Lotus PC-74ETX User manual

Translation of the original instructions
Installation and operating instructions
KITCHEN WITH OVEN FOR
PROFESSIONAL USE
PC-74ETX , PCQ-74ETX , PCC-74ETX , PC-78ETX , PCQ-78ETX
PCC-78ETX , PC-712ETX , PCQ-712ETX
PCT-74ETX , PCQT-74ETX , PCCT-74ETX , PCT-78ETX , PCQT-78ETX
PCCT-78ETX , PCT-712ETX , PCQT-712ETX
CF4-78ETX , CFQ4-78ETX , CFC4-78ETX , CF6-712ETVX
CFQ6-712ETVX , CF6-712ETX , CFQ6-712ETX
CFV4-78ETX CFVQ4-78ETX
Model LIBR.ISTR.PCX CFX 70E
Code 563007405
Review 1
Edition date 14/01/2020
Language English
LOTUS S.p.A.
Via Calmaor, 46
31020 San Vendemiano
[phone]
[phone]

Contents
Translation of the original instructions
2
Contents
1 INTRODUCTION......................................................................................................................... 3
1.1 Installation drawing...................................................................................................................... 3
1.2 Components................................................................................................................................. 4
1.3 Fixing feet .................................................................................................................................... 14
1.4 Example installation of the appliance........................................................................................... 15
2 GENERAL INFORMATION......................................................................................................... 16
2.1 Declaration of compliance............................................................................................................ 16
2.2 User information, RAEE Directive on waste electrical and electronic equipment ........................ 17
2.3 Technical data table..................................................................................................................... 18
3 INSTALLATION........................................................................................................................... 20
3.1 Delivery checks ............................................................................................................................ 20
3.2 Removing the packaging ............................................................................................................. 20
3.3 Mechanical installation ................................................................................................................. 20
3.4 Electrical/gas connections ........................................................................................................... 20
4 INSTRUCTIONS FOR USE......................................................................................................... 22
4.1 General information ..................................................................................................................... 22
4.2 Lighting and adjusting the open rings.......................................................................................... 22
4.3 Glass-ceramic cooker hob........................................................................................................... 23
4.4 Turning on and adjusting the static oven ..................................................................................... 24
4.5 Turning on and adjusting the fan oven ......................................................................................... 25
4.6 Cooking table for the fan oven ..................................................................................................... 26
5 MAINTENANCE.......................................................................................................................... 28
5.1 Routine......................................................................................................................................... 28
5.2 Spare parts .................................................................................................................................. 29
6 CLEANING.................................................................................................................................. 30
6.1 Routine cleaning.......................................................................................................................... 30
6.2 Cleaning the glass ....................................................................................................................... 30
6.3 Maintenance suggestions............................................................................................................ 31
6.4 How to achieve a brilliant result in three simple steps:................................................................ 32
6.5 How to your SCHOTT CERAN® hob bright and shining for a long time...................................... 33

INTRODUCTION
Translation of the original instructions
3
1 INTRODUCTION
1.1 Installation drawing
FIG. A PC...
A Data Plate
B Electrical connection

FIG. B PC…T..
A Data Plate
B Electrical connection

INTRODUCTION
Translation of the original instructions
4
1.2 Components
FIG. A
1 Square electrical plates
2 Round electrical plates

FIG. B
Radiant heating elements for glass-ceramic appliances

INTRODUCTION
Translation of the original instructions
5
HOB WIRING DIAGRAM (C)
1 Power supply terminal board
2 Switch
3 White indicator light
4 Electrical plate

INTRODUCTION
Translation of the original instructions
6
HOB WIRING DIAGRAM (D)
1 Power supply terminal board
2 Switch
3 White indicator light
4 Electrical plate

INTRODUCTION
Translation of the original instructions
7
HOB WIRING DIAGRAM (E)
1 Power supply terminal board
2 Switch
3 White indicator light
4 Electrical plate


INTRODUCTION
Translation of the original instructions
8
WIRING DIAGRAM (F)
1 Switch
2 Power supply terminal board
3 Radiant resistance
4 Power regulator
5 Relay board
6 White indicator light
7 Residual heat indicator light
8 Transformer

INTRODUCTION
Translation of the original instructions
9
WIRING DIAGRAM (G)
1 Switch
2 Power supply terminal board
3 Radiant resistance
4 Power regulator
5 Relay board
6 White indicator light
7 Residual heat indicator light
8 Transformer

INTRODUCTION
Translation of the original instructions
10
WIRING DIAGRAM OVEN GN 2/1 (H)
1-2 Switch
3 Power supply terminal board
4 Heating element
5 White indicator light
6 Green indicator light
7 Thermostat
8 Safety thermostat

INTRODUCTION
Translation of the original instructions
11
WIRING DIAGRAM OVEN GN 3/1 (I)
1-2 Switch
3 Power supply terminal board
4 Heating element
5 White indicator light
6 Green indicator light
7 Thermostat
8 Safety thermostat

INTRODUCTION
Translation of the original instructions
12
WIRING DIAGRAM VENTILATED OVEN (J)
1 Switch
2 Condenser
3 Power supply terminal board
4 Switching terminal board
5 Motor
6 Heating element
7 White indicator light
8 Green indicator light
9 Safety thermostat
10 Thermostat
11 Transformer

INTRODUCTION
Translation of the original instructions
13
PREDISPOSITION 440V~3 (K)
Electrical technical data table
MODEL WIRING DIAGRAMS
PC...-74ETX C + K
PCQ...-74ETX C + K
PCC...-74ETX F
PC...-78ETX D + K
PCQ...-78ETX D + K
PCC...-78ETX G
PC...-712ETX E + K
PCQ...-712ETX E + K

Electrical technical data table
MODEL WIRING DIAGRAMS
CF4-78ETX (D + K) + H
CFQ4-78ETX (D + K) + H
CFC4-78ETX G + H
CF6-712ETVX (E + K) + H
CFQ6-712ETVX (E + K) + H
CF6-712ETX (E + K) + I
CFQ6-712ETX (E + K) + I
CFV4-78ETX (D + K) + J
CFVQ4-78ETX (D + K) + J


INTRODUCTION
Translation of the original instructions
14
1.3 Fixing feet

INTRODUCTION
Translation of the original instructions
15
1.4 Example installation of the appliance

GENERAL INFORMATION
Translation of the original instructions
16
2 GENERAL INFORMATION
2.1 Declaration of compliance
The manufacturer declares that the appliances comply with the requirements of the regulation GAR
2016/426 for the gas part and directive 2014/30/EU,2014/35/EU for the electrical part. Installation must be
performed in compliance with current regulations, especially with regard to ventilation of the premises and
the exhaust gas evacuation system.
·Read the warnings in this manual carefully. They provide important information about safe installation,
use and maintenance.
·The instruction manual must be kept for the entire duration of the equipment and made available to users
for every possible consultation. The manual should be consulted for any information concerning
installation, use and maintenance of the appliance.
·After removing the packaging, check the integrity of the equipment.
·All packaging materials (plastic bags, polystyrene, staples, etc.) must be disposed of in compliance with
current regulations.
·Before connecting the appliance, make sure that the information on the data plate matches the electricity
and gas mains where the appliance is installed. The manufacturer accepts no liability if the
equipment is not connected in accordance with current regulations.
·Always keep all parts of the equipment clean to avoid the risk of oxidation/rust and/or aggression by
chemical agents.
·The equipment must only be used by personnel trained for the purpose.
·The installation must be implemented by professionally qualified personnel in accordance with
the manufacturer's instructions and current reference standards.
·The electrical safety of this equipment is only ensured when it is correctly connected to an effective
ground/earth system as required by current electrical safety standards. The manufacturer cannot be held
liable for any damage caused if the system is not connected to ground/earth.
·Before carrying out any cleaning or maintenance tasks on the equipment, unplug it from the electricity
mains. In the event of faults or malfunctions, always deactivate the appliance.
·Repair work of any kind must only be performed by qualified personnel.
·This appliance must only be used for its expressly intended purpose for cooking or heating food. Any
other use is considered improper.
·The appliance is intended for professional use and must be used by trained personnel.
·The installation and possible transformation to another power supply voltage (if envisaged), or
transformation for operation with another type of gas, must be implemented exclusively by qualified and
authorised professional personnel.
·Before using the appliance, carefully clean all surfaces intended to come into contact with food.
·The manufacturer declines any and all liability for any direct or indirect damage resulting from improper
use of the equipment. The manufacturer declines any and all liability for damage caused by incorrect
installation, tampering, poor maintenance and unskilled use. Moreover, the manufacturer declines any
liability for possible inaccuracies that may be contained in this booklet attributable to errors in
transcription or printing and equally reserves the right to make any changes to the product it deems
useful and/or necessary without compromising its essential characteristics.
·The manufacturer cannot be held liable for any damage caused by failure to comply with these
basic standards and all other use and maintenance standards contained in this booklet.

GENERAL INFORMATION
Translation of the original instructions
17
2.2 User information, RAEE Directive on waste electrical and
electronic equipment
With regard to the regulatory framework of reference of the European Community, we remind the user of the
following:

·Used AAE (Electrical and Electronic Equipment) products must be collected separately
·The user can carry out this collection in the RAEE collection systems and return the equipment to the
distributor when purchasing a new one
·Plus being RoHS compatible, (in accordance with Directive 2011/65/EU on the restriction of the use of
certain hazardous substances in electrical and electronic equipment) the potential effects on the
environment and human health may be due to the misuse of the same equipment or parts of it
·The symbol next to the rating plate indicates the obligation of separate collection
·The penalties provided for in the event of improper disposal of RAEE (Waste Electrical and Electronic
Equipment) are those provided for by the national transpositions of European Directives 2012/19/EU

GENERAL INFORMATION
Translation of the original instructions
18
2.3 Technical data table
Technical data table PC S70EX
MODEL DIMENSIONS POWER SUPPLY MAXIMUM INPUT
(A)
MAXIMUM
POWER (kW)
Silicon POWER
SUPPLY CABLE
PC-74ETX 40x70x90h 400V~3 50/60 Hz 11,26 5,2 4 x 2,5 mm²
PC-74ETX 40x70x90h 440V~3 50/60 Hz 10,23 5,2 4 x 2,5 mm²
PCT-74ETX 40x70x29h 400V~3 50/60 Hz 11,26 5,2 4 x 2,5 mm²
PCT-74ETX 40x70x29h 440V~3 50/60 Hz 10,23 5,2 4 x 2,5 mm²
PCQ-74ETX 40x70x90h 400V~3 50/60 Hz 11,26 5,2 4 x 2,5 mm²
PCQ-74ETX 40x70x90h 440V~3 50/60 Hz 10,23 5,2 4 x 2,5 mm²
PCQT-74ETX 40x70x29h 400V~3 50/60 Hz 11,26 5,2 4 x 2,5 mm²
PCQ-74ETX 40x70x90h 440V~3 50/60 Hz 10,23 5,2 4 x 2,5 mm²
PCC-74ETX 40x70x90h 400V~3 50/60 Hz 10,83 5 4 x 2,5 mm²
PCCT-74ETX 40x70x29h 400V~3 50/60 Hz 10,83 5 4 x 2,5 mm²
PC-78ETX 80x70x90h 400V~3 50/60 Hz 17,2 10,4 4 x 2,5 mm²
PC-78ETX 80x70x90h 440V~3 50/60 Hz 15,63 10,4 4 x 2,5 mm²
PCT-78ETX 80x70x29h 400V~3 50/60 Hz 17,2 10,4 4 x 2,5 mm²
PCT-78ETX 80x70x29h 440V~3 50/60 Hz 15,63 10,4 4 x 2,5 mm²
PCQ-78ETX 80x70x90h 400V~3 50/60 Hz 17,2 10,4 4 x 2,5 mm²
PCQ-78ETX 80x70x90h 440V~3 50/60 Hz 15,63 10,4 4 x 2,5 mm²
PCQT-78ETX 80x70x29h 400V~3 50/60 Hz 17,2 10,4 4 x 2,5 mm²
PCQT-78ETX 80x70x29h 440V~3 50/60 Hz 15,63 10,4 4 x 2,5 mm²
PCC-78ETX 80x70x90h 400V~3 50/60 Hz 16,54 10 4 x 2,5 mm²
PCCT-78ETX 80x70x29h 400V~3 50/60 Hz 15,03 10 4 x 2,5 mm²
PC-712ETX 120x70x90h 400V~3 50/60 Hz 22,52 15,6 4 x 2,5 mm²
PC-712ETX 120x70x90h 440V~3 50/60 Hz 20,47 15,6 4 x 2,5 mm²
PCT-712ETX 120x70x29h 400V~3 50/60 Hz 22,52 15,6 4 x 2,5 mm²
PCT-712ETX 120x70x29h 440V~3 50/60 Hz 20,47 15,6 4 x 2,5 mm²
PCQ-712ETX 120x70x90h 400V~3 50/60 Hz 22,52 15,6 4 x 2,5 mm²
PCQ-712ETX 120x70x90h 440V~3 50/60 Hz 20,47 15,6 4 x 2,5 mm²
PCQT-712ETX 120x70x29h 400V~3 50/60 Hz 22,52 15,6 4 x 2,5 mm²
PCQT-712ETX 120x70x29h 440V~3 50/60 Hz 20,47 15,6 4 x 2,5 mm²


GENERAL INFORMATION
Translation of the original instructions
19
Technical data table CF S70EX
MODEL DIMENSIONS POWER SUPPLY MAXIMUM INPUT
(A)
MAXIMUM
POWER (kW)
Silicon POWER
SUPPLY CABLE
CF4-78ETX 80x70x90h 400V~3 50/60 Hz 25,19 15,4 4 x 4 mm²
CF4-78ETX 80x70x90h 440V~3 50/60 Hz 22,9 15,4 4 x 4 mm²
CFQ4-78ETX 80x70x90h 400V~3 50/60 Hz 25,19 15,4 4 x 4 mm²
CFQ4-78ETX 80x70x90h 440V~3 50/60 Hz 22,9 15,4 4 x 4 mm²
CFC4-78ETX 80x70x90h 400V~3 50/60 Hz 24,54 15 4 x 4 mm²
CF6-712ETVX 120x70x90h 400V~3 50/60 Hz 30,77 20,6 4 x 4 mm²
CF6-712ETVX 120x70x90h 440V~3 50/60 Hz 29,97 20,6 4 x 4 mm²
CFQ6-712ETVX 120x70x90h 400V~3 50/60 Hz 30,77 20,6 4 x 4 mm²
CFQ6-712ETVX 120x70x90h 440V~3 50/60 Hz 29,97 20,6 4 x 4 mm²
CF6-712ETX 120x70x90h 400V~3 50/60 Hz 33,38 22,5 4 x 6 mm²
CF6-712ETX 120x70x90h 440V~3 50/60 Hz 30,34 22,5 4 x 6 mm²
CFQ6-712ETX 120x70x90h 400V~3 50/60 Hz 33,38 22,5 4 x 6 mm²
CFQ6-712ETX 120x70x90h 440V~3 50/60 Hz 30,34 22,5 4 x 6 mm²
CFV4-78ETX 80x70x90h 400V~3 50/60 Hz 24,85 15,72 4 x 4 mm²
CFV4-78ETX 80x70x90h 440V~3 50/60 Hz 22,59 15,72 4 x 4 mm²
CFVQ4-78ETX 80x70x90h 400V~3 50/60 Hz 24,85 15,72 4 x 4 mm²
CFVQ4-78ETX 80x70x90h 440V~3 50/60 Hz 22,59 15,72 4 x 4 mm²


INSTALLATION
Translation of the original instructions
20
3 INSTALLATION
3.1 Delivery checks
On delivery, it is important to check the following:

·External conditions of the packaging
·The general status of the equipment
·The conformity of the model with the information in the technical data plate and the instruction manual
·The conformity of the equipment and components to the order form

3.2 Removing the packaging
While removing the packaging, take care not to damage the appliance. Remove the protective film from the
stainless steel and eliminate any traces of glue. Do not smoke. Perform this operation away from sources of
heat and wear protective gloves. Do not disperse packaging material in the environment, keep it out of the
reach of children and dispose in compliance with current legislation.

3.3 Mechanical installation
Place the appliance on a flat base. Adjust and stabilise the appliance by acting on the support feet. Make
sure that the surrounding walls and/or equipment are capable of withstanding the heat emitted by this
appliance. Connect the water supply (if necessary).

Caution

Do not install the appliance near equipment/machines used in cold processes. If the appliance
has to be installed close to cold process equipment, it is advisable to install non-combustible
thermal insulating material and/or neutral elements between them.

3.4 Electrical/gas connections
Before being offered for sale on the market, the appliance was subjected to gas and electrical testing (as
required). The appliance is supplied without a power cable. The installation technician must connect the
equipment in compliance with current safety regulations on the basis of the power of the appliance.
Note

The ID plate is located in the compartment inside the door for appliances with compartments, or on
the left side for appliances with an oven or a top. A second plate with the model and serial number is
located inside the dashboard and a third is included with the certificate of conformity. The serial
number can also be tracked from the sales document (after 2008). The plate has all the data needed
for correct electrical installation. The installation and possible conversion to another power supply
voltage (if envisaged) must be implemented exclusively by professionally qualified and authorized
personnel. Before using the appliance, carefully clean all surfaces intended to come into contact with
food.
