Lotus PC-94ET User manual

Translation of the original instructions
Installation and operating instructions
KITCHEN WITH OVEN FOR
PROFESSIONAL USE
PC-94ET , PCQ-94ET , PCC-94ET , PC-98ET , PCQ-98ET , PCC-98ET
PC-912ET , PCQ-912ET , PC-916ET , PCQ-916ET PCT-94ET , PCQT-94ET ,
PCCT-94ET , PCT-98ET , PCQT-98ET , PCCT-98ET , PCT-912ET ,
PCQT-912ET , PCT-916ET , PCQT-916ET CF4-98ET , CFQ4-98ET ,
CFC4-98ET , CF6-912ETV , CFQ6-912ETV CF6-912ET , CFQ6-912ET ,
CF8-916ETV , CFQ8-916ETV , CF8-916ET CFQ8-916ET CFV4-98ET ,
CFVQ4-98ET , CFVC4-98ET CFV6-912ETV , CFVQ6-912ETV
Model LIBR.ISTR.PC CF90E
Code 563008204
Review 1
Edition date 15/04/2019
Language English
LOTUS S.p.A.
Via Calmaor, 46
31020 San Vendemiano
[phone]
[phone]

Contents
Translation of the original instructions
2
Contents
1 INTRODUCTION......................................................................................................................... 3
1.1 Installation drawing...................................................................................................................... 3
1.2 Components................................................................................................................................. 4
1.3 Example installation of the appliance........................................................................................... 16
2 GENERAL INFORMATION......................................................................................................... 17
2.1 Declaration of compliance............................................................................................................ 17
2.2 User information, RAEE Directive on waste electrical and electronic equipment ........................ 18
2.3 Technical data table..................................................................................................................... 18
3 INSTALLATION........................................................................................................................... 21
3.1 Delivery checks ............................................................................................................................ 21
3.2 Removing the packaging ............................................................................................................. 21
3.3 Mechanical installation ................................................................................................................. 21
3.4 Electrical/gas connections ........................................................................................................... 21
4 INSTRUCTIONS FOR USE......................................................................................................... 23
4.1 General information ..................................................................................................................... 23
4.2 Lighting and adjusting the open rings.......................................................................................... 23
4.3 Glass-ceramic cooker hob........................................................................................................... 24
4.4 Turning on and adjusting the static oven ..................................................................................... 25
4.5 Turning on and adjusting the fan oven ......................................................................................... 26
4.6 Cooking table for the fan oven ..................................................................................................... 27
5 MAINTENANCE.......................................................................................................................... 29
5.1 Routine......................................................................................................................................... 29
5.2 Spare parts .................................................................................................................................. 30
6 CLEANING.................................................................................................................................. 31
6.1 Routine cleaning.......................................................................................................................... 31
6.2 Cleaning the glass ....................................................................................................................... 31
6.3 Maintenance suggestions............................................................................................................ 32
6.4 How to achieve a brilliant result in three simple steps:................................................................ 33
6.5 How to your SCHOTT CERAN® hob bright and shining for a long time...................................... 34

INTRODUCTION
Translation of the original instructions
3
1 INTRODUCTION
1.1 Installation drawing
FIG. 1 PC…, CF…
A Data Plate
B Electrical connection

FIG. 2 PC...T
A Data Plate
B Electrical connection

INTRODUCTION
Translation of the original instructions
4
1.2 Components
FIG. A

INTRODUCTION
Translation of the original instructions
5
FIG. B
1 Square electrical plates
2 Round electrical plates

Radiant heating elements for glass-ceramic appliances


INTRODUCTION
Translation of the original instructions
6
WIRING DIAGRAM (A)
WIRING DIAGRAM (B)
1 Power supply terminal board
2 Switch
3 Electrical plate
4 White indicator light

INTRODUCTION
Translation of the original instructions
7
WIRING DIAGRAM (C)
1 Power supply terminal board
2 Switch
3 Electrical plate
4 White indicator light

INTRODUCTION
Translation of the original instructions
8
WIRING DIAGRAM (D)
1 Power supply terminal board
2 Switch
3 Electrical plate
4 White indicator light

INTRODUCTION
Translation of the original instructions
9
WIRING DIAGRAM (E)
1 Power supply terminal board
2 Switch
3 Electrical plate
4 White indicator light

INTRODUCTION
Translation of the original instructions
10
WIRING DIAGRAM (F)
1 Switch
2 Power supply terminal board
3 Radiant resistance
4 Power regulator
5 Relay board
6 White indicator light
7 Residual heat indicator light


INTRODUCTION
Translation of the original instructions
11
WIRING DIAGRAM (G)
1 Switch
2 Power supply terminal board
3 Radiant resistance
4 Power regulator
5 Relay board
6 White indicator light
7 Residual heat indicator light

COMMUTATION

INTRODUCTION
Translation of the original instructions
12
WIRING DIAGRAM OVEN GN 2/1 (H)
1 Switch
2 Power supply terminal board
3 Heating element
4 White indicator light
5 Green indicator light
6 Thermostat
7 Safety thermostat


INTRODUCTION
Translation of the original instructions
13
WIRING DIAGRAM OVEN GN 3/1 (I)
1 Switch
2 Power supply terminal board
3 Heating element
4 White indicator light
5 Green indicator light
6 Thermostat
7 Safety thermostat


INTRODUCTION
Translation of the original instructions
14
VENTILATED ELECTRICAL OVEN (L)
1 Switch
2 Condenser
3 Power supply terminal board
4 Switching terminal board
5 Motor
6 Heating element
7 White indicator light
8 Green indicator light
9 Safety thermostat
10 Thermostat


INTRODUCTION
Translation of the original instructions
15
Wiring diagram reference table
MODELS TERMINAL BOARD 1 TERMINAL BOARD 2
PC...-94ET FIG. C /
PCQ...-94ET FIG. C /
PCC...-94ET FIG. F /
PC...-98ET FIG. D /
PCQ...-98ET FIG. D /
PCC...-98ET FIG. G /
PC...-912ET FIG. E /
PCQ...-912ET FIG. E /
PC…-916ET FIG. C + FIG. E /
PCQ…-916ET FIG. C + FIG. E /

MODELS TERMINAL BOARD 1 TERMINAL BOARD 2
CF4-98ET FIG. D + FIG. H /
CFQ4-98ET FIG. A + FIG. B + FIG. H /
CFC4-98ET FIG. G + FIG. H /
CF6-912ETV FIG. H + FIG. E /
CFQ6-912ETV FIG. H + FIG. E /
CF6-912ET FIG. I + FIG. E /
CFQ6-912ET FIG. I + FIG. E /
CF8-916ETV FIG. E FIG. C + FIG. I
CFQ8-916ETV FIG. E FIG. C + FIG. I
CF8-916ET FIG. E FIG. C + FIG. H + FIG. H
CFQ8-916ET FIG. E FIG. C + FIG. H + FIG. H
CFV4-98ET FIG. D + FIG. L /
CFVQ4-98ET FIG. A + FIG. B + FIG. L /
CFVC4-98ET FIG. G + FIG. L /
CFV6-912ETV FIG.L + FIG. E /
CFVQ6-912ETV FIG.L + FIG. E /


INTRODUCTION
Translation of the original instructions
16
1.3 Example installation of the appliance

GENERAL INFORMATION
Translation of the original instructions
17
2 GENERAL INFORMATION
2.1 Declaration of compliance
The manufacturer declares that the appliances comply with the requirements of the regulation GAR
2016/426 for the gas part and directive 2014/30/EU,2014/35/EU for the electrical part. Installation must be
performed in compliance with current regulations, especially with regard to ventilation of the premises and
the exhaust gas evacuation system.

·Read the warnings in this manual carefully. They provide important information about safe installation,
use and maintenance.
·The instruction manual must be kept for the entire duration of the equipment and made available to users
for every possible consultation. The manual should be consulted for any information concerning
installation, use and maintenance of the appliance.
·After removing the packaging, check the integrity of the equipment.
·All packaging materials (plastic bags, polystyrene, staples, etc.) must be disposed of in compliance with
current regulations.
·Before connecting the appliance, make sure that the information on the data plate matches the electricity
and gas mains where the appliance is installed. The manufacturer accepts no liability if the
equipment is not connected in accordance with current regulations.
·Always keep all parts of the equipment clean to avoid the risk of oxidation/rust and/or aggression by
chemical agents.
·The equipment must only be used by personnel trained for the purpose.
·The installation must be implemented by professionally qualified personnel in accordance with
the manufacturer's instructions and current reference standards.
·The electrical safety of this equipment is only ensured when it is correctly connected to an effective
ground/earth system as required by current electrical safety standards. The manufacturer cannot be held
liable for any damage caused if the system is not connected to ground/earth.
·Before carrying out any cleaning or maintenance tasks on the equipment, unplug it from the electricity
mains. In the event of faults or malfunctions, always deactivate the appliance.
·Repair work of any kind must only be performed by qualified personnel.
·This appliance must only be used for its expressly intended purpose for cooking or heating food. Any
other use is considered improper.
·The appliance is intended for professional use and must be used by trained personnel.
·The installation and possible transformation to another power supply voltage (if envisaged), or
transformation for operation with another type of gas, must be implemented exclusively by qualified and
authorised professional personnel.
·Before using the appliance, carefully clean all surfaces intended to come into contact with food.
·The manufacturer declines any and all liability for any direct or indirect damage resulting from improper
use of the equipment. The manufacturer declines any and all liability for damage caused by incorrect
installation, tampering, poor maintenance and unskilled use. Moreover, the manufacturer declines any
liability for possible inaccuracies that may be contained in this booklet attributable to errors in
transcription or printing and equally reserves the right to make any changes to the product it deems
useful and/or necessary without compromising its essential characteristics.
·The manufacturer cannot be held liable for any damage caused by failure to comply with these
basic standards and all other use and maintenance standards contained in this booklet.

GENERAL INFORMATION
Translation of the original instructions
18
2.2 User information, RAEE Directive on waste electrical and
electronic equipment
With regard to the regulatory framework of reference of the European Community, we remind the user of the
following:

·Used AAE (Electrical and Electronic Equipment) products must be collected separately
·The user can carry out this collection in the RAEE collection systems and return the equipment to the
distributor when purchasing a new one
·Plus being RoHS compatible, (in accordance with Directive 2011/65/EU on the restriction of the use of
certain hazardous substances in electrical and electronic equipment) the potential effects on the
environment and human health may be due to the misuse of the same equipment or parts of it
·The symbol next to the rating plate indicates the obligation of separate collection
·The penalties provided for in the event of improper disposal of RAEE (Waste Electrical and Electronic
Equipment) are those provided for by the national transpositions of European Directives 2012/19/EU
2.3 Technical data table
Technical data table - PC S90E
MODEL DIMENSIONS POWER SUPPLY
MAXIMUM
ABSORPTION
(A)
MAXIMUM
POWER
(kW)
POWER SUPPLY
CABLE
silicon type
PC-94ET 40x90x90h 400V~2N 50/60 Hz 15,22 7 4 x1,5 mm²
PCT-94ET 40x90x29h 400V~2N 50/60 Hz 15,22 7 4 x1,5 mm²
PCQ-94ET 40x90x90h 400V~2N 50/60 Hz 17,39 8 4 x 2,5 mm²
PCQT-94ET 40x90x29h 400V~2N 50/60 Hz 17,39 8 4 x 2,5 mm²
PCC-94ET 40x90x90h 400V~2N 50/60 Hz 14,78 6,8 4 x 1,5 mm²
PCCT-94ET 40x90x29h 400V~2N 50/60 Hz 14,78 6,8 4 x 1,5 mm²
PC-98ET 80x90x90h 400V~3N 50/60 Hz 30,43 14 5 x 4 mm²
PCT-98ET 80x90x29h 400V~3N 50/60 Hz 30,43 14 5 x 4 mm²
PCQ-98ET 80x90x90h 400V~3N 50/60 Hz 34,78 16 5 x 6 mm²
PCQT-98ET 80x90x29h 400V~3N 50/60 Hz 34,78 16 5 x 6 mm²
PCC-98ET 80x90x90h 400V~3N 50/60 Hz 29,57 13,6 5 x 4 mm²
PCCT-98ET 80x90x29h 400V~3N 50/60 Hz 29,57 13,6 5 x 4 mm²
PC-912ET 120x90x90h 400V~3N 50/60 Hz 30,43 21 5 x 4 mm²
PCT-912ET 120x90x29h 400V~3N 50/60 Hz 30,43 21 5 x 4 mm²
PCQ-912ET 120x90x90h 400V~3N 50/60 Hz 34,78 24 5 x 6 mm²
PCQT-912ET 120x90x29h 400V~3N 50/60 Hz 34,78 24 5 x 6 mm²
PC-916ET 160x90x90h 400V~3N 50/60 Hz 45,65 28 5 x 10 mm²
PCQ-916ET 120x90x90h 400V~3N 50/60 Hz 52,17 32 5 x 10 mm²
PCT-916ET 160x90x29h 400V~3N 50/60 Hz 45,65 28 5 x 10 mm²
PCQT-916ET 120x90x29h 400V~3N 50/60 Hz 52,17 32 5 x 10 mm²


GENERAL INFORMATION
Translation of the original instructions
19
Transformation
MODEL DIMENSIONS POWER SUPPLY MAXIMUM
POWER (kW)
MAXIMUM
ABSORPTION
(A)
POWER SUPPLY
CABLE
silicon type
PC-94ET 40x90x90h 230V~3 50/60 Hz 7 26,36 4 x 4 mm²
PCT-94ET 40x90x29h 230V~3 50/60 Hz 7 26,36 4 x 4 mm²
PC-94ET 40x90x90h 230V~ 50/60 Hz 7 30,43 3 x 4 mm²
PCT-94ET 40x90x29h 230V~ 50/60 Hz 7 30,43 3 x 4 mm²
PCQ-94ET 40x90x90h 230V~3 50/60 Hz 8 30,12 4 x 4 mm²
PCQT-94ET 40x90x29h 230V~3 50/60 Hz 8 30,12 4 x 4 mm²
PCQ-94ET 40x90x90h 230V~ 50/60 Hz 8 34,78 3 x 6 mm²
PCQT-94ET 40x90x29h 230V~ 50/60 Hz 8 34,78 3 x 6 mm²
PCC-94ET 40x90x90h 230V~3 50/60 Hz 6,8 25,6 4 x 4 mm²
PCCT-94ET 40x90x29h 230V~3 50/60 Hz 6,8 25,6 4 x 4 mm²
PCC-94ET 40x90x90h 230V~ 50/60 Hz 6,8 29,57 3 x 4 mm²
PCCT-94ET 40x90x29h 230V~ 50/60 Hz 6,8 29,57 3 x 4 mm²
PCC-98ET 80x90x90h 230V~3 50/60 Hz 13,6 39,11 4 x 6 mm²
PCCT-98ET 80x90x29h 230V~3 50/60 Hz 13,6 39,11 4 x 6 mm²

Technical data table - CF S90E
MODEL DIMENSION
SPOWER SUPPLY
MAXIMUM
ABSORPTION
(A)
MAXIMUM
POWER
(kW)
Emissivity
POWER SUPPLY
CABLE
silicon type
CF4-98ET 80x90x90h 400V~3N 50/60 Hz 37,83 20,7 / 5 x 6 mm²
CFQ4-98ET 80x90x90h 400V~3N 50/60 Hz 41,74 22,7 / 5 x 10 mm²
CFC4-98ET 80x90x90h 400V~3N 50/60 Hz 36,96 20,3 / 5 x 6 mm²
CF6-912ETV 120x90x90h 400V~3N 50/60 Hz 45,2 27,7 / 5 x 10 mm²
CFQ6-912ETV 120x90x90h 400V~3N 50/60 Hz 49,6 30,7 / 5 x 10 mm²
CF6-912ET 120x90x90h 400V~3N 50/60 Hz 45,2 30,2 / 5 x 10 mm²
CFQ6-912ET 120x90x90h 400V~3N 50/60 Hz 49,6 33,2 / 5 x 10 mm²
CF8-916ETV 160x90x90h 400V~3N 50/60 Hz 60,4
(30+30,4)
37,2
(16,2+21) / 5x4 mm² +5x4 mm²
CFQ8-916ETV 160x90x90h 400V~3N 50/60 Hz 67
(32,2+34,8)
41,2
(17,2+24) / 5x6 mm² +5x6 mm²
CF8-916ET 160x90x90h 400V~3N 50/60 Hz 60,4
(30+30,4)
41,4
(20,4+21) / 5x4 mm² +5x4 mm²
CFQ8-916ET 160x90x90h 400V~3N 50/60 Hz 67
(32,2+34,8)
45,4
(21,4+24) / 5 x 6 mm²
CFV4-98ET 80x90x90h 400V~3N 50/60 Hz 37,97 19,32 <70 5 x 6 mm²
CFVQ4-98ET 80x90x90h 400V~3N 50/60 Hz 42,32 21,32 <70 5 x 10 mm²
CFVC4-98ET 80x90x90h 400V~3N 50/60 Hz 37,1 18,92 <70 5 x 6 mm²
CFV6-912ETV 120x90x90h 400V~3N 50/60 Hz 38,49 26,32 <70 5 x 6 mm²
CFVQ6-912ETV 120x90x90h 400V~3N 50/60 Hz 42,84 29,32 <70 5 x 10 mm²


GENERAL INFORMATION
Translation of the original instructions
20
DESIGN ASSEMBLY/TRANSFORMATION ELECTRICAL LINKING TERMINAL BLOCK PERNIONS (see
technical data table)
·POWER SUPPLY CONNECTION

·HEATING ELEMENT CONNECTION
