M-system R3Y-SV16 User manual

R3Y-SV16
P. 1 / 3 EM-8955 Rev.1
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
the contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
DC voltage input module ............................................ (1)
■ MODEL NO.
Check that model No. described on the specification label is
exactly what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when you
use this product, including installation, connection and basic
maintenance procedures.
INSTRUCTION MANUAL
MODEL R3Y-SV16
DC VOLTAGE INPUT MODULE
(16 points, non-isolated)
POINTS OF CAUTION
■ CONFORMITY WITH EC DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices and connected wires may
affect the protection level of this unit when it is integrated in
a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure CE conformity.
■ HOT INSERTION/REMOVAL OF MODULES
Removing or replacing modules does not affect other modules
on the same backplane. It is possible to replace them without
removing the power supply. However, replacing multiple
modules at once may greatly change line voltage levels. We
recommend that you replace them one by one.
■ ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ventila-
tion.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH in
order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output) close
to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises
are present. Do not install them in the same duct.
■ UNUSED INPUT CHANNELS
• Unused channels left open with certain range settings are
equal to the input lower than -15%, which sets a data
abnormality at the PLC or the host device.
In order to avoid this, use the PC Configurator Software
(model: R3CON) and specify unused channels. Refer to the
PC Configurator users manual.
■ AND ....
• The unit is designed to function as soon as power is
supplied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).

R3Y-SV16
P. 2 / 3 EM-8955 Rev.1
COMPONENT IDENTIFICATION
■ DIMENSIONS mm (inch)
TERMINAL CONNECTIONS
Connect the unit as in the diagrams below and the next page.
130 (5.12)
27.5 (1.08) 110 (4.33) POSITIONING
GUIDE
B
20 A 20
B
1A 1
RUN LED
ERR LED
Input
Connector
■ FRONT VIEW
• Pin Assignment
■ SIDE VIEW
ON
8
7
6
5
4
3
2
1
SW1SW2
ON
8
7
6
5
4
3
2
1
SW3
ON
4
3
2
1Conv.
Rate Range
Input 1-8 (SW1)
or
Input 9-16 (SW2)
•Conversion Rate: SW3
SW CONVERSION RATE
100 ms (*)50 ms 20 ms 10 ms
SW3-1 OFF ON OFF ON
SW3-2 OFF OFF ON ON
(*) Factory setting
■SIDE DIP SW
•Input Range: SW1, SW2 (selectable per 8 channels)
INPUT 1 through INPUT 8 (SW1)
INPUT 9 through INPUT 16 (SW2) RANGE
1234
OFF OFF OFF OFF
-10 – +10V (*)
ON OFF OFF OFF -5 – +5V
ON ON OFF OFF 0 – 10V
OFF OFF ON OFF 0 – 5V
ON OFF ON OFF 1 – 5V
■STATUS INDICATOR LED
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with the input circuit abnormality (AD
converter response failure);
Green in normal operating conditions.

R3Y-SV16
P. 3 / 3 EM-8955 Rev.1
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,
under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To
submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: [phone], Fax: [phone], E-mail: [email protected]
INTERNAL POWER
BUS A
BUS B*
*For dual redundant communication.
BUS CONNECTOR
20A / 20B
18A / 18B
INPUT 1
16A / 16B
14A / 14B
INPUT 2
12A / 12B
10A / 10B
INPUT 3
8A / 8B
INPUT 4
INPUT 5
INPUT 6
INPUT 7
INPUT 8
INPUT 9
INPUT 10
INPUT 11
INPUT 12
INPUT 13
INPUT 14
INPUT 15
INPUT 16
COM
COM
COM
COM
11A / 11B
15A / 15B
9A / 9B
13A / 13B
6A / 6B
17A / 17B
19A / 19B
3A / 3B
2A / 2B
4A / 4B
7A / 7B
1A / 1B
5A / 5B
■ CONNECTION DIAGRAM ■ INPUT CONNECTOR (40-pin)
PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT
1A COM 1B COM
2A COM 2B COM
3A COM 3B COM
4A COM 4B COM
5A IN16 5B IN16
6A IN8 6B IN8
7A IN15 7B IN15
8A IN7 8B IN7
9A IN14 9B IN14
10A IN6 10B IN6
11A IN13 11B IN13
12A IN5 12B IN5
13A IN12 13B IN12
14A IN4 14B IN4
15A IN11 15B IN11
16A IN3 16B IN3
17A IN10 17B IN10
18A IN2 18B IN2
19A IN9 19B IN9
20A IN1 20B IN1