Crestron TPMC-3SM User manual

quickstart guide
TPMC-3SM & TPMC-3SMD
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TPMC-3SM & TPMC-3SMD
2.8” Touch Screens
The Crestron®TPMC-3SM and TPMC-3SMD touch screens install into a standard electrical box.
Both are supplied with screws for installation.
To prepare for mounting, insert a small slot head screwdriver into the hole at the bottom of the
touch screen, shown in the illustration below and gently separate the back of the unit.
1 Install the Touch Screen
QUICKSTART DOC. 7238B (2031721, Sheet 1 of 2) 04.13
1
Insertion Point for Separation of Back Panel
To mount the TPMC-3SM or TPMC-3SMD into an electrical box, use the following procedure:
1. Use the two included screws to attach the back panel to the electrical box, as shown in
the following illustration.
For U.S.-style installations, use the #06-32 x 1 1/2” screws (2031703).
For European-style installations, use the #4B x 3/4” screws (2019088).
Mount the TPMC-3SM or TPMC-3SMD into an Electrical Box (U.S.-Style Electrical Box Shown)
2. When making connections to the TPMC-3SM and TPMC-3SMD, use Crestron power supplies for
Crestron equipment.
Apply power after all connections have been made.
3. Carefully position the front of the touch screen over the back panel and gently snap it into place.
4. Insert one of the included #04-40 x 1/4” screws into the bottom of the unit to secure the touch screen,
as shown in the illustration below.
For standard applications, use the Phillips screw (2007160).
For secure applications, use the security type Torx screw (2025312).
Hardware Connections for the TPMC-3SM and TPMC-3SMD
Secure the TPMC-3SM and TPMC-3SMD
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
Screws (2)
For U.S.-style: #06-32 x 1 1/2” (2031703)
For European-style: #4B x 3/4” (2019088)
Electrical Box
Screw (1) #04-40 x 1/4”
Phillips (2007160) for standard applications
Security type Torx (2025312) for secure applications
Insert screwdriver to separate back of touch screen
NOTE: The included cable mount ferrite bead, FBLB-7 (2032427)
should be placed on the LAN cable in the electrical box.
Back Panel
For Regulatory Compliance information, refer to the latest
version of Doc. 7237.

quickstart guide
TPMC-3SM & TPMC-3SMD
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TPMC-3SM & TPMC-3SMD
2.8” Touch Screens
QUICKSTART DOC. 7238B (2031721, Sheet 1 of 2) 04.13
2
2 Establish Communication
Use Crestron Toolbox™ for communicating with the TPMC-3SM and TPMC-3SMD;
refer to the Crestron Toolbox help file for details.
There is a single method of communication: TCP/IP communication.
Ethernet Communication
NOTE: During regular operation of the touch screen, there are two ways to
activate the setup functions:
1. Place a button on the project main page and assign the reserved join
number (17242) that activates setup.
2. Press hard keys 1, 2, 3 and 4, under the touch screen display, in
sequence twice (i.e. press 1, 2, 3, 4, 1, 2, 3, 4) within a five second period.
The setup screens are the starting point for
configuring the TPMC-3SM and TPMC-3SMD.
When power is applied for the first time, the
screen shown to the right appears.
3 Configure the Touch Screen
NOTE: The only connection required to configure the touch screen is power.
Refer to step 2 in section   “Installation” for details.
Touch the screen to display the TPMC-3SM or
TPMC-3SMD “Panel Setup Options” screen, as
shown in the illustration to the right. The setup
screens enable basic configuration procedures
prior to regular operation of the touch screen.
NOTE: For details on configuring the TPMC-3SM and TPMC-3SMD, refer to
the latest version of the TPMC-3SM & TPMC-3SMD Configuration Guide (Doc.
7269). It is available from the Crestron Web site (www.crestron.com).
1 2 3 4
For Regulatory Compliance information, refer to the latest
version of Doc. 7237.
PC Running
Crestron Toolbox
LAN
Power
Injector
CRESTRON
CEN-SW-POE-5 Power over Ethernet Switch
Uplink
PoE
1234
48VDC
Power
120 Volts
POE
TPMC-3SM(D)
1
The TMPC-3SM or TPMC-3SMD connects to PC via Ethernet:
1. Use the Device Discovery Tool (click the icon) in Crestron Toolbox to detect all Ethernet
devices on the network and their IP configuration. The tool is available in Toolbox version
1.15.143 or later.
2. Click on the TMPC-3SM or TPMC-3SMD to display information about the device.

quickstart guide
TPMC-3SM & TPMC-3SMD
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TPMC-3SM & TPMC-3SMD
2.8” Touch Screens
QUICKSTART DOC. 7238B (2031721, Sheet 2 of 2) 04.13
3
4 Dimensions
0.57 in
(15 mm) 0.48 in
(12 mm)
2.00 in
(51 mm)
2.37 in
(61 mm)
1.70 in
(44 mm)
3.25 in
(83 mm)
TPMC-3SM & TPMC-3SMD Overall Dimensions (Front and Side Views)
TPMC-3SM & TPMC-3SMD Overall Dimensions (Rear View)
5 Pinout Reference
The only connector on the TPMC-3SM and TPMC-3SMD is the LAN PoE port.
3.38 in
(86 mm)
4.50 in
(115 mm)
LAN PoE
Pin Description
1
2
3
4
5
6
7
8
TX +
TX -
RX +
DC -
DC -
RX -
DC +
DC +
Pin 8Pin 1
For Regulatory Compliance information, refer to the latest
version of Doc. 7237.
6 Recommended Cleaning
Keep the surface of the touch screen free of dirt, dust or other materials that could degrade optical
properties. Long-term contact with abrasive materials can scratch the surface, which may detrimentally
affect image quality.
For best cleaning results, use a clean, damp, non-abrasive cloth with any commercially available
non-ammonia glass cleaner. Bezels may not provide a complete watertight seal. Therefore, apply
cleaning solution to the cloth rather than the surface of the touch screen. Wipe touch screen clean and
avoid getting moisture beneath the bezels.

quickstart guide
TPMC-3SM & TPMC-3SMD
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TPMC-3SM & TPMC-3SMD
2.8” Touch Screens
7 Specifications
QUICKSTART DOC. 7238B (2031721, Sheet 2 of 2) 04.13
4
Video
Streaming Formats: MJPEG
Connectors
LAN PoE: (1) 8-wire RJ-45 with 2 LED indicators
10BASE-T/100BASE-TX Ethernet port, Power over Ethernet compliant
Green and yellow LEDs indicate Ethernet port status
Power Requirements
Power over Ethernet: IEEE 802.3af (802.3at Type 1) Class 2 PoE Powered Device
Environmental
Temperature: 32° to 104° F (0° to 40° C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 14 Btu/h
Enclosure
Construction: Plastic, black or white, smooth finish
Mounting: Requires a 1-Gang electrical box or plaster ring, 1-Gang UK (BS 4662) electrical box, or 1-Gang
European (DIN 49073) electrical box; choice of standard or security screw provided
Dimensions
Height: 4.50 in (115 mm)
Width: 3.38 in (86 mm)
Depth: 1.05 in (27 mm)
Weight
5 oz (126 g)
Touch Screen Display
Display Type: TFT active matrix color LCD
Size: 2.8 inch (72 mm) diagonal
Aspect Ratio: 3:4 QVGA (portrait orientation)
Resolution: 240 x 320 pixels
Brightness: 350 nits (cd/m2) typical
Contrast: 500:1 typical
Color Depth: 16-bit, 64k colors
Viewing Angle: ±75° horizontal, +75/-55° vertical
Illumination: LED Backlit
Touch Screen: Resistive membrane
Buttons
Hard Keys:
TPMC-3SM: (2) programmable push buttons, translucent backlit, labeled with icons for “Today” and “Close”
TPMC-3SMD: (2) programmable push buttons, translucent backlit, labeled with icons for “power” and “lights”
Feedback/Backlight:
TPMC-3SM: (1) red and (1) green LED per hard key, programmable for feedback and backlighting
TPMC-3SMD: (1) white LED per hard key, programmable for feedback and backlighting
More (TPMC-3SM only): (1) programmable button, labeled with “more” icon
Select (TPMC-3SM only): (1) programmable button, labeled with “+” icon
Home (TPMC-3SMD only): (1) programmable button, labeled with “home” icon
Mute (TPMC-3SMD only): (1) programmable button, labeled with “audio mute” icon
9ȁ(1) programmable rocker button, labeled with “down” and “up” arrow icons
Reset (bottom): (1) Recessed push button behind pinhole for hardware reset
Memory
RAM: 128 MB
Flash: 256 MB
Maximum Project Size: 20 MB
Graphic Engine
16-bit non-palette graphics, 65,536 colors, multi-mode objects; dynamic graphics and text; PNG translucency;
animation, transition effects
Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP,
IEEE 802.3af and 802.3at compliant
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Crestron Toolbox and Rava are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other
countries. Other trademarks, registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names
or their products. Crestron disclaims proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
For Regulatory Compliance information, refer to the latest
version of Doc. 7237.