Lovencare egg2 User manual

I
©B a b y S tyle UK Lt d, AJB082429062021v6 p age 1

© BabyStyle U K Ltd , AJB140508072021v 2
egg®
Instruction Manual.
IMPORTANT: Read the instructions carefully and keep for
future reference.
Contents
Contents/Parts check list.
Important safety information.
Product information.
Section 1 - Chassis
Fitting/removing the front wheels.
Fitting/removing the rear wheels.
Opening the chassis.
Operating the parking brake.
Operating the front swivel wheel.
Adjusting the handle height.
Folding the chassis.
Section 2 - Seat Unit
Fitting the seat unit to the chassis.
Fitting/removing the bumper bar.
Adjusting the seat unit.
Adjusting the calf support.
Fitting/removing the seat unit hood.
Fitting the seat unit apron.
Using the 5 point safety harness.
Hood/canopy ventilation windows.
Removing the seat unit from the chassis.
Fitting the rain cover.
Fitting the insect net.
Fitting the footmuff.
Fitting the seat liner.
2
Page
2-3
4
5
6
6
6 / 7
7
8
8
8 / 9
10
10 / 11
11
12
12
12
13
14
14
14
15
15
Parts:
Chassis
2x front wheels
2x rear wheels
Seat unit
Apron
Hood
Bumper bar
Rain cover
Insect net
Parts:
Carrycot body
Mattress
Liner
Apron
Rain cover
Contents cont ...
Section 3 - Carrycot
Assembling the carrycot.
Fitting the carrycot apron.
Adjusting the carrycot hood.
Fitting/removing the carrycot to the chassis.
Fitting the carrycot rain cover.
Fitting the carrycot insect net.
Section 4 - Car Seat Adaptors
Fitting the car seat adaptors.
Fitting the car seat.
Removing the car seat.
Removing the car seat adaptors.
Section 5 - Tandem Mode
Fitting/removing the tandem adaptors.
Fitting/removing tandem seat units.
Fitting/removing tandem carrycots.
Fitting/removing tandem car seat adaptors.
Fitting/removing tandem car seats.
Tandem Configurations.
Do not use tandem configurations.
Your egg Warranty.
Care and maintenance. How to look after your egg stroller.
Trouble Shooting.
Page
16
16
16
17
17
18
19
19
20
20
21
22
23
24
25
26 / 27
28
29
31
3
+
15
30

I egg_instruction_manual_ AJB 140 5 080 7 2021 v 2
egg®
Important Safety Information.
 
  
 
   

 
 













 




 

 


   
 

  
 






 
 

 

   

 


egg®
Product Information.
 
 
 

 
 






 

     

 8 

  


            
 
   

 
 



 


5
WARNING: TO AVOID INJURY OR DEATH

©B aby S tyle UK Ltd , A JB 1405080 7 2021v 2
 
egg®
Section 1 - Chassis
1. Fitting/removing the front wheels.
Press the quick release button on the back of
the wheel housing on the chassis and push the
front wheel onto axle.
The wheels are marked L for left and R for right
from the perspective of standing in front of the
chassis.
Important: Check the wheels are secure by
pulling downwards.
To remove; press the quick release button on
the back of the wheel housing on the chassis
and pull the wheel away from the axle.
2. Fitting/removing the rear wheels.
Press the button in the centre of the rear wheel
and push into the rear wheel housing.
Important: Check the wheels are secure by
pulling outwards.
To remove; press the button in the centre of the
rear wheel and pull the wheel away from the
wheel housing.
3. Opening the chassis.
Ensure the chassis is stood upright.
Push the chassis locking clip down to
release the front section of the chassis.
Allow the front of the chassis to move forwards.
You may have to pull forward
gently to assist this.
6
Release the stroller handle by pushing the
handle lock & gently lifting the handle.
Continue to lift the handle upwards until you
hear the lock engage with a click.
WARNING: Ensure the locking devices
are engaged before use.
4. Operating the parking brake.
Press down on the pedal to engage the
parking brake
Press down and release to disengage the
parking brake.
WARNING: Never leave the vehicle without
first fully engaging the parking brake.
 
egg®
7
 

©B abyStyle UK Ltd, AJB 1405080 7 2021v 2
egg
5. Operating the front swivel wheels.
Press the button until it clicks to switch
between fixed or swivel wheel trav el, one
button on the left, one button on the right.
6. Adjusting the handle height.
Rotate the central section of the handle forward
(1) and slide into the desired position (2).
Note: The handle has 5 height positions.
7. Folding the chassis.
Important: Remove the seat unit/carrycot/car seat
and any adaptors before attempting to fold
the chassis and ensure the shopping basket is
empty.
Important Note: The chassis will not fold unless the
handle is in the lowest position and the seat unit,
car seat or carrycot and any adaptors etc have
been removed from the chassis.
Engage the parking brake.
Ensure the handle is in its lowest position. Ensure
the front wheels are unlocked and in the swivel
position.
Fully rotate the central section of the handle
bar towards you, the hub locks will release and
the handle will freely move downwards, do not
force.
8
egg_instruction_manual_ AJB082429062021v6 Page 9
Lower the handle towards the floor and
push so that it locks with the latch on the left
hand side of the lower chassis.
Lift the carry handle, found in the centre of
the basket to allow the front of the chassis to
move towards the rear of the chassis.
Secure the chassis u sing the travel lock
at the front of the chassis; this will
engage automatically.
 
egg
9
 

©B abyStyle UK Ltd ,AJB 140 5 080 7 2021v 2
egg®
Section 2 - Seat Unit
1. Fitting the seat unit to the chassis.
Important: Ensure that both seat unit legs are in the same
position before attempting to fit the seat unit to
the chassis. Failure to do so may cause damage to
the seat unit.
Insert the seat unit legs into the main housings on the
chassis until the seat locks in place with a click.
WARNING: Ensure the seat unit is locked in place on both
sides of the chassis before use.
Note: The seat unit can be used in forward facing
or parent facing modes. Simply attach the seat unit in
the same way in your preferred facing mode.
2. Fitting the bumper bar.
Push the bumper bar ends into the corresponding
sockets on the seat unit whilst holding down the
release button.
Important: Ensure the bumper bar is locked in
place before use by firmly pulling the bumper bar
outwards.
10
3. Removing the bumper bar
Press the small buttons on the seat unit under
the bumper bar and pull the bumper bar away
from the seat unit.
Note: The bumper bar can be released one side
at a time to allow easy access for placing your
child in or removing your child from the seat unit.
4. Adjusting the seat unit.
Lift the adjustment handle lever on the top
side of the seat unit and rotate the seat to the
desired position. The seat unit will lock into
position when the handle is released.
Note: The seat unit has 3 preset positions.
egg®
+
11

©B abyStyle UK Ltd, A JB 140 5 080 7 2021v 2
egg®
5. Adjusting the calf support.
Pull the calf support upwards to raise.
Press-in both grey buttons at the side of the
footrest to lower into the desired position.
Note: The calf support has 4 positions.
6. Fitting/removing the seat unit hood.
Attach and fasten the zip; push the plastic clips
firmly onto the seat unit frame then close the clips. To
remove; unfasten the clips from the seat unit frame
and open the zip.
For a demonstration video on how to attach the
seat unit hood, please visit our FAQ section at
www.eggstroller.com
7. Fitting the seat unit apron.
Slide the bottom of the apron o ver the calf support. Pull
upwards into place and fold the apron flap o ver the
bumper bar. Secure using the press studs on the apron
flap.
12
8. Using the 5 point safety harness.
Fit together the two connectors on the harness straps
and push firmly into the buckle housing until they click
together.
Important: Ensure they are fully engaged before
use.
To release the connectors press in the grey button on the
buckle housing, the two connectors will release from the
main housing.
WARNING: To avoid serious injury always
use a 5 point safety harness. Important:
Always ensure the parking brake is engaged when
placing and removing children from the vehicle.
To alter the overall size of the harness, adjust the straps to
suit the child using the buckle sliders on the harness.
Harness shoulder height.
Adjusting harness the shoulder strap height. As your
child grows you will need to adjust the height of the
shoulder straps . Lift the panel at the back of the seat-
back and squeeze together the two plastic sliders. Move
up or down to adjust to the required position, this action
will automatically adjust the position of the head rest
cushion.
egg®
+
13

©B abyStyle UK Ltd, AJB 140 5 080 7 2021v 2
egg®
14
egg®
+
15
12. Fitting the insect net.
The insect net is located in a pocket on the underside of
the leg support. Remove the insect net (leaving the press
stud attached), pull up and over the extended stroller
hood. Not included with all strollers.
13. Fitting the footmuff (optional accessory).
Remove the comfort pads on the shoulder
straps and the crotch strap; unclip the shoulder
strap buckles and thread the straps and crotch
strap through the corresponding holes in the
footmuff. Re-fasten the buckles.
14. Fitting the seat liner (optional accessory).
Remove the harness pads and open the harness by un-
clipping the centre buckle and shoulder straps. Thread the
harness straps through the corresponding holes in the seat
liner and replace the harness pads.
9. Hood/Canopy ventilation windows
The hood/canopy of both the carrycot and the stroller
have ventilation windows panels. Use the finger/thumb
tab to fold back the textile panel to open the ventilation
window, reverse the action to close the panel.
10. Removing the seat unit from the chassis.
Press-in the grey buttons on the side of the seat unit and lift
the seat upwards from the chassis. Important: Always
remove your child from the seat unit before removing the
seat unit from the chassis.
11. Fitting the rain cover.
Slide the rain cover on from the footrest end first
ensuring it slides underneath the footrest. Pull up and
over the extended stroller hood and secure at the back
with the Velcro tabs.
WARNING: Never leave rain covers, hoods, aprons, sun
shades baby-nests or footmuffs on or over the stroller
indoors, in a hot atmosphere or near a heat source; your
child may overheat.

©B aby S tyle U K Ltd, AJB 140 5 080 7 2021v 2
egg®
Section 3 - Carrycot
1. Assembling the carrycot.
Remove the apron and mattress to gain access
to the stay bars in the bottom of the carrycot.
Using the tabs, pull the stay bars into the clips
on the baseboard until you hear them click into
place. Reposition the lining and place the
mattress back into the carrycot.
Important: Ensure that the stay bars are
fully engaged before using the carrycot.
2. Attaching the carrycot apron.
Fasten the zip of the apron to the zip on
the carrycot and pull all the way around.
3. Adjusting the carrycot hood.
Depress the buttons on the side of the hood
and pull up until you hear it click into place.
Depress the buttons again to put the hood
down. The carrycot hood has an intermediate
position (45 degrees) to allow viewing when the
carrycot is used in the tandem mode, lower
position.
16
4. Fitting the carrycot.
Lower the carrycot onto the chassis parent
facing. Insert the carrycot legs into the main
housings on the chassis and push down firmly
until it clicks and locks onto the chassis.
WARNING: Ensure the car rycot is locked in
place on the chassis before use.
5. Removing the carrycot.
Ensure the hood frame is erect and locked in
the perpendicular position. Hold the carrycot
by the handle at the top of the hood frame.
Use your other hand to lift the release lever at
the back of the carrycot as pictured opposite.
While the release lever is lifted pull directly up
on the carycot handle and lift the carrycot away
from the chassis.
6. Fitting the carrycot rain cover.
The carrycot hood must be fully extended
(erect) to support the rain cover. Place the
rain cover over the carrycot and fasten the
side panels (left and right) using the Velcro
tabs.
WARNING: Never leave rain covers,
hoods, aprons, sun shades baby-nests or
footmuffs on or over the stroller indoors, in
a hot atmosphere or near a heat source;
your child may overheat.
Never leave your child unattended.
egg®
+
17

© Baby S tyle U K Ltd, A J B140 5 080 7 2021v 2
egg®
7. Fitting the carrycot insect net.
Using the insect net from the seat unit which
is located in the pocket on the underside of
the leg support, place the insect net over the
carrycot with the hood extended and secure at
the sides using the elastic loops.
WARNING: The egg carrycot is suitable for a
child who cannot sit unaided, rollover or push
itself up on its hands and knees.
WARNING: Do not let other children play
unattended near the carrycot.
WARNING: Do not use if any part is broken,
torn or missing.
WARNING: Do not add another mattress on top
of the mattress provided.
WARNING: Never use the carrycot on a stand.
Do not leave your child unattended.
WARNING: Only use the carrycot on a
horizontal, firm, level anddry surface.
IMPORTANT:
• Regularly inspect the handle and base of the carrycot for signs of damage or wear .
Continue to use only if in good condition.
• There is restricted space when using the egg ride-on-board with the carrycot.
• Be aware of the risk of open fire and other strong heat sources such as electric fires, gas
fires etc in the vicinity of the carrycot.
• This carrycot is not a safe means of transport by car and should NEVER be used as such.
• The head of the child in the carrycot should never be lower than the body of the child.
• Before carrying or lifting, make sure that the handle is in the correct position for use.
18
Section 4 - Car Seat Adaptors
1. Fitting the car seat adaptors.
Insert the car seat adaptors onto the left and
right sides of the main chassis housings.
The adaptors are marked L for left and R for
right from the perspective of standing behind the
handle of the chassis. Press down firmly until they
click into place.
WARNING: Ensure the adaptors are securely
fitted before use by pulling them upwards.
2. Fitting the egg car seat parent facing only.
Align the car seat with the adaptors and lower
until it stops, fold back the handle to engage the
locks.
Other recommended car seats: Align the car seat
with the adaptors and lower until it stops push
down to engage the locks, there may be an
audible click.
WARNING: Ensure the car seat is securely
locked into place by gently pulling the car seat
upwards.
egg®
+
19
egg car seat locked in position.
egg car seat being lowered onto adaprors.