Long range T4300A User manual

Long Range LLC. 26 Tannery Street Franklin, NH 03235
T4300A
T4300A-V
T4300 Skeet

Introduction
The T4300A and T4300A-V are simple to use transmitters that can control 2 trap machines with the
push of a button. The T4300A-V has the added ability to launch targets using voice control. Both
transmitters require a 9-volt battery and an antennae.
Press any button to power on the transmitter. Be aware the this rst button press, even though the
device is o󰀨, will re the corresponding trap or traps. The Red Power LED will illuminate to let you know
that the device is on and ready to launch the second target.
The T4300A-V has a microphone included. For best results, clip this microphone to the lapel of vest or
shirt, about 6-9 inches from your mouth.
1
Antenna
Red Power LED
Trap 1 Button
Microphone Jack
Only on the T4300A-V
Green Tx Light
Indicates transmitter is armed
Trap 2 Button
Doubles Button
Throws a True Pair

Button Operation (T4300A & T4300A-V)
Voice Operation (T4300A-V Only)
Press Trap 1 or Trap 2 to re the corresponding trap. The Green TX LED will illuminate to indicate that
a signal is being transmitted and the corresponding trap will re. Press the Doubles Button to re a
True Pair, which will re both traps simultaneously.
Be sure to have the supplied microphone plugged into the Microphone Jack on the top of the T4300A-V
and clipped to the lapel of vest or shirt, about 6-9 inches from your mouth. The T4300A-V can be clipped
to a belt or put in a pocket of a shooting vest.
Once the microphone is plugged into the Microphone Jack, the T4300A-V automatically enters voice
activation mode. To re a single target, press either Trap 1 or Trap 2. This arms the device but does
not re the trap. The Green Tx Light will illuminate to indicate that the device is armed and is waiting
for the voice command. When ready, call “Pull” in a normal tone of voice to re the designated trap. The
trap will re and the Green Tx Light will go out until another button is pressed.
To re both traps simultaneously, press the Doubles button. This arms the device but does not re the
traps. The Green Tx Light will illuminate to indicate that the device is armed and is waiting for the voice
command. When ready, call “Pull” in a normal tone of voice to re both trap 1 and trap 2. The traps will
re and the Green Tx Light will go out until another button is pressed.
Lock On Mode (T4300A-V Only)
Report Mode (T4300A-V Only)
The Lock On Mode is a feature of the T4300A-V and is used in conjunction with voice operation. Lock
On Mode allows Trap 1,Trap 2, or Doubles to be locked in and launched with a verbal command
without pressing a button each time.
To lock in a trap or a true pair, press and hold either Trap 1,Trap 2, or Doubles until the Green Tx LED
ashes (4 seconds). The selected trap(s) are now locked in. When ready, call “Pull” in a normal tone
of voice to re the designated trap(s). The Trap(s) will re and the Green Tx Light will go out. After 4
seconds, the Green Tx Light will begin to ash again and the T4300A-V will be ready to re the same
trap(s). To exit Lock On Mode, press any button.
Report Mode is a feature of the T4300A-V and is used in conjunction with voice operation. Report
Mode allows shooter to call for one trap and have the other trap re on the report of the gun.
To set up Report Mode, press the rst trap that you would like to re (Trap 1 or Trap 2). The Green
Tx LED will illuminate to indicate that the device is armed. Before calling for the target, press the other
trap button. This will be the trap that res on the report of the gun. When you are ready, call “Pull” in a
normal tone of voice to re the rst designated trap. On the sound of the gun, the second trap will re.
2

Skeet Sequence Mode (T4300A-V Only)
The T4300A-V has the Skeet Sequence preloaded. This is designed for solo shooters to go out without
a trapper for practice.
To activate Skeet Sequence Mode, press and hold the Doubles button for 6 seconds until the Green
Tx LED blinks rapidly. Be aware that while holding the Doubles button, the Green Tx LED will begin to
blink after 4 seconds when it enters Lock On Mode. Continue to hold down the Doubles button until
it blinks rapidly.
The T4300A-V is now in Skeet Sequence Mode. When you are ready, call “Pull” in a normal tone of
voice to re a high house. The second call will release a low house and the third call will release a
double. The T4300A-V is now ready for stand 2. Continue through the stands and the T4300A-V will
launch the appropriate trap(s) in the sequence.
At any time during the round, you may press any of the 3 buttons to throw the option bird. After the
option bird is thrown, the unit will resume the skeet sequence.
The T4300A-V will end the sequence after launching the low bird on Station 8. To throw a low 8 option,
press the Low House button and call “pull”.
To exit Skeet Sequence Mode at any time, press and hold the Doubles button until the Green Tx LED
turns o󰀨.
3
Link Mode (Alternative to Using Dip Switches)
1
2
3
4
Set desired Field ID Channel and Trap
Addresses on the transmitter.
Power on desired receiver with all dip switches
set to the open/o󰀨 position. The red Link LED
will blink for 15 Seconds. This indicates that
the receiver is in Link Mode. If a transmitter
has not been linked to the receiver during this
15 seconds, the receiver will revert to the
previous settings.
The red Link Mode light on the receiver will
go solid. The transmitter and receiver are now
linked. Repeat this process to link another
receiver.
Press and hold the trap button that you would
like to assign to the receiver until the green Tx
Light on the transmitter ashes.
Link Mode allows users to wireless link receivers to specic trap buttons. Be sure that the receiver
you wish to link to is in Link Mode. If you are using the T4300A-V, make sure that there is no
microphone attached to the device.
Link LED
Will blink for 15
seconds
Set to open/o󰀨
position
Indicates power
is on
Dip Switches
Power LED
T4300A Field ID Must
Be Set (Channel 1
Shown Here)
R-4300 Dip Switches
Set to Link Mode (All in
the open/o󰀨 position)

Trouble Shooting
Frequently Asked Questions
Contact
Please call us with any questions. Your satisfaction is our priority.
Call toll free:
1 800 987-6749, Monday-Friday 8:30am-4:30pm EST
Website:
http://www.longrangellc.com
Product Repairs
MAIL TO: Long Range LLC.
26 Tannery St.
Franklin, NH 03235
Please carefully pack and ship, prepaid and insured, to Long Range LLC.
Questions Answers
What should I do if my T4300A isn’t working?
What should I do if my T4300A isn’t turning on?
First, ensure that your T4300A is set to the same
Channel as the trap that you are trying to re.
Second, ensure that your T4300A is set to the
correct Message Length.
Please refer to the Dip Switches Manual
included with your device.
Be sure that the T4300A has a fresh 9-volt
battery.
4
Safety Warning
Long Range LLC’s equipment is used to wirelessly activate clay target machines. Certain safety
precautions should always be practiced while installing and/or using Long Range LLC equipment on
automatic trap machines. Always stay clear of the trap while installing or operating Long Range LLC
equipment.
Long Range LLC equipment is designed to work with manufactured clay target machines and holds
no responsibility for damages caused by modied machines or using the equipment for purposes
other than which it is designed for.
Please do not disassemble or modify the equipment. Long Range LLC does not bear any
responsibility with respect to breakdowns or damages due to disassembling or modifying the
equipment.