Ltech 2272700 User manual

1. Product Parameter:
1
LT-858-5A
2. Product Size:
LT-858-5A
DMX-PWM CV DECODER
LT-858-5A DMX-PWM decoder works to convert universal DMX512 digital signal to PWM signal, which
controlled by DMX512 console. It can realize 0-100% brightness and various changing effect. And can
control single color, two color, RGB RGBA, RGBW LED lights. ,
LT-858 5A DMX-PWM CV Decoder-
Input Signal: DMX512
Input Voltage: 12~24Vdc
Output Voltage: 12~24Vdc
DMX512 Socket: RJ45
Product Size: L175×W42×H33(mm)
Package Size: L183×W48×H41(mm)
Weight(G.W.): 310g
Working Temperature: -30 ~65℃ ℃
Max. Current Load: 5A×4CH Max. 20A
Max. Output Power: 0-240W...480W
3. Configuration Diagram:
LT-858 5A DMX-PWM CV Decoder-
FUN=ON (the 10th ) dip switch=ON Self-testing Mode
FUN=OFF (the 10th ) Modedip switch=OFF DMX
Dip Switch Operation:
4.
FUN=OFF (the 10th dip switch ) Mode=OFF DMX
4.1 How to set DMX address via dip switch:
E.g.1: Set Initial Address To 32. E.g.2: Set Initial Address To 37. E.g.3: Set Initial Address To 178.
4.2 Self-testing Mode:
DMX address value = the total value of (1-9), to get the place value when in “on” position,
otherwise will be 0.
2
FUN=ON (the 10th ) dip switch=ON Self-testing Mode
1=ON 4=ON 7=ON 8=ON 9=ON2=ON 5=ON 3=ON 6=ON
Self-testing
Function
1-9=OFF
Dip Switch
Static
Black
Static
Red
Static
Red
Static
Green
Static
Green
Static
Blue
Static
Blue
Static
Yellow
Static
Yellow
Static
Purple
Static
Purple
Static
Cyan
Static
Cyan
Static
White
Static
White
7 Colors
Jumping
7 Colors
Jumping
7 Colors
Smooth
7 Colors
Smooth
OFF
ON
[Attn] When several dip switches are ON, subjected to the highest switch value.
As the figure above shows, the effect will be 7 colors smooth at 7 speed level.
For changing effects (Dip Switch 8 9=ON): /
DIP switch 1-7 is used to realize 7 speed levels.
(7=ON, the fastest level)
www.ltech-led.com

LT-858 5A DMX-PWM CV Decoder-
3
5. Wiring Diagram:
4
6. Attention:
7. Warranty Agreement:
6.1 The product shall be installed and serviced by the qualified person.
6.2 This product is non-waterproof. Please avoid the sun and rain. When installed outdoors please ensure
it is mounted in a water proof enclosure.
6.3 Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
6.4 Please check if the output voltage of the LED power supply used comply with the working voltage of
the product.
6.5 Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current.
Please also ensure that the cable is secured tightly in the connector.
6.6 Ensure all wire connections and polarities are correct before applying power to avoid any damages to
the LED lights.
6.7 If a fault occurs, please return the product to your supplier. Do not attempt to fix this product by yourself.
7.1 We provide lifelong technical assistance with this product:
A 5-year warranty is given from the date of purchase. The warranty is for free repair or replacement
and cover manufacturing faults only.
For faults beyond the 5-year warranty, we reserve the right to charge for time and parts.
7.2 Warranty exclusions below:
Any man-made damages caused from improper operation, or connecting to excess voltage and
overloading.
The product appears to have excessive physical damage.
Damage due to natural disasters and force majeure.
Warranty label, fragile label and unique barcode label have been damaged.
The product has been replaced by a brand new product.
7.3
7.4 Any amendment or adjustment to this warranty must be approved in writing by our company only.
★ This manual only applies to this model. reserve the right to make changes without We prior notice.
Update Time: 2016.10.18
Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
We shall not be liable for any incidental or consequential damages for breach of any stipulation
in this warranty.
LT-858 5A DMX-PWM CV Decoder-
www.ltech-led.com
*
An amplifier is needed when more than 32 decoders are connected, signal amplification should not be more than
5 times continuously.
*
terminal resistor at the end of each line.
If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W 90-120Ω