M-system R80FST4NJ User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 1 / 7
INSTRUCTION MANUAL
DC VOLTAGE / CURRENT INPUT MODULE, 4 points
(4 points, non-isolated, tension clamp terminal block) MODEL
R80FST4NJ
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage / current input module.....................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and output signal for safety.
• DO NOT set the switches while the power is supplied.
The switches are used only for maintenance without the
power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■POWER UP
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for-
satisfying complete performance described in the data-
sheet.
INSTALLATION
A
B
■HOW TO MOUNT THE MODULE ON DIN RAIL
Confirm that the locking clamps of the extension power supply module
are set. Insert the module in parallel to the next one while aligning the
grooves of both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 2 / 7
• Protective Cover
The protective cover is to be attached over the connected I/O module
at the right end.
Align the hooks on the cover with the grooves of the module and slide it
straight until the hooks are latched.
When removing the cover, pull it out while squeezing the hooks inward.
Groove
Hook
■HOW TO UNMOUNT THE MODULE FROM DIN RAIL
Release the locking clamps and pull out straight the module.
Caution !
1) Be careful not to hurt your hand by pointed edges of the internal bus
connector.
2) I/O modules cannot hold tightly on the DIN rail by themselves without
power/network module.
Secure them to the position if necessary by using DIN rail end plates.
• Removing an intermediate module

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 3 / 7
COMPONENT IDENTIFICATION
■FRONT VIEW ■RIGHT VIEW
Input Connector
Internal Bus
Connector
Module Address
DIP SW
8
7
6
5
4
3
2
1
SW1
On
Status Indicator LED
Input Status
Indicator LEDs
3
4
Input
DIP SW
1
2
3
4
SW3
On
■LEFT VIEW
Terminal
DIP SW
RUN
1
2
3
4
Term
SW2
On
■STATUS INDICATOR LED / INPUT STATUS INDICATOR LED
LED OPERATION COLOR FUNCTION
RUN
Indicator LED
ON Red Upper communication: Stopping or abnormal
Internal communication: Abnormal
ON Green Upper communication: Normal
Internal communication: Normal
Blink
1 sec. sycle
– Input value error
(Exceeds the upper limit of usable range).
Blink
400 msec. cycle
– Input circuit abnormality (AD converter response failure)
OFF – Upper communication: Stopping or abnormal
Internal communication: Normal
Input Status
Indicator LED
OFF Red Input data in the range
ON Input value error
(Exceeds the upper limit of usable range).
Input circuit abnormality (AD converter response failure)

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 4 / 7
■OPERATING MODE SETTING
(*) factory default setting
Note) Be sure to unused SW 1-5 through 1-8 to OFF.
• Module Address Setting
Configurate the mosule address with DIP Switch.
0 - 15 are available for module address.
MODULE AD-
DRESS
SW1
1234
0(*) OFF OFF OFF OFF
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
7 ON ON ON OFF
8 OFF OFF OFF ON
9 ON OFF OFF ON
10 OFF ON OFF ON
11 ON ON OFF ON
12 OFF OFF ON ON
13 ON OFF ON ON
14 OFF ON ON ON
15 ON ON ON ON
• Terminator Setting
Terminator SW2
Disabled (*) OFF
Enabled ON
• Input Setting
Input Setting
SW3
1234
Input 1 Input 2 Input 3 Input 4
DC voltage (*) OFF OFF OFF OFF
DC Current ON ON ON ON

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 5 / 7
■INPUT CONNECTOR TERMINAL ASSIGNMENT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIN No. ID FUNCTION
1 Ai1 Input 1 (+)
2 AG1 Input 1 (–)
3 + Excitation supply (+)
4 – Excitation supply (–)
5 Ai2 Input 2 (+)
6 AG2 Input 2 (–)
7 + Excitation supply (+)
8 – Excitation supply (–)
9 Ai3 Input 3 (+)
10 AG3 Input 3 (–)
11 + Excitation supply (+)
12 – Excitation supply (–)
13 Ai4 Input 4 (+)
14 AG4 Input 4 (–)
15 + Excitation supply (+)
16 – Excitation supply (–)

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 6 / 7
PC CONFIGURATOR
The following parameters can be set with using PC Configurator Software (model: R80CFG)
Refer to the users manual for the R80CFG for detailed operation of the software program.
■CHANNEL INDIVIDUAL SETTING
ITEM SETTING RANGE DEFAULT VALUE
Unused setting CH enabled
CH disabled
CH enabled
Input type DC voltage -10 - +10 V DC -10 - +10 V DC
DC current -20 - +20 mA DC
Zero fine adj. -320.00 - +320.00 (%) 0.00 (%)
Gain fine adj. -3.2000 - +3.2000 1.0000
Zero base depends on input types*1-10.000 V
Full base depends on input types*110.000 V
Zero scaling -32,000 - +32,000 0
Full scaling -32,000 - +32,000 10,000
*1. For details, refer to the users manual of R80CFG
■CHANNEL BATCH SETTING
ITEM SETTING RANGE DEFAULT VALUE
Version no. – –
Simulate input Normal input
Simulated data
Normal input
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit : mm [inch]
115 [4.53]6 [.24]7 [.28] 6 [.24] 7 [.28]
DIN rail
(35mm wide)
(3 [.12]) (4 [.16])
24 [.94] 72 [2.83]
55 [2.17]

R80FST4NJ
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7029 P. 7 / 7
■CONNECTION DIAGRAM
1
8
7
6
5
4
3
2
9
12
11
10
Ai1
Ai2
Ai3
Ai4
AG1
+
-
AG2
+
-
AG3
+
-
AG4
+
-
DC voltage/ current input 1
DC voltage/ current input 2
DC voltage/ current input 3
DC voltage/ current input 4
16
15
14
13
CONNECTOR
INTERNAL BUS
INTERNAL POWER
EXC. SUPPLY
Input Connector
FE
WIRING INSTRUCTIONS
■Tension clamp terminal block
Unit side connector: MC1,5/16-GF-3,5 (Phoenix Contact)
Applicable connector: FMC1,5/16-STF-3,5
(Phoenix Contact)
Applicable wire size: 0.2 − 1.5 mm2
Stripped length: 10 mm
Recommended solderless terminal
• AI0,25−10YE 0.25 mm2(Phoenix Contact)
• AI0,34−10TQ 0.34 mm2(Phoenix Contact)
• AI0,5−10WH 0.5 mm2(Phoenix Contact)
• AI0,75−10GY 0.75 mm2(Phoenix Contact)
• A1−10 1.0 mm2(Phoenix Contact)
• A1,5−10 1.5 mm2(Phoenix Contact)