Lynxspring TSD 10 User manual
2900 NE Independence Ave
Lee’s Summit, MO 64064
1 (877) 649-5969 www.lynxspring.com
©2022 Lynxspring, Inc.
All Rights Reserved
Revised 3/9/2022
1. BOX CONTENTS
2.3 Procedure
e
5.2 Wi- Fi Switch
2
2. Fully Enclosed Bezel (2 Parts Back and Front)
3. USB to Ethernet Adaptor
5. Power Supply with UK and EU wall plugs
6. Screw and Restart Alan Key
1. 2 x M5 8mm Security Screw (T25)
The Tablet can be powered using the supplied Standard Wall Socket power supply.
link
Secure the rear part of the bracket to the wall or panel, ensuring an opening is available for cable
NOTE:
material types and thickness. Please use screws/bolts that are appropriate for the surroundings.
so.
3
2.3 Procedure
1. Secure the rear bezel metalwork to the wall or
matching the cut-out area on the bezel is available for
cable access.
3. Place the tablet into the bezel frame. It should be held in
place by the foam on the side of the bezel and sit directly in
the lugs, and fasten in place with the tamperproof screws.
PLEASE NOTE:
be required to secure the bezel
cover together.
4
into any content that has been setup.
key provided in the kit.
5
following screens will be observed.
No user input is required at this
point.
will be shown. Select the desired
set here if incorrect.
dialog box is not required again.
in GENERAL SETTINGS. Click OK to
6
This sec on describes the process connec ng to a network with DHCP. If a Sta c IP connec on is
required, go to either sec on 4.3 for Sta c Ethernet or 4.4 For Sta c WI-FI , then return to sec on 4.2.
For WIFI
below.
For ETHERNET
4.3.
WI-FI Connec� on Only
Select the Network from the list that has
been discovered.
WPS if preferred)
WI-FI Connec� on Only
Enter the password for the network and
click CONNECT.
7
WI-FI Connec� on Only
should now be present. Click Next.
all sources available on the network.
Once search and discovery is complete,
the Networks and Content Sources
The discovery process will list the
MAC address and associated IP
addresses. The list is sorted by IP
address in ascending order.
8
9
Select the desired Source by clicking on the blue
arrow. This will add it to the content to be
displayed.
Any number of sources can be selected,
or if desired, the same source can be
web pages, from the same source.
Click on the box to expand and view
• The source can be
renamed if required.
•
• A custom URL can be added.
Include any custom port
numbers in the URL, :8080,
:8443 etc. A colon must be
used before port numbers.
• Click to collapse the box and
save any changes.
Example Content Confi gura� on
Set Source Name:
fi r s t - fl o o r
Enabled
Set Custom URL:
:8443/fi rst-fl oor/index.html
Collapse the input box to save the
Repeat the previous steps for
each source to be added.
To reorder, press and hold the drag
and drop handle found on the right
of each saved source, then drag up or
down.
The source at the top of the
10
11
only removes this reference to the source.
It remains available in the device list.
Sources can also be added manually,
by using the ‘Add Source Manually’
Op� on
The General Se ngs menu can be
icon and any changes required should be
made before launching any content.
See the GENERAL
SETTINGS page later in this guide for
12
Once the content has been selected
and setup, click Preview.
Preview, content from
the top of the list is displayed.
A preview bar is displayed providing
screen
If more than one source has been
the loaded screen. It will show the
current source and produce a list of
sources to change to if required.
This ribbon can be removed by
disabling the Source Rota on in
GENERAL SETTINGS.
is displayed, click LAUNCH. An
Clicking NO will simply close the
dialog, clicking YES will enter the
Once in kiosk mode a restart of the
display will be required to make any
further changes to the setup.
CHANGES CAN BE MADE TO THE GENERAL SETTINGS AS REQUIRED, SEE SECTION 3
13
When connected by Ethernet to the
available, the Connec on Type
dialog box is displayed. Click on
ETHERNET.
4.3 Connect to an
Click on Ethernet in the Networks
and Content Sources page and then
Ethernet again in the Wireless &
Networks menu.
and select Ethernet IP mode. Select
sta c.
IP Address:
Netmask:
DNS1: is is same as gateway.
Gateway:
Click Connect and then Next
Any sources already
connected to the same
network will be found.
Add the content to be
displayed and preview and
then launch the pages using
Preview as per the methods
described in Sec on 4.2
14
15
4.4 Connect to an
When the Connec on Type dialog
box is displayed. Click on WIFI.
Select the network to join.
Selected network MUST be
password protected for Advance
Click on Advanced Op ons and
then drop the IP Se ngs box to
Sta c.
16
Scroll the entry box down and
A value must be added to each
saved.
Scroll to the top of entry box and
ensure the password is entered
Connect.
The network chosen should now
show as connected. Click Next to
17
Any sources already
connected to the same
network will be found.
Add the content to be
displayed and Preview and
then launch the pages using
preview as per the methods
described in Sec on 4.2.
18
General Se ngs accessed from
menu:
• Change the language.
•
Zone.
• Adjust the brightness and
dimming behavior.
•
Enabled if more than one
• Enable the password for the
•
• Reset the display.
ADJUST
NEXT.
19
5.2 Wi-Fi Switch
if your connected via an ethernet cable
completely.
•
•
•
•
•
need to be changed at any point, restart the
By default there is a hint for accessing the
TAP HERE FOR SETTINGS.
If required, a password prompt can be
menu.
The password is: ipd_admin
The display can be
restored to factory
RESET
DISPLAY
This process will reset all the
will clear all network
browser caches.
YES to proceed
NOTE: No customer
during the reset process.
NOTE:
20
Table of contents
