lumen8 Kudos 108 User manual

Kudos 108
Order code: ELUM030
UserGuide
Professional Entertainment Technology

1
A
TABLE OF CONTENTS
1. Safety Instruction
2. Features and Technical Specifications
3. How To Set Up The Unit
4. How To Control The Unit
5. Troubleshooting
6. Fixture Cleaning

2
A
1. Safety Instruction
WARNING
yPlease keep this User Guide for future consultation. If you sell the unit to
another user, be sure that they also receive this instruction booklet.
yUnpack and check carefully there is no transportation damage before using
the unit.
yBefore operating, ensure that the voltage and frequency of power supply
match the power requirements of the unit.
yIt’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
yThe unit is for indoor use only. Use only in a dry location.
yThe unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
yDisconnect main power before replacement or servicing.
yMake sure there is no flammable materials close to the unit while operating
as it is fire hazard.
yUse safety cable when fixes this unit. Don’t handle the unit by taking its
head only, but always by taking its base.
yMaximum ambient temperature is ta: 40℃. Don’t operate it where the
temperature is higher than this.
yUnit surface temperature may reach up to 85℃. Don’t touch the housing
bare-hand during its operation. Turn off the power and allow about 15
Please read carefully the instruction, which includes
important information about the installation, usage and
maintenance.

3
A
minutes for the unit to cool down before replacing or serving.
yIn the event of serious operating problem, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare
parts.
yDo not touch any wire during operation as high voltage might be causing
electric shock.
Warning
yTo prevent or reduce the risk of electrical shock or fire, do not expose the
unit to rain or moisture.
yDo not open the unit within five minutes after switching off.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are
visibly damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs yourself. In the unlikely event your unit may
require service, please contact your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. And make sure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit’s weight.
Also always use a safety cable that can hold 12 times of the weight of the

4
A
unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a
place where is out of the touch of people and has no one pass by or under
it.
2. Features and Technical Specification
• DMX Channels: 1/9/12/16
• Pan/Tilt: 630°/240°, speed adjustable
• Smooth electronic dimming: 0-100%
• Electronic strobe with pulse and random effects
• Optional easy controller CA-8 or CA-9 RTX
• High efficiency, low power consumption
•Super compact, low weight
•Voltage: 100V~240V, 50/60Hz
• Fuse: T 6.3A
• Power consumption: 110W
•Light source: 36 x 3W LEDs (R8, G10, B10,W8)
•Dimension: 304 x 267 x 167 mm
• Weight: 5.7kgs

5
A
Photometric diagram:
3. How To Set The Unit
3.1 Control panel
Display
To show the various menus and the selected functions
LED
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions

6
A
Only for remote control
Connecting with CA-8/CA-9/CA-9RTX to control the unit for Stand by,
Function and Mode function.
Mains input
Connect to power supply.
Mains output
Connect to supply power to the next unit.
DMX input/output
For DMX512 link, use 3/5-pin XLR cable to link the unit together.
3.2 Main Function
To select any of the given functions, press the MENU button up to when the
required one is showing on the display. Select the function by ENTER button
and the display will blink. Use DOWN and UP button to change the mode.
Once the required mode has been selected, press the ENTER button to
setup, to go back to the functions without any change press the MENU
button again. Hold and press the MENU button about one second or wait for
one minute to exit the menu mode.
The main functions are showing below:

7
A

8
A
DMX Address
Select DMX Address, press the ENTER button to confirm, the present
address will blink on the display. Use the UP and DOWN button to adjust the
address from 1to 512. Once the address has been selected, press the
ENTER button to setup, to go back to the functions without any change
press the MENU button again. Hold and press the MENU button about one
second or wait for one minute to exit the menu mode.
Channel Mode
Select Channel mode, press the ENTER button to confirm, the present
address will blink on the display. Use the UP and DOWN button to select
9channels (mode1), 12channels (mode2), 16channels (mode3). Once the
channel mode has been selected, press the ENTER button to setup, to go
back to the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Show Mode
Select Show Mode, press the ENTER button to confirm, present mode will
blink on the display. Use the DOWN and UP button to select the Show 1 or
Show 2 or Show 3 or Show 4 mode. Once the mode has been selected,
press the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Hold and press the MENU button

9
A
about one second or wait for one minute to exit the menu mode.
Dimmer Curve
Select Dimmer Curve, press the ENTER button to confirm, present mode
will blink on the display. Use the DOWN and UP button to select the mode 1
or mode 2 or mode 3 or mode 4 mode. Once the mode has been selected,
press the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Hold and press the MENU button
about one second or wait for one minute to exit the menu mode.
Mode 1(Optically Linear): The increase in light intensity appears to be
linear as DMX value is increased.
Mode 2(Square Law): Light intensity control is finer at low levels and
coarser at high levels.
Mode 3(Inverse Square Law): Light intensity control is coarser at low levels
and finer at high levels.
Mode 4(S-cure): Light intensity control is finer at low levels and high levels
and coarser at medium levels.