Lumio Innovaplas ROYAL ENTRANCE II User manual

REV. 13/05/2018 PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
ROYAL ENTRANCE II (PG-2020-S-B)
Royal II Step Shell
Sand
15 lbs
Sand
(not included)
A
A philips socket screwdri-
ver bit is required.
Tools required (not included)
Use a 7/16'' wrench.
Battery operated
cordless drill
Contents of Accessory box
x2
x2 x4
x2 x8 x8
2
1/2
in.
x10x2
x2
x2
x1
x16
x2
x2
2
3/4
in.
3
1/4
in.
1
1/2
in.
3/4
in.
x2
3/4
in.
1/2
in.
x1
x2
3
in.
x1
WARNING
Do not jump nor dive from the step; you can be permanently injured.
To prevent electrocution use only BATTERY operated tools to
assemble the step.
To prevent drowning or injuries, do not use the step outside the pool
or to access a pool, and fasten the step firmly to the pool deck.
For 48,52,54’’above-ground pool only.
The step must be installed per manufacturer’s instructions.
Use of corrosive cleaning solutions can dammage the step components.
Remove the step from water when temperatures drop below freezing.
To prevent dammaging the step, never lift the step by its handrails.
The manufacturer is not responsible for damages or injuries caused by improper installation or use of the product.
Failing to install the Step CupTM will greatly reduce the steadiness of the step and will void the manufacturer warranty.
To prevent pool liner puncture, install the Step CupTM provided.
Caution
x2
3) Twist the Step CupTM to
ensure that its mushroom
has entirely cleared the wall
thickness. If it has, the
suction cup should rotate
freely.
2) With a flat screwdriver,
compress the Step Cu
pTM
mushroom ring while pushing
it into the hole.
1) Insert half of the step cup
mushroom in the hole, at
a 45 degree angle
1) Align the cap 2 guiding pins into the two top
holes in the step and snap in place.
Light cap
Insertion of Step CupTM in the step.
Installation of the light cap.

REV. 13/05/2018 PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
ROYAL ENTRANCE II (PG-2020-S-B)
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
B1
C
4) Insert the entire step
into the pool. Be careful
not to damage the pool
liner.
5) Slide the deck arms to
the height of the deck.
CAUTION
D
1 1/2 in.
3/4 in.
x4
x10
2) Secure the deck
arms to the posts with
the screws provided.
6) Drop the ballast in
the step hole.
1”Minimum
1) Secure the deck arms
to the deck using the
screws provided.
x8
3/4 in.
THIN
SPACER
ON BOTTOM
SCREW
ONLY
THICK
SPACER
ON BOTTOM
SCREW
ONLY
2 1/2 in.
3 in.
TOP POST
BOTTOM POST
Deck arm
TopPost
Handrail
2 3/4 in.
3 1/4 in.
*Adjust by
rotating each
posts prior to
fastening the
handrails.
Sand
15 LB
2) Screw the lid in
place and align the
cover ribs with the
holes in the ballast
base.
3) Fasten the 4 screws
trough the ballast base
X4
115-014 (3/4 in.)
Align holes
1) Begin the assembly with the two top
posts. Using a ruler, pick the bolts
you need: two 2 3/4’’ and two 3 1/4’’
bolts. Use the two tallest spacers and
the washers and nuts as per the
schematic Top post. Assemble the two
top posts, do not tighten yet.
Bottom post
2) Assemble the bottom posts.
Using a ruler, pick the bolts you
need: two 2 1/2’’ and two 3’’ bolts.
Use the two thin spacers, washers
and nuts as per the schematic
Bottom post, do not tighten yet.
3) Insert the post end caps into the handrails. Before
fastening the handrails , adjust the vertical alignment of
the posts by a slight rotation and affix the handrails to 4
posts with the screws provided. Before tightening the
post to the step as described in step 1 &2 , make sure
that the post are vertical and perpendicular to the step.
Post end caps
For the optional pool light installation,go to next page before you proceed with step C.
Also available; Optional safety fence to prevent swimming behind the step, for more details: http://lumi-o.com/index.php?content+usparts&lang=en-CA
1) Fill with sand
To prevent pool liner
puncture keep a
minimum of 1’’ gap
between the pool liner
and the rear of the
step.
B2-B3 Optional accessories