Lutron Electronics RCB-220V User manual

RCCB
CHECKER ( 220 V )
Residual Current Circuit Breaker Checker
Model : RCB-220V

TABLE OF CONTENTS
1. FEATURES................................................................... 1
2. GENERAL SPECIFICATIONS.......................................... 1
3. FRONT PANEL DESCRIPTION.......................................
.
2
3-1 Input Socket for Checker......................................2
3-2 Display LEDs : L-PE, L-N, N-PE and test................
.
2
3-3 Test Button (triggers test current pulse )...............2
3-4 Phase Polarity Select Switch.................................
.
2
3-5 Rotary Switch for Tripping Current........................ 2
3-6 ACV Plug for Power Cord...................................... 2
3-7 End Plug for Power Cord......................................
.
2
4. MEASURING PROCEDURE.............................................3
4-1 Checking the ACV outlet pin assignment..................3
4-2 Residual Current Circuit Breaker Test ( RCCB Test )......
.
4
5. MEASURING CONSIDERATION.....................................
.
4

1. FEATURES
* It is used for quick checking of the pin assignment for the
ACV outlet as well as for verification of the RCCB
( Residual Current Circuit Breaker ) the 5 rated tripping
current settings of 10 mA, 30 mA, 100 mA, 300 mA and
500 mA.
* Phase detection and phase inversion.
* Indication of plug assignment via 3 LEDs.
* Display of tripping pulse current for residual currents.
* Operated without battery, direct power supply from the
mains ACV outlet to be tested.
* Handy & compact ABS plastic housing case.
2. GENERAL SPECIFICATIONS
Display * 3 LEDs for pin assignment of sockets
L-N, L-PE, N-PE.
(L-Line, N-Neuter, PE-Power Earth)
* 1 LED for tripping current pulse.
Applications * Checking the shock-proof plug pin
assignment
* Residual Current Circuit Breaker Test
Rated Tripping 10 mA, 30 mA, 100 mA, 300 mA and
Current Settings 500 mA.
Test Current Approx. 140 ms to 200 ms.
Duration
Testing 200 to 240 ACV/ 50 to 60 Hz.
Voltage/Hz
Power Supply Directly from mains.
Operating Temp. 0 蚓to 50 蚓(32 蚌to 122 蚌).
1

Operating Less than 80% RH.
Humidity
Weight 200 g/0.44 LB.
Dimension 180 x 72 x 32 mm
Accessories Instruction manual..........................1 PC
Included Power cable with Plu
g
.....................1 PC
3. FRONT PANEL DESCRIPTION
Fig. 1
3-1 Input Socket for Checker
3-2 Display LEDs : L-PE, L-N, N-PE and test
3-3 Test Button (triggers test current pulse)
3-4 Phase Polarity Select Switch
3-5 Rotary Switch for Tripping Current
3-6 ACV Plug for Power Cord
3-7 End Plug for Power Cord
2

4. MEASURING PROCEDURE
4-1 Checking the ACV outlet pin assignment
a)Connect " End Plug for Power Cord "(3-7, Fig. 1) to the
" Input Socket for Checker "(3-1, Fig. 1)
b)Plug in the " ACV Plug for Power Cord "(3-6, Fig. 1) to
the ACV outlet.
c) If the ACV outlet is wired correctly, then the diodes of
" L-N " & " L-PE " are illuminated.
L-PE L-N N-PE
d)Table 1 present all the LED lamp condition
for the L-PE, L-N, N-PE, please refer it.
L-PE L-N N-PE ...
.
ON ...
.
OFF
..... correct connection
.... L and N inverted
.....
.
PE missing
.....
.
N missing
.....
.
L missing
.....
.
L and PE inverted
Table 1
3

4-2 Residual Current Circuit Breaker Test
a)Proceed as above 4-1.
b)If the LED display as following, it means the condition
of the " L and N inverted ".
L-PE L-N N-PE
Under this condition you may inverse conductors " N "
and " L " by using the " Phase Polarity Slide Switch "(3-4,
Fig. 1) to change the phase polarity.
Attention :
To select the correct phase polarity is necessary
as the RCCB can only be tripped with correct
phase connection.
c) Select desired tripping current( 10 mA, 30 mA, 100 mA,
300 mA or 500 mA ) by select the " Rotary Switch for
Tripping Current "(3-5, Fig. 1) and trigger the RCCB
( Residual Current Circuit Breaker ) by pushing the " Test
Button " (3-3, Fig. 1).
d)After push the " Test Button ", then RCCB will be
triggered if already select the correct tripping current & if
the RCCB operates orderly. Other wise the RCCB is out of
order.
4

5. MEASURING CONSIDERATION
a
)
Only use the RCCB checker in measuring circuits
with voltages lower than 263 ACV.
b
)
As to prolong life and safe operation, for the range
of 500 mA tripping current setting, please wait
approx. 10 seconds between each test
59512-RCB-220V