Programmable Logic Controller Installation Guide
XGT FEnet XGL-EFMTB/FB/HB
This installationguide provides simple function informationor PLC control.Please readcarefully
this data sheet and manuals before using products. Especially read precautions then handle
the products properly.
■ Meaning of warning and caution label
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices
①Do not contact the terminals while the power is applied.
②Be sure there are no foreign metallic matters.
Do not manipulate the battery(charge, disassemble, hitting, short, soldering).
①Be sure to check the rated voltage and terminal arrangement before wiring
②When wiring, tighten the screw of terminal block with the specified torque range
③Do not install the flammable things on surroundings
④Do not use the PLC in the environment of direct vibration
⑤Except expert service staff, do not disassemble or fix or modify the product
⑥Use the PLC in an environment that meets the general specifications contained
in this datasheet.
⑦Be sure that external load does not exceed the rating of output module.
⑧When disposing of PLC and battery, treat it as industrial waste.
⑨I/O signal or communication line shall be wired at least 100mm away from
high-voltage cable or power line.
■To install, observe the below conditions.
℃
℃
5 ~ 95%RH, non-condensing
5 ~ 95%RH, non-condensing
5 Vibration
Resistance
IEC 61131-2
each
direction
for
X, Y, Z
■ For system configuration, the following version is necessary.
1) XGI CPU : V4.06 or above
2) XGK CPU : V4.55 or above
3) XGR CPU : V2.72 or above
4) XG5000 Software : V4.30 or above
■Cable is recommended for S-FTP over CAT5E. Cable types vary Depending on your system
configuration and environment. Please consult a professional supplier before installation.
1) Electrical Characteristic
Insulation resistance(Min)
Ω
±
Attenuation dB/100m
Or less
Near-end crosstalk
Attenuation dB/100m
Or less
■This is front part of the Module. Refer to each name when operating the system. For more
information, refer to user’s manual
■ LED details
Silk
On during HS Link service
P2P
On during P2P Link
service
- P2P Link service is off
ERR
ON when a fatal error
occurs
- Normal
On during server operation
Network link disconnection
■ Here describes the method to attach each module to the base or remove it.
1) Attachment of module
①Insert a fixed projection of the lower part
Of PLC into the module fixed hole of base
②Slide the upper part of module to fix
to the base, and then fit it to the base
by using the module fixed screw.
②Pull the upper part of module to check
if it is installed to the base completely.
2) Detachment of module
①Loosen the fixed screws of the upper
part of module from the base
②By pressing the hook, pull the upper part of
module from the axis of the lower part of module
③By lifting the module upward, remove
the loading lever of module from
the fixing hole
■Installation of cable
1) 10/100/10000BASE-TX’s max.extended length between nodes is 100m.
2) This module provides Auto Cross Over function so the user can use both cross and direct
cable.
■ Caution
1) Exceeding load makes problems shown below.
- XGL-EFMTB/FB/HB (5,000packet/sec)
2) Please note the switching loop when using Ethernet switch.
■ Warranty period
18 months after the production date.
■ Scope of Warranty
18 month warranty is available except:
1) The troubles caused by improper condition, environment or treatment except the
instructions of LS ELECTRIC.
2) The troubles caused by external devices
3) The troubles caused by remodeling or repairing based on the user’s own discretion.
4) The troubles caused by improper usage of the product
5) The troubles caused by thereason which exceeded theexpectation from science and
technology level when LS ELECTRIC manufactured the product
6) The troubles caused by natural disaster
■ Change in specifications
Product specifications are subject to change without notice due to continuous product
development and improvement.
LS ELECTRIC Co., Ltd. www.lselectric.co.kr 10310000496 V4.6 (2020.4)
•E-mail: automation@lselectric.co.kr
•Headquarter/Seoul Office
Tel: 82-2-2034-4033,4888,4703
•LS ELECTRIC Shanghai Office (China)
•LS ELECTRIC (Wuxi) Co., Ltd. (Wuxi, China)
•LS-ELECTRIC Vietnam Co., Ltd. (Hanoi, Vietnam)
•LS ELECTRIC Middle East FZE (Dubai, U.A.E.)
•LS ELECTRIC Europe B.V. (Hoofddorf, Netherlands)
•LS ELECTRIC Japan Co., Ltd. (Tokyo, Japan)
•LS ELECTRIC America Inc. (Chicago, USA)
•Factory: 56, Samseong 4-gil, Mokcheon-eup, Dongnam-gu, Cheonan-si, Chungcheongnam-
do, 31226, Korea
Parts Name and Dimension (mm)
Pin No. Sign
0496
