LRP electronic SXX Competition User manual

2. INSTALLATION TIPS
3. WIRES & INSTALLATION
6. SPARE- & OPTIONAL-PARTS
1. CONNECTIONS & EXPLANATIONS
USER MANUAL
ABC + -
C
B
A
• Positionthespeed-controlandcapacitorwheretheyareprotectedintheeventofacrashandgivesyoueasy
accesstotheconnectorsandbuttons.
• Mountthespeedoandcapacitorusingthesuppliedthick/blackdoubled-sidedtape
• Makesurethereisenoughclearancebetweenthespeed-control,power-wires,antenna andreceiver.Avoid
anydirectcontactbetweenpowercomponents,thereceiverortheantennaasthiscancauseinterference.If
interferenceoccurs,positionthecomponentsatadifferentplaceinthemodel.
• Theaerialshouldberunverticallyupandawayfromthereceiver.Avoidcontactwithanypartsmadeofcarbon
breormetal.Iftheaerialistoolong,don’tcoiluptheexcesslength.Seealsotheinstructionssuppliedwith
yourradiocontrolsystem.
•
Becauseofthephysicalprinciplesofbrushlesstechnology,thespeed-controlsdogetalittlehotterthenbrushed
systems.Thereforeitisrequiredtoletthespeed-controlcooldowncompletelyaftereveryrun.
RECEIVER CONNECTING WIRE:TheSXXisequipped
with an LRP Multicon receiver wire. As supplied, it
willeasilytinallordinaryreceivers.Makesureyou
connect it to receiver with correct polarity and use
channel2.
SENSOR CONNECTOR: located underneath the sol-
der tabs. The bi-directional multipole sensor wire
connects the speed-control and the motor. Always
usethesensorwireanddonotalterormodifythisca-
ble!Therearereplaceable/optionalhallsensorwires
available,pleaserefertocompleteline-upunderpoint
6„Spare-&Optional-Parts“.
POWER WIRES: Formaximumperformance,exible
silicone power wires without any connectors are
used.Theuniquesplittedsolder-tabsalloweasyand
convenient replacement of the power wires. Never-
thelesssomesolderingskillsarerequired.Avoidsol-
deringlongerthen5secpersolderingjointtoprevent
possibledamagetothespeed-controlduetooverhe-
atingof the components!Therearefull replacement
power wire sets available, please refer to complete
line-upunderpoint6„Spare-andOptionalParts“.
#80900 #80950 #80900 #80950
PureBrushlessCompetition yes B.E.C. 6.0V/3.0A
Forward/Brake yes C³Technology yes
Footprint 30.5x34.0mm X-Brake yes
Height 16.0mm 21.0mm HighFrequency yes
Weight(excl.wires) 30.0g 36.0g SensoredBrushlessSystem yes
VoltageInput 4.8-7.4V Multi-Protection-System yes
Typ.VoltageDrop*@20A 0.013V/phase 4,5,6celloptimised yes
RatedCurrent* 764A/phase Internal-Temp-CheckSystem2 yes
Compatiblewindingstyles Star LaunchControl yes
Rec.MotorLimitwith5cells over4.0T over2.5T BlueLED yes
Rec.MotorLimitwith6cells over4.5T over3.0T 4adj.Modes (AutoCellSystem,
ADPC2™Power Proles, Initial-
andAutomatic-Brake)
yesPowerWires 2.6mm² 3.3mm²
PluggedFan no yes
TheSXX‘s come suppliedwithexiblesiliconepower-wires(#80900=2.6mm²/#80950=3.3mm²)without
connectors.Beverycarefulwiththecorrectwiresequence/colorssinceanincorrectconnectionmaydamagethe
speed-control!Avoidcreatingsolderbridgesonthesolder-tabsandisolateallconnectionscarefully.
Caution:Avoidsolderinglongerthen5secpersolderingjointwhenreplacingthepowerwiresonthespeed-control
andmotortopreventpossibledamageduetooverheatingofthecomponents!
 •Connectthespeed-controltothereceiver(position:Channel2
 •Bluepower-wire  SpeedoMOT.Atomotor„A“
 •Yellowpower-wire  SpeedoMOT.Btomotor„B“
 •Orangepower-wire  SpeedoMOT.Ctomotor„C“
 •Connectthehallsensorcabletothespeed-control(underneaththesolder-tabs)andthemotor.
 •Doublecheckallconnectionsbeforeconnectingthespeed-controltoabattery.
CAUTION: Ifbatteryisconnectedwithreversedpolarityitwilldestroyyourspeed-control!
 •Redpower-wire  SpeedoBAT+tobattery„Plus“
 •Blackpower-wire  SpeedoBAT-tobattery„Minus“
 •Thespeed-controlisnowreadytobeset-up(seesection5).
RA00271
*Transistorsratingat25°CjunctiontemperatureSpecicationssubjecttochangewithoutnotice.
LRPelectronicGmbH
Wilhelm-Enssle-Str.132-134
73630Remshalden,Germany
[e-mail]-www.LRP.cc
DearCustomer,
thankyouforyourtrustinthisLRPproduct.BypurchasingaLRP SXX Competition / LRP SXX TC spec brushless
speed-control,youhavechosenoneofthemostadvancedandsuccessfulspeed-controlsoftoday.Thisspeed-
controlwithallofitshigh-techfeaturesandspeciallyselectedelectroniccomponentsisoneofthebestspeed-
controlscurrentlyavailableonthemarket.IFMARWorldChampion2008/2009!
 •PureBrushlessCompetitionSpeed-Control •Smallfootprint
 •C³(CopperCoreCooling)Technology •ADPC2™PowerProles
 •New„X-Brake“ •AutoCellSystem
 •Internal-Temp-CheckSystem2 •4,5,and6celloptimised
 •LaunchControl •SensoredDesign
Pleasereadthe following instructionscarefullybefore you startusing your speedcontrol. This user guide contains
importantnotesforthesafety,theuseandthemaintenanceofthisproduct.Thusprotectingyourselfandavoiddamages
oftheproduct.
Proceedaccordingtotheuserguideinordertounderstandyourspeedcontrolbetter.Pleasetakeyourtimeasyouwill
havemuchmorejoywithyourproductifyouknowitexactly.
Thisusermanualshallbekeptinasafeplace.Ifanothercustomerisusingthisproduct,thismanualhastobehanded
outtogetherwithit.
Receiverwire
On/Off-Switch
MOT.C(Orange)
PowerCapacitor
BAT+(Red) MOT.B(Yellow) BAT-(Black) MOT.A(Blue)
SensorConnector
(underneathsoldertabs)
InsetupmodetheSXX‘s storeseverystep(e.g.learningyourradiosneutralandendpoints)whenyoupresstheSET
button.AllthesettingswillbestoredintheSXX‘smemoryevenifitwillbedisconnectedfromthebattery.
Description othernamesinradio RequiredSetting
ThrottleTravel HighATV,EPA 100%
BrakeTravel LowATV,EPA,ATL 100%
ThrottleExponential EXP,EXPO startwith0
NeutralTrim SUBTrim centre
ServoReverse ThrottleReverse anysetting,don‘tchangeafterset-upprocedure!
TRANSMITTER SETTINGS
Setupthefollowingbasicfunctionsonyourtransmitter(ifavailable):
Ifyourtransmitterdoesn‘tofferanyofabovefunctions,it‘salreadyin„basicsetup“mode.
•Ensurethatthespeed-controlisnotconnectedtothedrivebatteryandisswitchedoff.
•Removemotorpinionorensurethatthewheelsofthemodelarefreetorotate.
•Switchthetransmitteronandsetthetransmitterthrottlesticktoneutral.
•Connectthespeed-controltothebatteryandswitchtheuniton.
•HoldtheSETbuttonpressedforatleast3sec.
YouenteredsetupmodeandtheSETLEDashesblue(itwillashuntilthesetupiscompleted).
•LeavetransmitterinneutralpositionandpresstheSETbuttononce.
Neutralsettingisstored,MODELEDashesyellowandthemotorbeeps.
•HoldfullthrottleontransmitterandpresstheSETbuttononce.
Full-throttlesettingisstored,MODELEDashesred.
•HoldfullbrakeontransmitterandpresstheSETbuttononce.
Brakesettingisstored,LED‘sglowred(MODE)andblue(SET).
• ThiscompletesthesetupprocedureandyourSX X isreadytouse.
• Ifyoumakeamistakeduringthesetupprocedure,don‘tworry:Disconnectthebatteryforabout10secandstart
againfromtherststep.
• Attheendofeachrunswitchofthecar,andthenswitchoffthetransmitter.
• Atthestartofeachrunswitchonthetransmitterrst,thenswitchonthecar.
• Forstorageofthecar,disconnectthedrivebatteryatanytime!
FUNCTION STATUS MODE LED SET LED
Neutral(automaticbrakeinactive) -- off blue
Neutral(automaticbrakeactive) -- red off
Forward partialthrottle yellow off
Forward fullthrottle yellow blue
Brake partialbrake red off
Brake fullbrake red blue
CHECKING THE FUNCTIONS:
ChecktheLED‘swhenmovingyourthrottlestickandyouwillseeifeverythingissetupcorrectly.
LRPoffersacomprehensivelineofaccessories,aswellasparticularspare-andoptionalitems.Hereyoundan
overview,forafullpicturepleasevisitourwebsiteatwww.lrp.cc:
Spare parts:
#81910 Sensor-Wire200mm
#82505 Power-WireSetBrushless2.6mm²(red,black,blue,orange,yellow)
#82506 Power-WireSetBrushless3.3mm²(red,black,blue,orange,yellow)
#82511 LowProlecoolingfan(onlyfor80950speedo)
Optional parts:
#819307 Sensor-Wire„HighFlex“70mm
#819310 Sensor-Wire„HighFlex“100mm
#819315 Sensor-Wire„HighFlex“150mm
#819320 Sensor-Wire„HighFlex“200mm
#81907 3.3mm²Powerwireblack(1.0m)
#81908 3.3mm²Powerwireblue(1.0m)
4. SPECIFICATIONS
5. RADIO- / SPEED-CONTROL SETUP
© LRP electronic GmbH 2009
HEATSINK: Toachievebestperfomanceevenunderextremeconditions,theheatsinkhasbeendirectlymountedto
thespeed-control.Thisensuresthebestpossibleheattransferawayfromthespeed-control.
Caution:NeverattempttoremovetheheatsinkoryourSXXmaygetdamagedifyoutrytodothis.Theheatsinkis
anintegralpart,gluedtothefet‘sandthereforecannotberemoved.
PLUGGED FAN(SXXTCspec#80950only!):yourspeed-controlcontainsahigh-performancelow-prole(25x25x-
7mm)fanandblueanodisedaluminiumscrews.thefancanbemountedontopoftheheatsinkandshouldbeused
fortoughapplicationsinhotconditionssuchasTCModiedor4wdOffRoad.Asaguidelinewerecommendusing
thefanwithmotorslowerthen5.0T.Thefanget‘s pluggedinto the 3-pinconnectoronthefrontandthereis a
replacementfansetavailable,pleaserefertocompleteline-upunderpoint6„Spare-andOptionalParts“.
OnSXXCompetition(#80900)versionyoucanalsoconnecttheoptionalfantothesame„port“ifneeded.
HallSensorWire
orange
blue
yellow
FanConnector
ORDER.NO.::
80900
80950
Brushless Competition speed-control
IFMAR World Champion 2008/2009
#80900: >4.0T Motorlimit
#80950: >2.5T Motorlimit

7. MODE PROGRAMMING 9. SPECIAL FEATURES
REPAIR PROCEDURES / LIMITED WARRANTY
8. TROUBLESHOOTING GUIDE
TheSXX features4modeswhichenableyoutoadjustit100%toYOURspecialrequirements.Thefactorysettings
areshowningreycolour.
MODE.1 (AutoCell System): werecommendusingvalue#2for4-6cellsNiMHracingpurposes,whichdis-
engagestheLiPoprotection.
MODE LED #1 #2
Yellow LiPo/NiMH
Automatic
4-6cellNiMH
RacingMode
Caution:thebyfarmostcommonreasonforfalseshutdownsisusingthewrongvalueinthismode!
MODE.2 (ADPC2™ Power Profiles): allowsyoutoadjusttheSXX toyourlikes.EitheryourunOnRoador
OffRoad,onslipperyorhigh-tractionsurfaces,wehaveincorporatedaproleforyou!Highervaluemeansmore
overallpowerandmoreaggressivethrottleresponse.
MODE.3 (Initial Brake): Allowsyoutosetacertainlevelof„hand-brake-effect“,whichisespeciallyuseful
forOffRoadracing.
MODE.4 (Automatic Brake):allowsyoutosetaslightbrakingactionwhichisappliedintheneutralrange.
Thisenablesyoutosimulatethefeelofabrushedmotorandalsoholdthethrottleonlongerwhenenteringaturn.
Forbrushlessmotorsyouachievethesamenaturalslowdownasabrushedmotorwithnoautobrakewhenyou
setvalue1-2.
• Howtogetinto„programmingthemodes“ PressMODEbuttonfor3ormoreseconds.
• Howtocheckthestoredvalues CountthenumberofashesoftheblueSET-LED
(*=value1|**=value2|etc.).
• Howtochangethevalue PressSETbuttontoincreasevaluebyonestep.
• HowtogettothenextMode PressMODEbuttononce.
• Howtoleavetheprogrammingmode IfyouareinMODE.4,presstheMODEbuttononemore
   time,whichwillalsostorethesettings!
Important:donotturntheswitchoffbeforeleavingMode4(byonemorepressofMODEbutton)asotherwiseyour
recentchangeswon‘tbestoredinthememoryoftheSXX!
Tableofsettings,valuesandmodes:seebelow(grey-shadedvaluesshow„worksdefaultsettings“)
MODE LED #0 #1 #2 #3 #4 #5 #6 #7 #8 #9 #10
Yellow/Red
(sametime) none Goingfromlowesttohighestautomaticbrakesetting (value1=minimum/value10=maximum)
ADPC2™ Power Profiles: AdvancedDigitalPhaseControlresultsinmorepowerandbetterdriveability.De-
pendingonthestatusofthecar(start,acceleration,fullspeed)thesoftwarecalculatestheperfectmotormanage-
mentbyadjustingcurrentlimiter,motortiming,throttlecurveandmore!Highervaluemeansmoreoverallpower
andaggressiveresponse.
Caution:Dorunlowestmechanicaltimingsettingonthemotorwhenusinghigh(>4)ADPC2proles!
Team advise: thesearetheLRPfactorydriverspreferedproles foreachracing class,which theyvaryslightly
dependingontrack,usedmotorandpersonalpreference!
C³ Technology (Copper Core Cooling):anotherrst,achievedbyLRP!TherevolutionaryC³Technologyfor
lowestrunningtemperatures,aspecialcoppercorebondsthebottomsidefetstotheheatsinkforevencoolingof
allfet‘swhichresultsinhigherpowertowardstheendoftherunandalowermotorlimit.
Pure Brushless Forward/Brake Design: uncompromisingandoutstandingperformancefortoplevelcom-
petitionwasthetargetfortheSXX!ThereforetheLRPengineeringteamdevelopedapureforward/brakebrushless
competitionspeed-control.Thereisnoreversefunctionandnobrushedoperation.
Internal-Temp-Check System 2: allowsyoutoread-outthemaximuminternaltemperaturethatthespeedo
reached.Youcanconvienentlyread-outthetemperaturebackinthepitssinceitremainsstoreduntilyouturnit
onthenexttimeregularly(whichwillresetthememory).Thisnewfeatureallowsyoutoaccuratelycheckifallis
runningwellorifyou‘reclosetoshutdownalready.
How to read-out the temperature:
 Switchat„OFF“position.
 KeepMODEbuttonpressedwhileyouturnswitchto„ON“(thenreleasebutton)
 SETLEDwillstarttoashblue(MODELED‘sareoff),nowcountthenumberofashes.
 Thehigherthenumberofashes,thehotterthespeedoran,shutdownwilloccurat10ashes.
 Everyashbelow10equalsto5°Ctemperaturedecrease.
AutoCell System:Readyforthenextbatterytechnology–LiPobatteries!LRP’sexclusiveandsmartAutoCell
Systemensuresthat LiPobatteriescanbeused safelywithoutaccidentiallydeep-dischargingofthecells.The
motorfunctionwillbeshut-offandtheSETLEDwillashifthesystemrecognisesverylowbatteryvoltage.
Caution:thefactorydefaultis#1,whichis„LiPomode“!Makesureyouchangeto#2whenrunningNiMHbat-
terieswith4or5cells.
X-Brake: thebestgotperfectedfurther!Asuperlinearfeelingwithanevenstrongerpushbrakeand10nesteps
foralmostinniteadjustmentsofinitial-andautobrake!
Team advise: Agoodstartingpointforthebrakesettingonyourradiois80%forallclasses.Makesureyoudothe
radio-setupwithallsettingsontheradioon100%!
Changing Mode settings without the transmitter: Atraceeventsyouusuallydonothaveaccesstoyour
transmitter,butnevermindsinceyoucansimplydisconnectthereceiverleadfromthereceiverandchangethe
MODEsettingsasdescribedinsection6„ModeProgramming“.
Launch Control: thelaunchcontrolallows„rocketlike“starts.Afteractivationitgivesyoumorepoweronetime
forthestart(thisfeatureisonlyrecommendedtobeusedwithtouringcarsonhightractionsurfaces!).
Howto activate launch control:
 Holdtriggeronradioatfullbrakefor5secbeforestart.Readyandactive!!!
Works-Default-Settings: All LRP speed -controls come factory-adjusted (def aults are grey-shaded above).
If you loose trackof the modes,youcanrestoretheworks default settings. With thetransmitterswitchedon,
holdtheSETbuttonpressedwhileyouswitchonthespeed-control.ThisreturnstheunittotheLRPworksdefault
settings.
Power Capacitor: Neverdisconnectthepower-capacitor!Itoffersincreasedpunchandadditionalprotection,
itmustbeconnectedtoBAT+andBAT-solderpadswithshortestpossiblewires.
IceDrive Design:LRP’ssecretIceDriveDesignresultsinlowerspeedotemperatureunderallracingconditions.
Sorry,nofurtherdetailstobedisclosed.Simplyastepaheadofthecompetition!
Sensored Brushless Technology: AdvancedDigitalallowstheperfectknowledgeofthebrushlessmotor’s
magnetposition.ThisresultsinperfectmotorcontrolathighandlowRPM‘s,aswellasperfectbrakecontrol.
Multi-Protection System, 3-way protection: Theperfectprotectionagainstshort-circuits(motor),over-
loadandoverheating.Ifyourspeed-controlfacesoverload,themotorfunctionwillbeshut-offforprotectionandthe
SETLEDwillash,althoughthesteeringfunctionismaintained.Letthespeed-controlcooldownforafewminutes.
Ifyouexperiencefrequentshutdowns,checkforthefollowing:
•SettingforAutoCellSystem(bymistakeinLiPomodewhenusingNiMHbatteries?)
•Correctgearratio(refertomotormanualforgearingrecommendations)
•ADPC2settingtoohigh(highervaluewillheatupmotorandspeed-controlexcessively)
•Motoristoostrongormotorisdamaged.
SyMPTOM CAUSE REMEDy
Servoisworking,nomotor
function. Speed-controlpluggedinincorrectly Plugspeed-controlinCh2
Overloadprotectionactivated Allowspeed-controltocooldown
Wiringproblem Checkwiresandconnectors
SensorWiremissing/defective Install/replacesensorwire
Motordefective Replacemotor
Speed-controldefective Sendinproductforrepair
Noservoandnomotorfunction. Speedoconnectedtoreceiverwithwrong
polarity Connectspeedowithcorrectpolarity
Wiringproblem Checkwiresandconnectors
Batterydefective Replacewithdifferentbatterypack
Crystaldefective Replacecomponentsonebyone.
Receiverdefective
Transmitterdefective
Speed-controldefective Sendinproductforrepair
Motorstutterswhileacce-
lerating SensorWiredefective ReplaceSensorWire
MotororSensorBoardinmotordefective Replacesensorboardormotor
Radiointerference Changelocationofcomponents
PowerCapacitordamaged ReplacePowerCapacitor
Speed-controldefective Sendinproductforrepair
Motorrunsinreversewhen
acceleratingforwardonthe
transmitter.
Modelwithreversedgearbox! Cannotuseasensoredbrushlesssystem!
Insufcientperformance.
E.g.poorbrakepower,topspeed
oracceleration..
Motorpiniontoobigorgearratiotoolong. Usesmallermotorpinion/shortergearratio
Transmittersettingschangedafterset-up Repeatset-upprocedure
PowerCapacitordamaged ReplacePowerCapacitor
Motororsensor-boardinmotordefective Replacesensor-boardormotor
Speed-controldefective. Sendinproductforrepair
Speed-controlswitchesoff
frequently. RunninginLiPomodewhenusingNiMH battery! ChangevalueofAutocellSystemto#2
Fannotconnectedordamaged Check/attachfan
Modelusedtoooftenwithoutcool-down
periods Letspeed-controlcooldownaftereveryrun
Motorstrongerthanmotorlimitorinputvoltage
toohigh Useonlymotorsandbatterieswhicharewithin thespecicationsofthespeed-control
Motorpiniontoobig(e.g.gearratiotoolong) Usesmallermotorpinion/shortergearratio
Stuckdrivetrainorball-bearing Maintainmodel
Motordefective Replacemotor
Motorneverstops,runsat
constantslowspeed Transmittersettingschangedafterset-up Repeatset-upprocedure
Humidity/waterinspeed-control Immediatelyunpluganddryspeed-control
MotororSensorBoardinmotordefective Replacesensorboardormotor
Radiointerference Receiverorantennatooclosetopowerwires,
motor,batteryorspeed-control.
Receiveraerialtooshortorcoiledup
See„InstallationTips“and„Installation“
Receiverdefective,toosensitive;
Transmitterdefective,transmitteroutput
powertoolow,servoproblem
Replacecomponentsonebyone
Onlyuseoriginalmanufacturerscrystals
Poorbatteryconnection Checkplugsandconnectingwires
Transmitterbatteriesempty Replace/rechargetransmitterbatteries
MODE LED #0 #1 #2 #3 #4 #5 #6 #7 #8 #9 #10
Yellow/Red
(alternate) none Goingfromlowesttohighestinitialbrakesetting (value1=minimum/value10=maximum)
MODE LED Remark #1 #2 #3 #4 #5 #6 #7 #8 #9 #10
Red
Limiter low medium high off off off off off off off
Throttle -expo -expo -expo -expo -expo -expo linear linear +expo +expo
Timinglevel 1111233445
CLASS Touring Car 2wd Off-Road 4wd Off-Road Truck Off-Road 1/12th
ADPC2 Profile 4-6 1-3 2-4 2-4 2-5
#1 #2 #3 #4 #5 #6 #7 #8 #9 #10
>-45°C
>-81°F
-40°C
-72°F
-35°C
-63°F
-30°C
-54°F
-25°C
-45°F
-20°C
-36°F
-15°C
-27°F
-10°C
-18°F
-5°C
-9°F
Shut-
down
AllproductsfromLRPelectronicGmbH(hereinaftercalled“LRP”)aremanufacturedaccordingtothehighestqua-
litystandards.LRPguaranteesthisproducttobefreefromdefectsinmaterialsorworkmanshipfor90days(non-
europeancountrisonly)fromtheoriginaldateofpurchaseveriedbysalesreceipt.Thislimitedwarrantydoesn’t
coverdefects,whicharearesultofmisuse,impropermaintenance,outsideinterferenceormechanicaldamage.
„Thisappliesamongotherthingson:
• Cutofforiginalpowerplugornotusingreversepolarityprotectedplugs
• Receiverwireand/orswitchwiredamaged
• Mechanicaldamageofthecase
• Humidity/Waterinsidethespeedcontrol
• Mechanicaldamageofelectronicalcomponents/PCB
• SolderedonthePCB(exceptonsolderpads)
• Connectedspeed-controlwithreversedpolarity“
Toeliminateallotherpossibilitiesor improper handling,rstcheck allother componentsin yourmodelandthe
troubleshootingguide,ifavailable,beforeyousendinthisproductforrepair.Ifproductsaresentinforrepair,which
dooperateperfectly,wehavetochargeaservicefeeaccordingtoourpricelist.
Withsendinginthisproduct,thecustomerhastoadviseLRPiftheproductshouldberepairedineithercase.If
thereisneitherawarrantynorguaranteeclaim,theinspectionoftheproductandtherepairs,ifnecessary,ineither
casewillbechargedwithafeeatthecustomersexpenseaccordingtoourpricelist.Aproofofpurchaseincluding
dateofpurchaseneedstobeincluded.Otherwise,nowarrantycanbegranted.Forquickrepair-andreturnservice,
addyouraddressanddetaileddescriptionofthemalfunction.
IfLRPnolongermanufacturesareturneddefectiveproductandweareunabletoserviceit,weshallprovideyou
withaproductthathasatleastthesamevaluefromoneofthesuccessorseries.
Thespecicationslikeweight,sizeandothersshouldbeseenasguidevalues.Duetoongoingtechnicalimpro-
vements,whicharedoneintheinterestoftheproduct,LRPdoesnottakeanyresponsibilityfortheaccuracyof
thesespecs.
LRP-Distributor-Service:
• Packageyourproductcarefullyandincludesalesreceiptanddetaileddescriptionofmalfunction.
• SendparceltoyournationalLRPdistributor.
• Distributorrepairsorexchangestheproduct.
• ShipmentbacktoyouusuallybyCOD(cashondelivery),butthisissubjecttoyournationalLRPdistributor‘s
generalpolicy.
Toeliminateallotherpossibilitiesor improper handling,rstcheck allother componentsin yourmodelandthe
troubleshootingguidebeforeyousendinthisproductforrepair.Ifproductsaresentinforrepair,whichdooperate
perfectly,wehavetochargeaservicefeeaccordingtoourpricelist.
The crossed-outwheeledbin meansthat within theEuropean Union theproductmust betaken
to seperate collection at the product end-of-life. Do not dispose of these products as unsor ted
municipalwaste.