Lumio InnovaPlas AQUARIUS 5010 User manual

REV. 02/26/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
Required tools (not included)
A
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
5 lbs
x6 x6 x6
A B C
AQUARIUS 5010 WITH CLASSIC LADDER 6003
Contents of Aquarius box SKU # 5010 Contents of Classic Ladder box SKU # 6003
A weather-resistant padlock
is recommended.
MAXIMUM functional
width is 1/4’’.
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
2X
GUSSET
INSERT NUT
Phillips #2 Phillips #3
7/16 wrench
Phillips bit
Security straps
x2
x2 x2 x2
(3/4 IN.)
x18
2 1/2 IN.)
x2
SCREW BAG 140-0058
(1 IN.)
GA D B C
x2
x2
x2
x2
3/8 drill bit
Required part (not included)
IN ORDER TO INSTALL THE AQUARIUS 5010 WITH THE CLASSIC LADDER 6003, YOU WILL NEED TO PURCHASE
THIS PART:
35” PVC post, TO REPLACE THE SHORT POST IN THE 5010 BOX.
SKU # 165-0013
x2
x4
x2
(3/4 IN.)
x4
D
SCREW KIT 140-0028
x6 x6 x6
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x2
(³⁄4 IN.)
x17 x12
AB C D E F
SCREW KIT 140-0010
Contents of “Riser kit” box
x2
x1
x2
x2
x3
x1
x2
x2
x1

REV. 02/26/2020 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
AQUARIUS 5010 WITH CLASSIC LADDER 6003
D
B
E
C
D
1) Snap the three post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the filler post end into the step
as shown.
3) Snap the two feet to the bottom of
the step.
FILLER
1) Fill the bag provided with sand.
The approximate weight should
be 5 lbs.
*SAND
1) Slide the two tie
wraps in place and
place the sand bags
into the riser.
2) Fasten the tie wraps.
Do not overtighten.
4x
4x
*Sand not included
35” post
F
1) 1) Insert the two large posts and
the 35” post into the post ends and
secure them in place with the screws
provided
(as shown on the right).
2) Insert the platform over the rear post.
3) Insert the small and large
handrails as illustrated. Secure the
large handrail with the screws
provided. Leave the small handrails
floating.
4) Fasten the access panel with the
screws provided (as shown on the right).
x17
D
x3
D
x2
3
1
/
4
”
1/4”
align screws from
center of plate
E
point 4
point 1
1) Insert the two step cups in the riser.*
2) Place the riser on the ground, install the step
on top of the riser and fasten with the four
screws and plastic screw caps provided.
3) Snap the screw caps covers in place.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0

H
Security strap
1) Once the step is in the
pool secure the platform
to the top seat (see
illustration) using the two
straps provided.
x2
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the
2 screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
x2
G
1) Slowly submerge the step into
the pool. Make sure you do not
damage the pool liner in the
process.
2) Angle the whole step so that it
is entirely under water. Purge all
the air from under the step.
REV. 02/26/2020 PN: PG:3
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
AQUARIUS 5010 WITH CLASSIC LADDER 6003
J
G
I1) Trace a line on each post at 39 inches from the
ground for 48’’ and 52’’ pools. If you have a 54’’ pool,
trace a line at 40.5 inches from the ground.
2) Slide the pivot blocks onto the posts and line up
with the traced marks. Secure with the screws
provided.
3) Attach the ladder base to the bottom of the posts
with the screws provided.
4) Slide the posts through the platform. Slide the lock
over right post between the platform and the handrail.
Secure the platform using the screws provided.
5) Slide the posts through the handrails. Insert the post
covers into the handrails. If they protrude too much,
raise the handrails until the post covers are seated
securely on the posts. Secure the short handrails in
place with the screws provided.
x18
D
A
D
align for 48''
& 52'' pools
align for 54’’
A
LOCK
1) Attach the ladder to the pivot blocks with
the bolts, washers and nuts provided.
x2
x2
x2
A
B
C
SWING THE LADDER UP
AND LOCK IN PLACE WHEN
THE POOL IS NOT IN USE
TO PREVENT DROWNING
AND UNAUTHORIZED
ENTRY.
WARNING
Use sliding lock as a guide to drill hole into
ladder in up position. Use a 3/8’’ drill bit with
a cordless drill.
**PADLOCK REQUIRED**