Electrolux Professional IC43316 User manual

01103042/GB
08.18
Operating handbook
Flatwork ironers
IC43316 – IC43320
Australia
Translated from french

01103042
Page
Notice Date
OPERATING
HANDBOOK
00606 0 00
Table of contents
The manufacturer reserves the right to modify construction and equipment characteristics.
Pages/Chapters
General operating
Precaution for use ...............................................................................................1/1
General
Identication plate ................................................................................................2/2
Method of use
Standard control console .....................................................................................1/3
Starting machine with standard console ..............................................................2/3
Stopping machine with standard console ............................................................3/3
Additional instructions ..........................................................................................4/3
Precautions for use ..............................................................................................5/3
Using the handle ..................................................................................................7/3
Safety
Locking and tagging procedure ...........................................................................3/4
Safety devices .....................................................................................................4/4
Operating incidents
The linen remains stuck to the cylinder ...............................................................1/5
When the linen comes off the dryer-ironer it is not dry ........................................1/5
The heating does not work or works badly ..........................................................2/5
The machine temperature drops .........................................................................3/5
The machine stops suddenly ...............................................................................3/5
Additional instructions ..........................................................................................4/5
Maintenance
Preventive maintenance ......................................................................................1/6
Replacing ironing bands ...........................................................................................5/6
Gas train ..............................................................................................................7/6
Appendices
Explanation of graphic symbols ...........................................................................1/7
Explanation of washing symbols .........................................................................2/7
Conversion of measurement units .......................................................................3/7
Lubrication table ................................................................................................4/7
Service and any replacement parts may be obtained on Web site: www.electrolux.com.au.

01103042
PageNotice Date
OPERATING
HANDBOOK
0606 1 1 111. General operating
Precaution for use
• The machine should not be used by children.
• This ironer must be used exclusively for textiles appropriate for machine ironing, which
have been previously and exclusively washed in water.
• Blankets should not be ironed.
• Be careful with synthetic linen and also with printed linen. They can melt and stick on the
cylinder.
• Do not iron articles that contain plastic, foam, sponge rubber or similarly textured rubber-
like materials.
• Do not iron linens coated with solvent, paint, wax, grease or any easily inammable
products.
THIS APPLIANCE SHALL NOT BE USED TO DRY OFF SOLVENTS OR
DRY-CLEANING FLUIDS.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE
WHILE IT IS IN OPERATION.
DO NOT MODIFY THIS APPLIANCE.

01103042
Page
Notice Date
OPERATING
HANDBOOK
11004 2
Before any use, it is compulsory to read the instruction handbook.
Users must have learnt how to the machine operates.
The identication plate is situated on the left side.
This machine should be installed in conformance to the health and safety regula-
tions, and only used in a sufciently aerated area.
Check the instructions before installing or using the machine.
In the machine you should have found a set of instructions and a servicing poster to display
in your laundry.
You must have found with this handbook, a crank for the manual drive of the cylinder.
Depending on its destination, the dryer ironer is delivered bare or may be placed on a trans-
port pallet and/or packed with plastic lm.
In some cases, it may be delivered in maritime packing (wood crate).
Please refer to the handling chapter in this instruction handbook for a description of handling
operations.
2. General
Fresh air ventilation openings shall not be blocked and or sealed.

01103042
PageNotice Date
OPERATING
HANDBOOK
D1146
2
0111 2
For safety rea-
sons use only
original spare
parts.
TYPE : IC43320
SERIAL N° : 40433/0000698
QC N° : 82400034
PROD. N° : 9882821210F
CAPACITY : ____ l ; ___,_ kg
P. MAX. : 500 W
0.18 kW ISOL. CLAS : F
_____ W
400 V 3 50 Hz
12 A
ELECTROLUX LAUNDRY
SYSTEMS FRANCE
10430 Rosières-près-Troyes
FRANCE
Made in FRANCE
NG: 1.13 kPa
NG TPP 0.90 kPa
Injector: 270
Gas consumption
105 MJ/h
Propane 2.75 kPa
Propane TPP
2.65kPa
Injector: 160
Gas consumption
100 MJ/h
32101642
Date : 13/10/2010
Certicate of compliance number:
AGA Approval
number: 7709
IP 24D
The machines described in this handbook have an ironing capacity of 1.650 m ( 65") or 2.065
m (811/3") wide according to their type.
The ironing speed can be adjusted according to the linen texture and its degree of moisture.
The temperature of the ironing cylinder can also be adjusted by a thermostat.
The parameters are displayed by a control panel.
2. General
Identication
plate
Adjustment label
(for gas machine only)
Identication plate

01103042
Page
Notice Date
OPERATING
HANDBOOK 2
1004 3
2. General
This page is left blank on purpose.

01103042
PageNotice Date
OPERATING
HANDBOOK
0606 13
D1323
3
2
1 8
4 5
6
7
9
3. Method of use
Standard control console
1. "Voltage" indicator
2. "Stop" switch
3. "On" switch
4. "Ironing speed adjustment" potentiometer
5. "Cylinder temperature" display
6. "Heating" indicator on
7. Gas heating "Ignitor failure" indicator
8. "On / Off" heating switch with "On" indicator
9. "Ironing temperature selection" thermostat

01103042
Page
Notice Date
OPERATING
HANDBOOK
0606 2 3
3. Method of use
Starting machine with standard console
- Turn main section switch to I (ON), the indicator (1) "voltage" lights".
- Turn the potentiometer (4) to the minimum speed.
- Adjust thermostat (5) on required temperature. Usual ironing temperature is around
175 °C (347 °F) for cotton.
- Wait for initialising of the thermostat.
- Press "" button .
- Adjust ironing temperature with "" or "" button.
- Press "Set" button.
- Press button (3) "On".
The cylinder and the guiding bands rotate.
The fan works and draws the air out of the machine to outside the building.
- Press switch (8) "heating on", the key indicator lights. The heating indicator (6) lights. The
temperature rise is reached after approximately 12 min for a temperature of 175 °C (347
°F). The heating indicator (6) switches off as soon as the required ironing temperature is
reached.
- Check that the nger protection is working. The nger protection must stop the machine
when it is touched.
Press button (3) "On" to restart the machine.
- Adjust potentiometer (4) on an average speed and start ironing.
- Ajust the ironing speed depending on the textile processed and the moisture rate of the
linen.
- If the pipe burner is secured, the indicator (6) switches off and the indicator (7) lights ; (to
restart the machine, press "STOP HEATING" and then "HEATING ON" (8).

01103042
PageNotice Date
OPERATING
HANDBOOK
0606 33
D1434
orange indicator/
button
Stopping machine with standard console
• In order to extend the lifetime of your machine and its components, observe the following
instructions to stop the heating.
• Press switch (6) "Heating stop", its indicator switches off. The "Heating" indicator (8)
switches off too.
• Continue to feed in damp laundry until the temperature of the cylinder no longer produces
satisfactory drying.
• Turn the general switch situated on the left casing to O (off).
CAREFUL : At any time, it is possible to stop the machine by pressing key (2) "General
stop", a high temperature of the ironing cylinder may damage the ironing strips.
3. Method of use
The appliance is supplied with visual alarms (orange indicators) to draw the attention of the
operator when an interlock has « tripped » or a burner failure has occured. To restart the
appliance, indicated defaults should be reseted by the orange button tted in front face of the
left casing.
In case of frequently or permanently default happening, it is necessary to nd the default
cause and eventually replace the faulty component.
Interlocks tted to this appliance include an air pressure switch, over-temperature protection,
nger guard, low gas pressure switch.

01103042
Page
Notice Date
OPERATING
HANDBOOK
1004 4 3
3. Method of use
D1097
Additional instructions to optimise a dryer-ironer.
When ironing small sheets or small washing, pass abreast the washing of the heating cylin-
der to provide correct regulation of the cylinder temperature.
As a general rule, the whole of the cylinder should be used (1). Either iron the linen from the
front (2) or iron alternately (3), which makes maximum use of the heat units available over
the surface of the cylinder. It also overcomes difculties arising from random control values
caused by partial use of the cylinder.
Cylinder Linen

01103042
PageNotice Date
OPERATING
HANDBOOK
1004 53
123
D0411
Practices to avoid
• Make sure that the width of the washing does not exceed the useful width of the machine.
• Sizes not tting the cylinder working length, partial use of the cylinder.
• Blankets should not be ironed.
Practices not recommended
• Worn polycotton sheets (cotton worn away) : uneven nish look when folded, high static
electricity.
• Large cotton or ax-made sheets > 200 g/m².
Cautions
• Prepare the large sheets before feeding.
• Avoid the torn, worn or holed sheets, that may hook and alter the measurements and the
longitudinal folding.
• Comply with the mini-maxi sizes of sheets.
3. Method of use
Draw- Fitted- Comforter Butcher's Linen Linen
sheets sheets cases apron < 200 g/m² > 200 g/m²
Flatwork ironer    
1 Fitted-sheet 2 Comforter cases with ap 3 Butcher's apron
 Yes  Cautions   Practices to avoid

01103042
Page
Notice Date
OPERATING
HANDBOOK
D1149
0305 6 3
D1203
D1204
Handle
Using the handle
The dryer ironer is tted with a handle.
This is very useful to take out the washing
if there is a power failure while you are
ironing; or you can use it to feed a piece
of wet washing to protect the ironing
bands when the ironing temperature is too
high.
3. Method of use
Using the tipping feed bin
The dryer-ironer is equipped with a tipping
feed bin. This is very useful for letting
large items hang to assist feeding and
allow smoothing of linen by hand.
For ease of opening, lift the bin slightly
before pivoting.

01103042
PageNotice Date
OPERATING
HANDBOOK
1004 73
This page is left blank on purpose.
3. Method of use

01103042
Page
Notice Date
OPERATING
HANDBOOK
1004 1 4
4. Safety
CAUTION
Do not use the machine unless it is plugged
into a correctly earthed power socket comp-
lying with standards in force.
CAUTION
For your personal safety, never use the ma-
chine without the protective housings.
CAUTION
Disconnect the machine electrical power
supply before doing any repair or servicing
work.
WARNING
The presence of dangerous mechanims
inside the machine can cause serious inju-
ries. Respect all safety instructions before
doing any work on the machine. Replace
protective casings after doing any work.

01103042
PageNotice Date
OPERATING
HANDBOOK
1004 244. Safety
All repair and servicing work must be undertaken by a competent person.
Never wear full clothes during work (wide sleeves, ties, scarves, etc.).
Disconnect all energy sources and let the ironing cylinder cool down before doing any work
on the machine.
In order to avoid any danger of re or explosion, never use inammable products to clean the
machine.
If you smell gas, turn off the gas supply, open the windows, do not touch any switches and
inform the maintenance service.
Evacuation of vapour from a dryer ironer with gas heating must never be connected to the
evacuation used for a gas heating machine and a dry cleaning machine or other machine of
the same type.
SAFETY
Never iron if the mobile safety protector
(hand protection bar) is not operating.
CAUTION
The temperature of the ironing cylinder
after use can reach 200 °C (392 °F) and
can cause serious burns if you touch it.
Allow the machine to cool down before
doing any repair or servicing work.
IMPORTANT
To ensure optimal operation of the ma-
chine (gas heating, electronic boards,
etc.), ensure that the ambient tempera-
ture does not fall below 15°C (59 °F).

01103042
Page
Notice Date
OPERATING
HANDBOOK
1004 3 4
2
1
3
4
Locking and tagging procedure
A red insert at the beginning of this instruction handbook schematically shows the locking
and tagging procedure described below. If you wish, you can detach this insert and display it
close to the machine to remind maintenance personnel of the safety instructions.
Put the main switch
to Off and lock the
handle with a pa-
dlock in one of the
three holes provided
for this purpose.
Always respect items
2, 3 and 4 carefully
before doing any re-
pair or maintenance
work on the machine.
Open the xed protec-
tors (casings, doors)
with the key provided
or a special tool.
Close and carefully
lock the xed protec-
tors.
Unlock the stop
valves and the
main switch.
Do the maintenance.
Close the stop valves for
the other sup-
plies (steam,gas,
thermal uid,
compressed air)
to stop and lock
their handle with a
padlock.
4. Safety

01103042
PageNotice Date
OPERATING
HANDBOOK
1004 44
Safety devices
Feed safety device
The space between the feed safety ap and the drive bands is too small for you to enter your
ngers. The machine stops automatically as soon as the ap is pushed in.
Protection of motors
The motors have overload protection :
• by thermomagnetic circuit breakers and
• by the electrical selector (for movement).
Restarting the machine
After each stoppage of the machine, power cut, emergency stop, or activation of the feed
safety, it will then be possible to start again:
- in the case of a machine with a standard console, only after pressing the green button of
the panel;
- in the case of a machine with a DIAMMS console, only after pressing one of the buttons of
the control panel.
Gas heating
The gas burner is ignited and the ame is controlled by an electronic box that provides inte-
gral safety, for example if the ue draft is poor or if the gas supply is cut off.
If you have a DIAMMS console, a ashing message on the control panel signals that the
system has been set to safe.
If you have a standard console, the orange lamp signals that the system has been set to
safe. If this lamp ashes this signals that the machine has overheated.
A pressure switch connected to the combustion products outlet turns off the machine’s hea-
ting function should extraction problems arise.
Accessibility
All casings can be disassembled using a special tool.
Heating safety device
The control panel applies an initial safety level at the time the machine starts up.
In the case of a DIAMMS console, if the temperature has not been reached after a preset
time the heating order is then interrupted.
Similarly, in the case of a DIAMMS console, operation of heating is conditional on the cylin-
der rotating. If for any reason whatever the cylinder stops, heating of the machine stops.
A safety thermostat, which is independent of all electronic systems, limits the heating tem-
perature of the ironing cylinder in all circumstances (except in the case of a steam heating
machine).
4. Safety

01103042
Page
Notice Date
OPERATING
HANDBOOK
1004 4
5
4. Safety
Power supply failure
If there is a mains power supply failure, use the handle to remove any washing engaged in
the machine. If the temperature is too high, use the handle to feed some wet washing and
protect the ironing bands.

01103042
PageNotice Date
OPERATING
HANDBOOK
1004 64
SAFETY
Make sure that the protection casings are in position before use.
Complementary instructions for operation
Check daily that the hand safety bar is working correctly, the machine must stop when you
press it. The screen on control panel displays "Emergency Stop/ Reset Push Button". Press
any key to resume ironing.
Ironing Temperature Display
The control enclosure includes an electronic thermostat panel which shows in real time the
temperature of the ironing cylinder.
A running temperature over the selected temperature is normal. This happening is not a fai-
lure of measuring devices but it is due to heating inertia.
In automatic mode, temperature and speed management are handled by the machine itself.
Fire-related risks.
Should a re breakout inside the machine, it is recommended that you use a CO2 extin-
guisher.
Note : in the case of a machine using gas heating, it is strictly forbidden to attempt to put
out the re before having rst turned off the gas inlet valve.
The client must ensure conformity towards the Labour Code and his supplier of re-ghting
equipment who issues the Q4 certicate to him.
Repair and maintenance work on the machine.
All work on the machine must be carried out by qualied personnel, able to carry out the work
required.
Ensure that the applicable safety conditions for the destination country are fully observed.
4. Safety