Lopi X User manual

,
l n .
OWNER"S MANUAL
LOPI FIREPLACE INSERT
MODEL X
INSTALLATION, OPERATION AND MAINTENANCE HANDBOOK
JUNE 1988
Tested to UL 907 (U.S.A.)
ULC S628 (Canada)
1

l
We welcome you as a new owner of a LOPI wood heating appliance.
In purchasing a LOPI,
you have joined the growing ranks of concerned
individuals whose selection of an energy system reflects both a
concern for efficiency and aesthetics.
We offer our continual support and guidance to help you achieve
the maximum benefit and enjoyment from your wood heating appliance.
You are encouraged to familiarize amiliarize yourself with the Owner's Manual
before installing your wood heating appliance. This manual covers
in detail the necessary steps required in assembling and installing
your wood heating appliance to meet all safety codes. Included are
helpful hints and suggestions which will make the installation of
your new stove or insert an easier and more enjoyable experience.
We at LOPI wish you many years of warmth and satisfaction.

Please record the insert serial number located on the side of the
unit, before installing.
RECORD SERIAL NUMBER HERE
--.
Installing your insert requires some preparation and homework.
It is very important to learn your local building codes. You
may be required to obtain a building permit before installing
your insert. Your local Building Inspection Department will
be
happy to assist you with information regarding installation and
safety requirements in your area.
Also,
notify your home
insurance company that you plan to install a fireplace insert.
Before using the insert,be sure to have a local Building
Inspector approve your installation in writing.
LOPI inserts are intended far installation in accordance with the
Standards for Chimney Fireplaces and Vents NFFA No. 211.
You should inspect your fireplace far good integrity throughout
the system. There should be no missing bricks, mortar, cracks or
heavy deposits of creosote. It is recommended that your
fireplace be cleaned and inspected by
sweep before installing your stove. a professional chimney
NOTE:
DO NOT CONNECT THE INSERT TO A
ANOTHER APPLIANCE OR AIR DISTRIBUTION
NOTE:
LOCK EXISTING FIREPLACE DAMPER
INSTALLING INSERT.
CHIMNEY SYSTEM SERVING
DUCT.
IN "OPEN" POSITION BEFORE
Certain regions also require a directflue connection for insert
installation. For increased heating efficiency we recommend a
direct flue connection,however all LOP1 inserts have been tested
and approved with or without the use of a direct flue connection.
3

L
. l .
Your LOPI fireplace insert will came packaged in several boxes.
These will include:
1. STOVE MASTER BOX -
Includes the stave firebax. Door with
handles,firebrick, baffle, hardware kit, manual, and
ashlip.
2. GLASS BOX -
Includes one piece of glass far the single door
and non-asbestaes fiberglass garketing.
3.
PANEL BOX -
Includes two side panels, one tap panel with
Brass Trim and Hardware.
Accessories available through your local LOPI dealer. These
optional packages include:
1. Reduced clearance mantle shield
2.
Etched glass.
WARNING: CARELESS INSTALLATION IS THE MAJOR CAUSE OF SAFETY
HAZARDS.
CHECK ALL LOCAL BUILDING AND SAFETY CODES BEFORE
INSTALLATION OF THE UNIT.
Your fireplace insert is very heavy and requires at least twa
people to move it safely. The insert can be damaged by
mishandling. Before installing,check and clean your masonry
chimney system thoroughly. If in doubt about it's condition,
seek professional advice from your authorized LOPI dealer
or
certified chimney sweep.
DEALERS ARE TRAINED TO SAFELY INSTALL UNITS AND IT IS A CHOICE WE
HIGHLY RECOMMENDED.
WARNING: DO NOT REMOVE PRICK OR MORTAR FROM EXISTING FIREPLACE
TO INSTALL UNIT. IT IS NECESSARY TO PERMANENTLY SEAL ANY OPENING
BETWEEN THE MASONRY OF THE FIREPLACE AND THE MASONRY FACING.
NOTE:
DO NOT INSTALL IN A ZERO CLEARANCE FIREPLACE!! INSTALL
AND USE ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.