LTS LTD9116MKIT User manual

UserManual
LTD9116MKIT User Manual
Contact US:
LTS Products
LT Security, Inc.
19455 E. Walnut Drive North
Walnut, CA 91789
Website:
http://www.LTSecurityinc.com
Tech Support:
Toll Free：888-587-5871
Email：[email protected]
0

UserManual
1
Contents
Chapter 1: DVR Features........................................................................................................................................3
DVR Feature ......................................................................................................................................................3
Chapter 2: Overview................................................................................................................................................3
2.1 Front Panel ...................................................................................................................................................3
2.2 Rear Panel ....................................................................................................................................................4
2.3 Remote Control ............................................................................................................................................4
Chapter 3: Installation.............................................................................................................................................5
3.1 Install Hard Disk ..........................................................................................................................................5
3.2 Connecting Camera and Monitor .................................................................................................................5
3.3 VGA Output .................................................................................................................................................5
3.4 Connecting Power Supply............................................................................................................................5
Chapter 4: Starting the DVR...................................................................................................................................5
4.1 Firmware Version .........................................................................................................................................5
4.2 Detecting Installed Hard Drive.....................................................................................................................6
4.3 Format Hard Drive .......................................................................................................................................6
Chapter 5: DVR Menu System................................................................................................................................6
5.1 Navigating the Menus ..................................................................................................................................6
5.2 Menu Overview............................................................................................................................................7
5.3 Camera Setup ...............................................................................................................................................7
5.4 Record Setup ................................................................................................................................................7
5.5 Record Frame Rate.......................................................................................................................................8
5.6 Video Quality ...............................................................................................................................................8
5.7 Record Schedule...........................................................................................................................................8
5.8 Sensor Setup.................................................................................................................................................9
5.9 H/W Sensor Setup ........................................................................................................................................9
5.10 Motion Detector Setup .............................................................................................................................10
5.11 Hard Drive Setup......................................................................................................................................10
5.12 Miscellaneous Setup - Change Password .................................................................................................11
5.13 Miscellaneous Setup - Set Time ...............................................................................................................11
5.14 Miscellaneous Setup - Hidden Channel ...................................................................................................12
5.15 Miscellaneous Setup - Audio Port Setup ..................................................................................................12
5.16 Miscellaneous Setup - PTZ Setup ............................................................................................................12
5.17 Miscellaneous Setup - Image Parameters.................................................................................................13
5.18 Miscellaneous Setup - Password Enable ..................................................................................................13
5.19 Miscellaneous Setup - Keypad Tones.......................................................................................................14
5.20 Miscellaneous Setup – SEQ.Dwell Time .................................................................................................14
5.21 Miscellaneous Setup - VGA Setup ...........................................................................................................14
5.22 Network Setup..........................................................................................................................................14
5.23 Language ..................................................................................................................................................18
5.24 Reset Menu...............................................................................................................................................18
5.25 NTSC/PAL Output select .........................................................................................................................18
Chapter 6: Record..................................................................................................................................................19
6.1 Start Recording...........................................................................................................................................19

UserManual
2
6.2 Audio Recording ........................................................................................................................................19
6.3 Stop Recording...........................................................................................................................................20
6.4 Estimated Recording Length......................................................................................................................20
Chapter 7: Playback...............................................................................................................................................20
Chapter 8: USB Progamming................................................................................................................................21
8.1Driver Installation: ......................................................................................................................................21
8.2 Program Interface.......................................................................................................................................21
8.3 Program Running .......................................................................................................................................22
Chapter 9: Specification ........................................................................................................................................25
9.1 DVR ...........................................................................................................................................................25
9.2 CAMERAS.................................................................................................................................................25
Chapter 10:Appendix............................................................................................................................................26
10.1 System connect sketch map......................................................................................................................26
10.2 Accessories Included With DVR..........................................................................................................26

UserManual
Chapter 1: DVR Features
DVR Feature
MPEG-4 compression
9 BNC Camera Inputs - 1 BNC Video Output
1 Audio Input -1 Audio Output
System Format : NTSC /PAL
Motion Detection with Sensitivity and Area Settings
Time Schedule, Alarm and Motion Triggered Recording Modes
Hard Disk Support up to 500GB
Supports PTZ Control via RS-485 Port
View and Operate over Network (Broadband Connection Required)
Built-in USB 2.0 Port for Backup to Computer
VGA Output
Chapter 2: Overview
2.1 Front Panel
1.Power LED 11. IR receiver
2. HDD LED 12.REW: rewind
3.Search 13.PAUSE
4. MUTE: turn on/off audio output 14.PLAY
5. CH-: view previous channel 15.FWD: forward
6.CH+: view next channel 16.STOP
7.ALL: view all channels 17.REC: record
8. MENU/ESC/LEFT 18.DOWN
9. UP 19.PTZ:enter PTZ mode
10. SEL/EDIT/RIGHT
3

UserManual
2.2 Rear Panel
1. Audio Input
2. Video output
3. CH1-CH9:video input 1- video input 9 9.DC Power Input Jack
4. VGA output
5.USBport
6. LAN: Ethernet port
7. Audio output
8.RS-485/Sensor/Alarm
10.Power switch
11. Grounding
2.3 Remote Control
4
1-9 Channel Select 1-9
0 Number
ALL Display all Channels
Menu Enter or Exit Menu
▲Move Up
▼Move Down
◄/ ►Left/ Right
SEL Select /Modify Item
Rewind
Play Recording
Fast Forward
●Record
Pause
■Stop Recording/Playback
Audio/Search Search Recorded files
Mute Turn on/off audio output

UserManual
5
Chapter 3: Installation
3.1 Install Hard Disk
NOTICE: Don’t take out HDD when DVR is running.
(1) Remove the screws around the top cover.
(2) Remove the top cover carefully.
(3) Connect the power cord and data cable to hard disk carefully.
(4) Use the provided screws to fix hard disk on the rack inside and then replace the
top cover of the case.
3.2 Connecting Camera and Monitor
There are 9 camera inputs and 1 Monitor output with BNC connectors (Refer to 2.2
Rear Panel).
3.3 VGA Output
There is 1 CRT or LCD monitor output with VGA port.
3.4 Connecting Power Supply
Please only use the power adapter supplied with the DVR.
Chapter 4: Starting the DVR
4.1 Firmware Version
After connecting the power adapter
and turning on the power button, the system
will boot-up and display the version and
released date of the DVR firmware.
2008.5.5
V 2.3
V-MLANG

UserManual
4.2 Detecting Installed Hard Drive
6
CHECKING HDD……
MASTER [WDC WD3200AAJB-00T]
SLAVE……
DVR will detect the installed hard drive and
display the hard drive information.
4.3 Format Hard Drive
Chapter 5: DVR Menu System
5.1 Navigating the Menus
(1) Press[MENU] to enter Main Menu
(2) Press[▲or ▼]to move the cursor
(3) Press [SEL] to select/modify
settings
(4)Press [MENU] again to exit or go
back to previous menu.
MAIN MENU
CAMERA SETUP
RECORD SETUP
RECORD FRAMERATE
VIDEOQUALITY NORMAL
RECORD SCHEDULE
SENSOR SETUP
HARD DRIVE SETUP
MISCELLANEOUS SETUP
NETWORK SETUP
LANGUAGE ENGLISH
RESET MENU
( )MOVE (SEL)SELECT (MENU)EXIT
CHECKING HDD……
MASTER [WDC WD3200AAJB-00T]-NEW-DVR
FORMAT HDD CONFIRM
(SELECT) FORMAT / (MENU) CANCEL?
When the DVR detects a new hard drive,
you will be prompted to format the hard drive
before using the DVR.
Press [SEL] to format or press [MENU]
to cancel.

UserManual
5.2 Menu Overview
MenuDirectory
Camera Setup
7
Record Setup
Record Frame rate
Video Quality
Record Schedule
Sensor Setup
Hard Drive Setup
Miscellaneous Setup
Network Setup
Language
Reset Menu
5.3 Camera Setup
Se
5.4 Record Setup
Camera Setup allows you to turn
cameras on or off.
Press [▲, ▼, ◄◄ and ►►]buttons
to select a channel and then press [SEL]
to modify the setting ON or OFF.
Note：If a camera channel is set to OFF ,it
will not be recorded(Refer to 6.4 Record
tup)
Main Menu
Change Password
Set Time
Hidden Channel
Audio Port Setup
PTZ Setup
Image Parameters
Password Enable
Keypad Tones
Seq.Dwell Time
VGA Setup
Record Setup allows you to set up
recording channels.
Press [▲, ▼, ◄◄ and ►►]buttons to
select a channel, and then press [SEL] to
modify the setting to ON or OFF.
If a channel is disabled in Camera Setup, it
will not record and the DVR will display
“NOCAM” on screen.
1 ON 2OFF 3ON
RECORD SETUP
4ON 5ON 6ON
7ON 8ON 9ON
( )MOVE （SEL）SELECT (MENU)EXIT
1 ON 2OFF 3ON
CAMERA SETUP
4ON 5ON 6ON
7ON 8ON 9ON
( )MOVE （SEL）SELECT (MENU) EXIT

UserManual
5.5 Record Frame Rate
8
6
f
I
a
(
t
The total frame rate is 50fps (PAL) or
0fps (NTSC). You can set the frame rate
or the channel which you selecte to record.
f the sum of the frame rate you select for
ll cameras is more than 50fps (PAL)/60fps
NTSC), the DVR will automatically adjust
he largest frame rate value to a smaller
value.
1 5 FPS 2 5 FPS 3 5 FPS
RECORD FRAMERATE
TOTAL 45FPS
4 5 FPS 5 5 FPS 6 5 FPS
7 5 FPS 8 5 FPSN 9 5 FPS
( )MOVE （SEL）+ ( □) - (MENU) EXIT
Press [▲, ▼, ◄◄ or ►►] button to select a channel, and then press [SEL] to
increase the value or press [■STOP] to reduce the value.
Note: Higher frame rate shows smooth images, but requires more hard drive
space.
5.6 Video Quality
Video Quality has 4 different settings:
Highest, High, Normal and Low.
The higher the video quality, the
better quality of Images, however higher
quality images require more hard drive
space.
MAIN MENU
CAMERA SETUP
RECORD SETUP
RECORD FRAMERATE
VIDEOQUALITY NORMAL
RECORD SCHEDULE
SENSOR SETUP
HARD DRIVE SETUP
MISCELLANEOUS SETUP
NETWORK SETUP
LANGUAGE ENGLISH
RESET MENU
( )MOVE (SEL)SELECT (MENU)EXIT
5.7 Record Schedule
Setting the Record Schedule allows you to customize the type of recording
depending on the time of day.
Press [SEL] to change the quality
setting.
The time line indicates 24 hours of a
day based on AM/PM (0 = 12).
Press [▲, ▼, ◄◄ or ►►] button
to select a time point, press [SEL] to
modify the recording mode.
RDCORD SCHEDULE
AM PM
0… 3… 6… 9… 0… 3…. 6… 9…
NO-RECORD
NORMAL-RECORD
SENSOR-RECORD
( )MOVE (SEL)SELECT (MENU)EXIT
S

UserManual
NO-RECORD [ white]: DVR will not record during the time.
NORMAL-RECORD [ red]: DVR will record continuously.
SENSOR-RECORD [S]: DVR will record when sensor or motion is triggered.
NOTE: In order to activate the record schedule, press the []record button when
viewing the cameras. After pressing the []record button, if schedule is set to
“NORMAL-RECORD” , the DVR will start to record immediately; if the schedule is
set to be “SENSOR-RECORD” , the DVR will not start recording until a motion is
detected by the DVR or an installed sensor is triggered.
5.8 Sensor Setup
9
CONT: Continuous alarm until any key is pressed
OFF: No alarm
Note: Sensored Record Time and Alarm On Time are measured in seconds
5.9 H/W Sensor Setup
Note: Sensors and extension alarm are not included with the DVR system and may
be purchased separately.
SENSOR SETUP
SENSORED RECORD TIME 30
ALARMONTIME OFF
H/W SENSOR SETUP
MOTION DETECTOR SETUP
( )MOVE (SEL)SELECT (MENU)EXIT
H/W SENSOR SETUP
CHANNEL-1 NOT INSTALLED
CHANNEL-2 TYPE:NORMAL-OPEN
CHANNEL-3 NOT INSTALLED
CHANNEL-4 NOT INSTALLED
CHANNEL-5 NOT INSTALLED
CHANNEL-6 NOT INSTALLED
CHANNEL-7 NOT INSTALLED
CHANNEL-8 NOT INSTALLED
CHANNEL-9 NOT INSTALLED
( )MOVE (SEL)SELECT (MENU)EXIT
Senso
r
e
d
Record Time indicates how
long the recording time is when the
motion or sensor is triggered.
Alarm On Time indicates whether the
buzzer will sound when motion is
detected.
HARDWARE SENSOR SETUP:
There are 3 different modes for sensor
setting: NOT INSTALLED,
NORMAL-CLOSE and NORMAL-OPEN.
Consult the alarm purchased for more details
on which setting is required.

UserManual
5.10 Motion Detector Setup
This section allows you to set up motion detection options for each camera.
MOTION DETECTOR SETUP:
ON/OFF: Enable or disable motion detection
recording.
10
Press “Stop” button to disable all areas, press “All” button to enable all areas
5.11 Hard Drive Setup
This section will display the current hard drive status and usage options
MOTION DETECTOR SETUP
CH1 ON LEVEL1 AREA
CH2 ON LEVEL2 AREA
CH3 ON LEVEL2 AREA
CH4 ON LEVEL2 AREA
CH5 ON LEVEL2 AREA
CH6 ON LEVEL2 AREA
CH7 ON LEVEL2 AREA
CH8 ON LEVEL2 AREA
CH9 ON LEVEL2 AREA
(
)
MOVE
(
SEL
)
SELECT
(
MENU
)
EXIT
HARD DRIVE SETUP
OVERWRITE ENABLED [ ON ]
ST3160215A
MASTER HDD SIZE 160133MB
MASTER HDD USED 124931MB 78%
MASTER HDD FORMAT
SLAVE HDD SIZE N/A
SLAVE HDD USED N/A
SLAVE HDD FORMAT
( )MOVE (SEL)SELECT (MENU)EXIT
LEVEL: Sensitivity for motion detection.
There are 3 levels sensitivity: Level 1-low,
level 3- highest
AREA: Select detectable area on the screen.
Area Selection:
Press [▲, ▼, ◄◄ or ►►]button to
select a block, and press [SEL] button to set
the block to detect motion. The area is
detectable when it is clear, the area is not
detectable when it is covert by shadow.
OVERWRITE ENABLED:
ON: Overwrite oldest video when hard drive
is full.
OFF: Stop recording when hard drive is full.
HDD SIZE: Indicates the total capacity of the hard drive installed in the DVR.
HDD USED: Indicates the space used in the hard disk drive for recording and the
percent used.

UserManual
HDD FORMAT: Will erase all video and data on the installed hard drive and make it
readable by the DVR
Note: You will be prompted for the password when formatting a hard drive. The
default password is “111111”
5.12 Miscellaneous Setup - Change Password
11
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
CURRENT PASSWORD
NEW PASSWORD
CONFIRM PASSWORD
[- - - - -]
[- - - - -]
[- - - - -]
[ 4 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ
This option allows you to change the
system password. The password must be
composed with six characters.
All keys can be used as password key
except the [MENU] key, which is used to
exit.
Enter the current password first, and
then enter six characters as your new
password, repeat the new password to
confirm.
If you forget your password, please
contact technical support for assistance.
5.13 Miscellaneous Setup - Set Time
SET TIME
2008/11/11 17:50:01
( )MOVE (SEL)SELECT (MENU)EXIT
The system date and time format is
YYYY/MM/DD and HH:MM: SS.
Press [◄◄] or [►►] button to select the
data to modify, press [SEL] to modify. Press
[MENU] to save and return to previous
menu.

UserManual
5.14 Miscellaneous Setup - Hidden Channel
12
The system provides a function to hide a
channel in monitoring mode. The selected
channel can still be recorded while it’s hidden;
the hidden picture is viewable during playing
back.
Press [SEL] to select a channel to hide.
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
[ 4 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 60HZ
5.15 Miscellaneous Setup - Audio Port Setup
5.16 Miscellaneous Setup - PTZ Setup
Press [SEL] to select the camera, press[◄◄] and [►►] buttons to assign the ID.
Note: the ID must be unique．
You can select the audio recording
function to ON or OFF, and select the
video channel that you like to record the
audio on.
SPEED: Set the baud rate (2400，4800，
9600，19200，38400) to match your speed
dome.
PROTOCOL: Supports “PELCO-D” and
“PELCO-P”. Select the protocol according to
your speed dome’s protocol.
CAMERA: select the camera channel which
is connected with the speed dome.
ID: Assign an ID to your speed dome.
PTZ SETUP
SPEED [4800]
PROTOCOL [PELCO-D]
CAMERA- [ 1 ] ID [ 1 ]
( )MOVE ( )CAMID
(SEL)SELECT (MENU)EXIT
AUDIO PORT SETUP
AUDIO PORT1-VIDEIO CHANNEL
AUDIO PORT1-RECORD
( )MOVE (SEL)SELECT (MENU)EXIT
[ 1 ]
[ OFF ]

UserManual
5.17 Miscellaneous Setup - Image Parameters
13
5.18 Miscellaneous Setup - Password Enable
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
[ 1 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ
[ 1 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ
You can adjust the image parameters
according to your needs.
Move the cursor to this selection and
press[◄◄] or [►►] button to select a
channel you want to adjust, then press
[SEL] button to edit parameters.
CON: Contrast
BRI: Brightness
HUE: Hue
SAT: Saturation
Press [▲] or [▼] to select the item，
and then press [◄◄] or [►►] buttons
to adjust the value.
The password will be required to
control the DVR when this option is set to
“ON”, and the password is not required
when this option is set to “OFF”.

UserManual
5.19 Miscellaneous Setup - Keypad Tones
14
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
5.20 Miscellaneous Setup – SEQ.Dwell Time
auto-sequence display function and press[◄◄] again to turn off this function in
preview mode
5.21 Miscellaneous Setup - VGA Setup
This function allows you to enable
/disable buzzer sound when pressing a
button. Press [SEL] to select ON or
OFF.
Select a VGA resolution to match your
CRT or LCD monitor.
5.22 Network Setup
Network Setup allows you to prepare the DVR for viewing over the internet or
local network.
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
[ 4 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ
[ 4 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ
MISCELLANEOUS SETUP
CHANGE PASSWORD
SET TIME
This function allows you to set the
dwell time for each camera when you
enabe the auto sequence display function.
Press [◄◄] and [►►] buttons to
adjust the value.
After setting, press [◄◄] to turn on
HIDDEN CHANNEL
AUDIO PORT SETUP
PTZ SETUP
IMAGE PARAMETERS
PASSWORD ENABLE
KEYPAD TONES
SEQ.DWELL TIME
VGASETUP
( )MOVE (SEL)SELECT (MENU)EXIT
[ 4 ]
[ CH4 ]
[ OFF ]
[ ON ]
[OFF ]
1024*768 75HZ

UserManual
15
IMPORTANT: This setting should only be changed if multiple DVRs are being setup on the same
network and the first code “00” must not to be changed.
NETWORK SETUP
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
[ 80]
MACADDRESS: In a local area network(LAN)，
the MAC (Media Access Control) address is
your computer’s unique hardware identity code
(On an Ethernet LAN，it is the same as your
Ethernet address).When you are connected to
the Internet from your computer (or host as the
Internet protocol thinks of it )，a corresponding
table relates your IP address to your computer’s
physical (MAC) address on the LAN.
IP ALLOCATION: DVR supports DHCP and
Static IP modes. If your modem/router supports
DHCP function, you can use DHCP mode. When
using STATIC mode, you will be required to setup
your IP settings manually.
Note: After setting the DVR to DHCP mode restart
the unit.
IP Address: In a local network, the IP address is
a unique designated address for your DVR
recognized by your router. Ensure this number is
within the range usable by your modem/router.
Use the UP “▲” and DOWN “▼” buttons to
move the cursor and use the “SEL” button to
change the numbers. Once you have finished the
changes restart your DVR.
SUBNET MASK: Subnet Mask is used to
determine what subnet an IP address belongs to.
A number that is used to identify a sub network
so that IP addresses can be recognized on a local
area network. Consult your modem/router for
your LAN’s subnet mask.
NETWORK SETUP
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
NETWORK SETUP
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
[ 80]
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
NETWORK SETUP
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
[ 80]
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
[ 80]

UserManual
16
NOTE: To adjust the IP ADDRESS，SUBNET MASK and GATEWAY value, only when the
[STATIC] mode is being selected.
GATEWAY: Set this number to the gateway
set by your modem/router.
DNS ADDRESS: This code should be provided
by your local ISP.
HTTP PORT: This port number is used to
communicate with PC Client. The default value is
80(Can be changed from 1024 to 49151)
USER SETUP: When accessing the DVR
from a remote location you will be prompted
for a login and password. The default is
“admin” for full administrator rights. Set “User
ID” and password to setup a user with limited
rights to prevent tampering.
NETWORK SETUP
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
[ 80]
NETWORK SETUP
MAC ADDRESS <00:11:22:33:44:55>
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
DDNS SETUP
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
NETWORK SETUP
MAC ADDRESS
IPALLOCATION
IPADDRESS
SUBNET MASK
GATEWAY
DNS1 ADDRESS
DNS2 ADDRESS
HTTP PORT
USER SETUP
DDNS SETUP
[0.0.0.0]
[0.0.0.0]
[ 80]
<00:11:22:33:44:55>
[STATIC]
[192.168.1.100]
[255.255.255.0]
[192.168.1.1]
[0.0.0.0]
[0.0.0.0]
(HTTP PORT) 80, 1024-49151
( )MOVE (SEL)SELECT (MENU)EXIT
[ 80]
USER SETUP
ADMIN ID …… [admin]
ADMIN PASSWORD [admin]
[ ]
USERID
USER PASSWORD [ ]
( )MOVE (SEL)SELECT (MENU)EXIT

UserManual
17
DDNS SETUP：If you require an external
service to maintain a dynamic IP address enter
the user information here.
DDNS SETUP
DDNS PROVIDER [WWW.DynDNS.com ]
DDNS USER NAME [ ]
[ ]
DDNS PASSWORD
DOMAINNAME
[
]
( )MOVE (SEL)SELECT (MENU)EXIT
LAN-DVR Connection
See the diagram below for steps to connect your DVR to a local area network or the internet.
For remote monitoring from your computer，you must have a LAN connection available or
broadband Internet access.
You need to register a www.dyndns.com to get a free account .After registration，you will have
a username and password. You can also register your domain name on the website. Please refer to
Chapter 5 “Network Setup” for more details. There you will learn how to input the Dyndns
username，password，and domain name. You can log in from anywhere by using Internet Explorer
and entering your DVR’s domain name.

UserManual
5.23 Language
You can change the OSD language
from the default English to other langu-
ages.
18
5.24 Reset Menu
If you select this item, the system will restore all your settings to factory default
values. You need to enter your password to reset the menu.
5.25 NTSC/PAL Output select
Change the jumper JS1 to select NTSC
or PAL video output format according to the
silkscreen on the PCB.
MAIN MENU
CAMERA SETUP
RECORD SETUP
RECORD FRAMERATE
VIDEOQUALITY NORMAL
RECORD SCHEDULE
SENSOR SETUP
HARD DRIVE SETUP
MISCELLANEOUS SETUP
NETWORK SETUP
LANGUAGE ENGLISH
RESET MENU
( )MOVE (SEL)SELECT (MENU)EXIT

UserManual
Chapter 6: Record
6.1 Start Recording
Press [●] record button to start recording according to the record schedule you
have set. System will display some information on screen.
[●]: the red pot next to the channel name indicates that the channel is being
recorded.
[A-REC]: indicates the current record schedule is set to NORMAL-RECORD mode.
[S-REC]: indicates the current record schedule is set to SENSOR-RECORD mode.
[N-REC]: indicates the current record schedule is set to NO-RECORD mode.
[39%]: indicates the percentage of hard disk space used.
[M]: HDD info ([M] Master Hard Disk)
6.2 Audio Recording
[ ]: indicates this video channel is bundled with an audio port, and the audio
output is on.
[]: indicates the audio output is off.
[]: indicates the audio is being recorded and the audio output is on.
You could press [MUTE] button on front panel to be mute mode for audio output.
The audio input can be still recorded while the output is mute.
19