LUCCI Air Tempair 200290 User manual

TEMPAIR 3 IN 1 EXHAUST FAN
SKU# 200290 & 200291
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Tempair 3 in 1 Exhaust Fan Installation Instructions
1 | P a g e V e r 1 . 3
WARRANTY
- This product is covered by a 3 year warranty. The warranty is from date of purchase, not the date of
installation.
- If the fitting is not installed by a licensed electrician the warranty will be void.
- All wiring and installation of the fitting must adhere to local and national wiring rules.
eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
- Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty
enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the fitting.
- Failure to comply with the instructions in this manual may cause damage or injury and will void warranty.
GENERAL SAFETY WARNING
1. Use this heater in accordance to instructions outlined in this manual.
2. Ensure power is turned off before installation.
3. The heater must be properly grounded.
4. Do not touch heat lamps or glass fascia when in use.
5. To not look directly at the heat lamps during use.
6. Wait for the heater to cool down before cleaning or replacing lamps.
7. Never use the heater without the glass panel or fascia.
8. This appliance is not to be used by persons, including children, with reduced physical, mental or sensory
capabilities, or lack of knowledge and understanding, unless they are supervised and or given instruction
concerning the use of the appliance by someone responsible for their safety
9. This appliance is not a toy. Children should be supervised to ensure that they do not play with the
appliance.
INSTALLATION WARNINGS
1. This heater must not be located / installed immediately below a socket outlet.
2. When used in a bathroom this heater is to be installed so that switches and other controls cannot be touched
by a person in the bath or shower.
3. This heater shall, under no circumstances, be covered with insulating material or similar material.
4. Regulations concerning the discharge of air have to be fulfilled.
5. Joists, beams and rafters shall not be cut or notched to install this heater.
6. Installation is to be no less than 2.1 metres from the floor.
7. The product must be installed in a flat ceiling. Do not install on a sloped ceiling, or vertically.
8. Take care not to pull any electrical wires during unpacking as this may damage the connection.
9. Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.

Tempair 3 in 1 Exhaust Fan Installation Instructions
2 | P a g e V e r 1 . 3
10. Check whether the fitting has been damaged during transport. Do not operate/install any product which
appears damaged in any way. Return the complete product to the place of purchase for inspection, repair
or replacement.
PERFORMANCE NOTES
1. For exhaust fan optimum performance, volume of air being extracted should be equal to the amount of
air entering the room. Air is drawn mostly from under a door, or an open window. If the bathroom or room
is air tight (door and windows shut), the exhaust will not perform well.
2. The heat lamps will work most effectively if you are standing directly under the appliance.
3. LED lighting of the appliance is designed to provide directional lighting only. While it may be sufficient for
most common tasks, others such as shaving or applying make-up may require additional lighting.
PARTS
Halogen heat lamp (500W per lamp)
A
Air outlet
B
Air inlet
C
LED lamp
D
Ducted Fan (100mm)
E
Duct (4 metres)
F
Wall switch
Not shown
Grille
Not shown
Fig. 1.1 HEATER UNIT
Fig. 1.2 HEATER UNIT

Tempair 3 in 1 Exhaust Fan Installation Instructions
3 | P a g e V e r 1 . 3
E
F
INSTALLATION INSTRUCTIONS
1. Locate a suitable location in which you wish to install the heater. Note it should not be in an area where
the product may come in contact with water such as above a shower or bath. The centre of a room is
ideal. (Fig. 3)
Fig. 1.3
Fig. 1.4
Fig. 2

Tempair 3 in 1 Exhaust Fan Installation Instructions
4 | P a g e V e r 1 . 3
2. Ensure the appliance is installed, recessed into a ceiling at least 2.1 metres from the floor.
3. Cut a hole in the ceiling of 326mm x 462mm.
4. Locate a suitable position on the ceiling space for the Ducted Fan unit, preferably near the heater unit as
shown in the diagram above (Fig. 2 & 3), and the direction of airflow is correct before securing into
position.
5. Determine the length of ducting required between heater unit outlet and ducted fan inlet. 4 meters of
ducting are provided. Cut ducting to appropriate length and connect the heater unit and ducted fan. Use
tape to secure this duct connection if required.
6. Using the remaining ducting, fit this to the outlet of the ducted fan (note the direction of the air flow) and
feed to outlet of the wall grille. We recommend the location of the grille (Fig.6) on the exterior
wall/surface of the building in such that the ducting is routed as straight and linear as possible between
the ducted fan and the grille outlet. This will ensure best air extraction.
7. Locate the terminal block on the back of the heater unit (under the cover). Connect the supply wires from
the Ducted Fan to the terminal block via the hole on the side. Complete in accordance with the wiring
diagram shown in Fig. 5
8. Make the wiring connection of the wall switch supplied to the terminal block on the heater unit, using
wiring diagram shown in Fig. 5, and secure the terminal box cover.
Fig. 3