lumen8 Liberty 7HEX12 User manual

Order codes:
ELUM118 - Black housing
ELUM118A - White housing
Liberty 7HEX12 Battery Uplighter
7 x 12W 6-in-1 colour LED (RGBAWUV)
User Manual
Optional
IR remote
Order ref:
LEDJ90F
Convection
cooled,
no fan!

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Twoyearsfromdateofpurchase.
• NOTE:Batteriesareclassedasconsumableitemswhich
arecoveredfor90daysfromdateofpurchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
3
Product overview & technical specications
Housing7x12W6-in-1colourLEDs,theLiberty7HEX12
batteryuplightergivessmoothcolourmixingfromrich
saturatedhuestosubtlepastelshades.Theseunitshave
ruggedhousingandfeaturesa25°beamangle.The4push
buttonLCDmenuallowsforeasyaccesstothefunctions
includingDMX,master/slave,soundactiveandstandalone.
•2yearwarranty
•7x12W6-in-1colourLED(RGBAWUV)
•Beamangle:25°(eldangle:35°)
•DMXchannels:2,3,3,6or9selectable
•WirelessDMXcontrolfrom“WirelessSolutions”Sweden
•Staticcolour,colourchange,colourfade,auto,
soundactiveandmaster/slavemodes
•0-100%dimmingandvariablestrobe
•4pushbuttonmenuwithLCDdisplay
•Rechargeablebatteryforwirelessapplications
•3-pinXLRin/outsockets
•IECin/outsockets
•Convectioncooled
•OptionalIRremote(LEDJ90F)
Liberty 7HEX12 battery uplighter
25° - Lux
0m 1m 2m 3m 4m 5m
5690 1945 887
25°
468 337
220mm 190mm
265mm
Specications Liberty 7HEX12 battery uplighter
Powerconsumption 155W(whencharging)
Batterylife 5-7hours*(fullon)
18-20hours*(colourfade)
Batteryrechargetime 5hours
Powersupply 100~240V,50/60Hz
Dimensions 265x220x190mm
Weight 6.1kg
Ordercode ELUM118-Blackhousing
Ordercode ELUM118A-Whitehousing
*battery life subject to usage and the environment
where the xture is situated.

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
4
Angle adjustment:
Usethetighteningknobsoneithersideofthexture
toadjusttheanglefrom0-90°.
Technical specications
Operating instructions
DMX IN
MIC
ON
OFF
DMX OUT
MODE ENTER UP DOWN
FUSE:F2A~250V
POWER IN
AC 100~240V, 50/60Hz POWER OUT
AC 100~240V, 50/60Hz
www.elumen8.co.uk
LIBERTY 7HEX12
UPLIGHTER
Charge
Indicator
Wireless
DMX Signal
Indicator
Battery Indicator
01-Microphone
02-Earthpoint
03-IECpowerinsocket
04-FuseF2A250V
05-DMXinsocket
06-DMXoutsocket
07-IECpoweroutsocket
08-Functionbuttons
09-On/offbuttons
10-LCDdisplay
11-WirelessDMX
antenna
12-Tighteningknobsforangle
adjustment
13-Batteryindicator
14-ChargeIndicator
15-WirelessDMXsignalindicator
Inthebox:1 x xture,
1 x IEC mains cable &
1 x user manual
01
08
09
14
15
1212
10
11
02
03 04 05 06 07 13

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
5
DMX channel mode:
OperatinginDMXcontrolmodegivestheuserthegreatestexibilitywhenitcomestocustomisingor
creatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthextureandeach
xtureindependently.
ToaccesstheDMXchannelmode,pressthe“MENU”buttonontherearoftheunittoshow“CHANNEL”
ontheLCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochoose
oneofthe2,3,3,6or9DMXchannelmodes.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Channel Value Function
1000-255 Masterdimmer(0-100%)
2
000-255colourmacro
000-016 Red
017-033 Green
034-050 Blue
051-067 White
068-084 Amber
085-101 UV
102-118 Yellow(R-225,G-200,A-255)
119-135 Cyan(G-255,B-255)
136-152 Lavender(R-170,B-210)
153-169 Brightgreen(G-255,A-180)
170-186 Magenta(R-255,B-90,UV-255)
187-203 Turquoise(G-255,B-180,UV-255)
204-220 Orange(R-200,A-200)
221-237 Coolwhite(R-70,G-190,B-255,A-200)
238-255 Warmwhite(R-230,G-255,B-255,A-255,W-255)
2 channel mode:

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
6
Channel Value Function
1000-255 Masterdimmer(0-100%)
2000-255 Flash(speed0-100%,1Hz-20Hz)
3000-004 Blackout
005-010 Red
011-015 Green
016-020 Blue
021-025 White
026-030 Amber
031-035 UV
036-040 Yellow(R-255,G-200,A-255)
041-045 Cyan(G-255,B-255)
046-050 Lavender(R-170,B-210)
051-055 Brightgreen(G-255,A-180)
056-060 Magenta(R-255,B-90,UV-255)
061-065 Turquoise(G-255,B-180,UV-255)
066-070 Orange(R-200,A-200)
071-075 Coolwhite(R-70,G-190,B-255,A-200)
076-080 Warmwhite(R-230,G-255,B-255,A-255,W-255)
081-150 Colourjumpingspeed
Slowest(081)changesevery8secs
Fastest(150)changesevery0.3secs
151-220 Colourfadingspeed
Slowest(151)changesevery8secs
Fastest(220)changesevery0.3secs
221-255 Soundcontrol(micsensitivity)
3 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
3 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
5 000-255 Amber(0-100%)
6 000-255 UV(0-100%)
6 channel mode:

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
7
DMX address examples:
TosettheDMXaddress,pressthe“MENU”buttonontherearoftheunittoshow“DMXMODE”
ontheLCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochoose
betweentheadresses000-512.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Colour mode:
Toaccessthestaticcolourmode,pressthe“MODE”buttonontherearoftheunittoshow“1.STATIC”
ontheLCDdisplay.Thenpressthe“ENTER” buttonandusethe“UP”and“DOWN”buttonstochange
betweenstaticcolour,colourchange(7colour),colourchange(3colour)andcolourfademodes.Press
the“ENTER”buttontoconrmthesetting.Nowusethe“UP”and“DOWN”buttonstoselecttheRGB
brightnessandF(ash)speed.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Channel Value Function
1000-255 Masterdimmer(0-100%)
2000-255 Flash(speed0-100%,1Hz-20Hz)
3000-255 Red(0-100%)
4000-255 Green(0-100%)
5 000-255 Blue(0-100%)
6 000-255 White(0-100%)
7 000-255 Amber(0-100%)
8000-255 UV(0-100%)
9 000-004 Blackout
005-010 Red
011-015 Green
016-020 Blue
021-025 White
026-030 Amber
031-035 UV
036-040 Yellow(R-255,G-200,A-255)
041-045 Cyan(G-255,B-255)
046-050 Lavender(R-170,B-210)
051-055 Brightgreen(G-255,A-180)
056-060 Magenta(R-255,B-90,UV-255)
061-065 Turquoise(G-255,B-180,UV-255)
066-070 Orange(R-200,A-200)
071-075 Coolwhite(R-70,G-190,B-255,A-200)
076-080 Warmwhite(R-230,G-255,B-255,A-255,W-255)
081-150 Colourjumpingspeed:slowest(081)changesevery8secs,fastest(150)changesevery0.3secs
151-220 Colourfadingspeed:slowest(151)changesevery8secs,fastest(220)changesevery0.3secs
221-255 Soundcontrol(micsensitivity)
9 channel mode:

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
8
Master/slave mode:
Tosetthemasterunit,pressthe“MODE”buttonontherearofthemasterunitthenselectyour
desiredprogram(soundactive,auto,staticcolour,colourfadeoroneofthebuilt-inprograms).
Tosettheotherunitsinslavemode,pressthe“MODE”buttonontherearoftheunittoshow“SLAVE
MODE”ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitwillnowrunin
sequencewiththemasterunit.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Sound active mode:
Toaccessthesoundactivemode,pressthe“MODE”buttonontherearoftheunittoshow“SOUND
SENS”ontheLCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoset
thesoundsensitivitylevelfrom00-31.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Battery reference information:
WhenthebatterychargeindicatorLEDisilluminatedred,thextureisrecharging.Whenthebattery
chargeindicatorLEDisilluminatedgreen,thextureischarged.WhenthebatterylifeindicatorLED(s)
areilluminatedgreen,thefollowingrulesapply:
4 indicators-100%charged,3 indicators-75%charged,
2 indicators-50%charged,1 indicator -25%charged
Therechargingtimeforthebatteryis5hours.
Thebatteryusagetimefromfullychargedisdependantonthemodeandbrightnessofthexture.
Formoreinformationpleaseseethespecicationstableonpage3.
Wireless DMX:
ToactivatethewirelessDMXreceiverpressthemodebuttonuntilthedisplayshows“WirelessOff”,
press“ENTER” toaccessthemenuandthen“UP/DOWN”toselect“WirelessOn”.
WhenthewirelessDMXsignalindicatorLEDisilluminatedred,thewirelessreceiverisnotactive.
WhenthewirelessDMXsignalindicatorLEDisashingredandgreen,thewirelessDMXreceiverison
andistryingtoconnecttothewirelessDMXtransmitter.
WhenthewirelessDMXsignalindicatorLEDisgreen,theconnectiontothewirelessDMXtransmitter
isgood.
WhenthewirelessDMXsignalindicatorLEDisgreen(on)andred(ashing)itmeanstheconnectionis
good,butthextureisnotreceivingtheDMXsignalfromthetransmitter.

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
9
Optional IR remote functions:
Button functions:
DMX address examples:
Important notes:
• SettheDMXaddressoneachxturebeforepluggingintotheDMXcontroller
• TheIRremoteiscannotbeusedwhenthexture(s)arebeingcontrolledbyaDMXcontroller
• Themaximumtransmitterdistanceis10m-PleasemakesurethatyouhavetheIRremoteaimed
directlyatthefrontpanelofeachxturetobeprogrammed
• Ifyoudonotpressthe“DMXMODE”buttonafteryouhavechangedtheDMXaddress,
whenyoupowerdownthextureitwilllosetheaddressyouhaveset
01-Blackout
02-SettheLEDscolour,thenusethe‘+’and‘-’
buttonstochangethebrightness
03-Setinautorun
04-Runthebuilt-inprograms,thenusethe‘+’and‘-’
buttonstogothroughtheprograms
05-SettheLEDstoashonandoff,thenusethe‘+’
and‘-’buttonstochangetheashfrequency
06-Settherunspeed,thenusethe‘+’and‘-’buttons
tochangethedesiredspeed
(note:onlyavailableinthecolourchangeor
colourfademodes)
07-SettheLEDsintoDMXmode
08-SettheLEDintosoundactivemode
09-SettheLEDsintoslavemode
10-SettheDMXaddressfortheLEDs
1 2 3
4 5 6 0
+
_
7 8 9
AR
D
FL
SL
SP
S
S PR
SA
RG B
WAUV
BLACKOUT DIMMING
FLASH
SLAVE
SPEED
SET ADDR
SELECT PROG
SOUND ACTIVE
AUTO RUN
DMX MODE
01
02
04 05
09
03
07
08
06
10
10
Optional
IR remote
Order code:
LEDJ90F
TosettheDMXaddress“245”;
• Pressthe“S”button,theredLEDswillcomeon,
youcannowstarttosettheDMXaddress
• Nowpressthe“2”button,thegreenLEDswill
comeon,thismeanstherstdigithasbeen
setat2
• Nowpressthe“4”button,theblueLEDswill
comeon,thismeanstheseconddigithasbeen
setat4
• Nowpressthe“5”button,andallofthe
R,G,BLEDswillcomeon,thethirddigit5
hasbeenset.ThefullDMXaddresssetting
hasbeenchanged
• Nowpressthe“DMXMODE”buttontosave
thenewaddressintothememory

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
10
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
11
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order code: CABL90, 5-pin - Order code: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.elumen8.co.uk Liberty 7HEX12 Battery Uplighter User Manual
12
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.
Optional accessories & WEEE notice
Pleasecontactyourlocalretailertopurchase
theseaccessories.
Optional IR remote
Order code: LEDJ90F
1 2 3
4 5 6 0
+
_
7 8 9
AR
D
FL
SL
SP
S
S PR
SA
RG B
WAUV
BLACKOUT DIMMING
FLASH
SLAVE
SPEED
SET ADDR
SELECT PROG
SOUND ACTIVE
AUTO RUN
DMX MODE
Tokeepup-to-dateonthelatestaccessories
andproductrangeadditionsplease
visitwww.prolight.co.uk