Lumio InnovaPlas 71550 User manual

Owner’s Manual
#71550
Read the instruction manual carefully before assembly and use.
Please also save it for future reference.
A-Frame Ladder

1
Table of Content
1. Product Introduction................................................................................................................................ 2
2. Warning and Caution ............................................................................................................................... 2
3. Assembly and Use Instructions .............................................................................................................. 3
4. Routine Maintenance ............................................................................................................................. 9
5. Parameter List ........................................................................................................................................ 9
6. Explosion Diagram and List of Accessories ............................................................................................. 10

2
1. Product Introduction
The A-Frame ladder adopts blow molding process and polyethylene material, which has strong corrosion-resistance
feature. The whole ladder has been polished to ensure a nice foot touch. The treads have round embossments
which effectively prevents slipping. Enforced thick material guarantees the safety, stability and durability.
The ladder is suitable for 48 -54″ aboveground swimming pools. The external ladder is designed to be swung up.
When the swimming pool is not in use, the external ladder can be swung up and fixed to prevent children from
accidentally entering.

3

4
3. Assembly and Use Instruction
a) Remove the A-Frame ladder and its accessories from the box and check that all the accessories are complete.
b) Place one of the bottom tread on a flat surface with the grooved side facing up; then snap the two holders
into the grooves.
Note: The two holders need to be snapped into the groove in the same direction.
c) Install four treads to the holders, as illustrated below. Fix the top tread to the holders with #10x1-1/4″screws.
d) Fix the left and right fixing strips with bolts, washers (M6), and nuts (M6*85). Do not overtighten (the
accessories are in screw kit #5862050002)
e) Use #10x1-1/4″ screws to fix the other three treads, then put aside for further processes.
Tighten with screws for both
right and left sides
Bolt
Washer
Nut
Holder
Left fixing strip
Needs to be fixed with screws
Right fixing strip

5
f) Place the second bottom tread on a flat surface with the grooved side facing up; then snap the two holders
into the groove.
Note: The two holders need to be snapped into the groove in the same direction.
g) Fix the treads to the holders with #10x1-1/4″screws.
h) Place the lower base of the entrapment barrier on a level surface. Snap the front barrier into the groove on
the lower base facing the round edge. Snap the rear barrier into the groove on the lower base facing the
straight side.
i)
Lower base
Fix the treads to the left and
right fixing strips with screws.
Fix the treads to holders with screws
Front barrier
Rear barrier
Tighten with two screws
on each side
Holder

6
j) Slide the upper brace over the front barrier as shown. Slide the upper brace through the groove in the rear
barrier and push down lightly to secure.
k) Fix the lower base of the entrapment barrier into the bottom step of the inside portion of the A-Frame
ladder with 2 #10x1-1/4” screws.
l) Fix the remaining two treads with #10x1-1/4″screws
into the grooves of the holders.
Upper brace
Install the treads
with screws
Slide the upper brace through
the groove
Fix the barrier onto
these two positions

7
m) This ladder is designed to fit multiple pool heights.
If you pool height is 52″, locate the first line on the handrail of the ladder. Using a hacksaw, cut the handrail
evenly through both sides
If your pool height is 48″, locate the second line on the handrail and, using a hacksaw, cut the handrail
evenly through both sides. Locate the line on the holder and cut the redundancies evenly through both
sides.
No cut needed if your pool height is 54″.
n) Using a funnel, fill both holders with sand. Use approximately 20 Lbs. of sand in each holder. The entrapment
barrier in step K has a front and rear barrier.
52″ cut line
48″cut line
48” cut line for holder
Fill holder with sand using a funnel

8
o) Assemble the handrails to the platform, center the cover cap opening on the side of the handrail where the
platform was just attached. Using a rubber mallet/hammer, tap on the cap until it is flush with the handrail.
p) Attach the handrails by pushing them down over the holders.
q) Secure all handrails to the legs with #10x1-1/4” screws.
r) Place the assembled ladder inside the pool where you would like to enter and exit. The entrapment barrier
should be inside of the pool. Once the ladder is placed in the pool, tip the ladder forward and backward and
side to side to release any air that may be trapped inside. Be careful, the corners of the ladder can be sharp,
special attention is required to protect the liner when putting the ladder in water.
It is strongly recommended to sand the sharp corners.
When a ladder is installed, it is recommended that a step mat should be installed underneath.
THIS ITEM IS SOLD SEPARATELY.
Cover cap
Deck platform
Handrail
Push handrails down
over the holders
Step O
Step P
Screw
Warning!!
The swing up tread
must be installed
on the outside of
the pool. Risk of
drowning!

9
s) The A-Frame ladder must be fixed on the edge of the pool. First, align the two holes on the surface of the
deck platform with the edge of the pool, mark the hole positions at the edge of the pool with a fine marker
pen, then drill through the edge of the swimming pool with a 5/16” drill bit. Finally, use bolts, nuts and
washers to fix the ladder on the edge of the swimming pool.
(1) Use 5862050000 screw kit (2.5” bolt) if your pool height is 48″
(2) Use 5862050001 screw kit (5” bolt) if your pool height is 52″
(3) Use 5862050001 screw kit (5” bolt) if your pool height is 54″
Deck platform
Pool edge
Bolt

10
4. Routine Maintenance
When the swimming pool is not in use, it is recommended to flip the outer ladder upwards, then push it down and fix
it.
Winterize
a) In winter, the ladder must be removed.
b) When removing the ladder, it is recommended to wash it with fresh water to remove the chemicals on the
surface.
c) Store the ladder in a warm and dry place for reuse in the next year.
5. Parameter List
No.
Description
Specification
1
Application
48”-54” height aboveground pool
2
Weight limit
250 lbs
3
Material
Polyethylene
4
Product Size
1070*646*1966 MM
5
Gross Weight
6
Package Size
600*200*1510 MM

11
6. Product Explosion Diagram and Accessories (parts number page 12)

12
No.
Part Number
Description
Qty
1
47155001
Handrail
2
2
48850112
Cover Cap
4
3
47155011
Deck Platform
1
4
47155005
Holder
4
5
47155002
Tread
8
6
47155008
Bottom Tread
2
7
47155003
Upper Brace
1
8
47155009
Front Barrier
1
9
47155010
Back Barrier
1
No.
Part Number
Description
Qty
10
47155004
Lower Base
1
11
47155007
Left Fixing Strip
1
12
47155006
Right Fixing Strip
1
13
5862050001
Screw Kit (5” bolt)
1
14
5862050000
Screw Kit (2.5″ bolt)
1
15
5862050002
Screw Kit (1-1/4″bolt)
1