new device drive will appear in file explorer with the
files containing the recorded data.
By default, auto-download is enabled in LogTag
Analyzer so when you open the program, data results
will be displayed after connecting your UTREL30-16 to
your computer